similar to: IP phones AT-723 or AT-323

Hi All; Till now I am not able to find a good IAX IP Phone or Gateway that can be used with good quality. Anyone can advise for good one? Regards Bilal ____________________________________________________________________________________ You rock. That's why Blockbuster's offering you one month of Blockbuster Total Access, No Cost.

Anyone here used these phones? I'm getting more and more frustrated by todays modern crop of routers with their so-called SIP ALGs which are invariably broken, or routers with built-in ATAs which block internal SIP phones from working, so looking to use IAX for some end-users. I already support it for people who want to use (eg) Zoiper and use IAX a lot to plumb boxes together, but never

Hello I'm thinking of selling an Asterisk server based on Atcom's IP02 solid-state unit with one FXO and one FXS ports: http://atcom.cn/En_products_IP02.htm By default, this unit based on a 400MHz Blackfin 532 chip only has 64MB RAM and 256MB of NAND flash. Those can be increased to 128MB and 1GB, respectively. Do you think I can install Linux + Asterisk + LAMP (replacing MySQL with

Hello All We purchased *25* new AtCom AT- 530 phones. Four of them did not work for even once and some of them lost configuration after some days. I talked to AT Com people over chat for support. They have just 1-2 people for support who are also busy in some other activities due to which they are unable to communicate in proper way. Often support guy left conversation suddenly and is unavailable

I've gotten nothing from http://bbs.atcom.cn on this so far. Perhaps someone on the list has experience with this. Is there a way to get MWI support for PA168V-based ATAs? Apparently some IP phones based on the PA168V chip has this support already (Atcom AT-320 for example) by configuring Asterisk with 'mailboxdetails=yes' in iax.conf. On my ATA, however, it does nothing. Any

Hello According to this article, this nice little unit can only use the PSTN port for outgoing calls (ie. as a backup in case the connection to the VoIP provider stops working), but not incoming calls: http://tinyurl.com/mwjmo8 Can someone confirm that Atcom made this strange decision, and that there's no work-around? Thank you.

Hello For customers who need a small IP PBX to handle up to four ISDN lines (in France, so I guess that means EuroISDN) instead of a PC + Asterisk and an ISDN gateway box, has someone already played with the Atcom IP-4B? www.atcom.cn/IP-BRIM.html Any feedback appreciated.

Hi all. We have Snom phones which do have a defined key in order to drop incoming call WITHOUT answering. Pressing that key, a "SIP/2.0 486 Busy Here" message is sent back. We have other phones (I.E. DECT Siemens C450IP, or ATCOM 320 or other) which DO NOT have any key to do that (or the key does not work, as is with Siemens C450 IP ): you have to answer and immediatly after hangup the

I'm looking for an ATA\Voice Gateway that runs IAX and has several ports (8 would be nice). I am looking to avoid devices that use the same firmware as the ATCOM devices as I found them to be buggy (and a PITA to find the proper update). ---------- Mike Hammett Intelligent Computing Solutions http://www.ics-il.com -------------- next part -------------- An HTML attachment was scrubbed...

Does anyone know why when calling out with an ATCOM AG-188 registered with IAX (haven't tried SIP), there is no ring. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070222/a4f29a97/attachment.htm

Hi all! I'm new with telephony cards and DAHDI drivers. I have installed Asterisk NOW 3.0.0 and update to Asterisk 11.7.0, modules are update too. I'm following the installation guide of Atcom [1] for AX1600P analogic card, modules are loaded [root at pbx ~]# lsmod | grep -E "hisax|netjet|dahdi" netjet 14618 0 isdnhdlc 4523 1 netjet mISDNipac

Hi, I flashed my ATCom AT320 phone (PA1888S based) with IAX firmware instead of SIP but now call transfer doesn't work neither using phone buttons nor using Asterisk features. I heard that it can be a real problem. Any help? Mimmus

I am looking for a gateway/ATA that can take conversations on the analogue line (PSTN) and send them to the Asterisk server on the private network. I was experimenting with the Atcom AG-188N but the "FXO"-port only supports lifeline, so it's not a real FXO-port that can send incoming calls to my private Asterisk-server. Could someone advice on a gateway that can take analogue calls

Hi Gurus. I searched the lists, wiki and the rest of the web but I still do not understand this. My Setup is as follows: [ISDN via chan_capi or IAX2 DiD Provider] => [* PBX] => [IAX2 Clients (Atcom AT-320ED)] I want to get callgroup/pickupgroup and callwaiting working on the IAX phones. Some web sources told me that this was not implemented, others say that the phone has to handle

I need to be able to connect an old PA system to an asterisk box, which basically works as a couple of amplifiers taking an analogue phone signal and playing whatever it produces out of some speakers. There is no on-hook state in the whole setup. Obviously If I just connect the input to a port on an ATA, I'll just get a dialtone played through the speakers. Can anyone think of a way I can

For those of you who may be interest.... IAX2 loads are now available for the standard builds... http://www.aredfox.com/edownloadsiax2.htm Just a word of caution... Remember to change the ports over to 4569 from whatever. And don't forget to grab the palmtool from http://www.aredfox.com/download/tools/PalmTool.zip My own testing of IAX2 with both a phone and an ATA is that IAX2 is

Hi, (please excuse me for lack of proper jargon usage and the vagueness of description...) i use Asterisk 11.12.1, (well... as included in FreePBX), . . . The softphones are mostly on machines without proper sound hardware (no mics, no speakers/headsets); This is partly because the workforce is quite conservative in what they want to use :) meaning handsets are important; As the handsets have

Hello everyone, I want to build an Asterisk Box where i need 8 FXS interfaces to connect 8 phones to. The problem is, that there is only one PCI slot available. What i have is 4 USBs 2.0 interfaces free (if this helps). So here's my question: how am i going to do this? i tried to find any PCI cards supporting 8 FXS interfaces, but without success. does anyone know such hardware? Thanks in

Hi all, Diax version 0.9.9f is ready to be tested by the interested people. You can download it for the moment from the following location only: http://www.geocities.com/tdanro/diax/diax099f.zip Please do not use older config files with 0.9.9f !!! You have some command line options now for diax.exe: /d - start with debug mode enabled /u - start with ATCOM USB phone support enabled

Folks! I would appreciate if someone could send me a simple working h323 configuration file oh323.conf that is part of asterisk@home installation. I have tried to use the oh323.conf content listed on WIKI but it is just not working as my H323 endpoint ( PA168 based ATCOM Phone) cannot register. I need a working example of this file for similar phone. Seshu