similar to: Cisco 7960G SIP Registration Timeouts

Hey gang, We have about 30 Cisco 79XX phones all running latest 7.5 SIP. We are also using all Cisco Switches and Routers. Everything works great except that when you reboot a phone it takes like 3-5 minutes for it to come up. The phones spend tons of time 'Configuring VLAN..' We don't run any VLANs. Is there some way to skip this? In the 'Network Settings' I have

Hey gang, There must be any easy solution for this but my mind is frazzled on compiling 2.4 with RTC as module. Bleh. Currently extension 9000 is our VoicemailMain(@company) line. Some employee's are complaining that the old system was better because you didn't have to enter your mailbox number and that instead the old system took you right to it. I figured there was something similar

Hi, Has anybody been successful in running the 7914 expansion unit for the Cisco 7960G IP phone? For anybody unaware of what the expansion unit does, it provides 14 additional buttons, with an LCD display. The idea, is that with an expansion unit (a 7960 can take upto 2 of these units), a user can either assign more speed-dial's, or can monitor line status/account status. So, you can

Hey gang, We currently have a class 3 switch (CSX) that..well..it sucks. It does terrible CDR writes, doesn't support LCR, the list goes on and on. We want to replace this with several asterisk boxes each running one or two 4 port PRI cards. The problem is: I can plug in 20 PRI lines into the CSX (from PSTN) and have 1 come from CSX into asterisk. If 1 call comes in on each of the 20 pris,

I could use some skinny/Cisco help here. Was finally able to get the phone registered to * but whenever someone tries to call that phone it freezes and reboots itself. Same thing happens when you pick the handset up off the 7960G; it locks and reboots about 5 sec later. Here is what * shows when I plug the phone in: -- Starting Skinny session from 64.72.107.1 Device SEP000F3442E4A7 is

I'm trying to set-up Asterisk server and I would like to buy 2 SIP phones. Has anybody tried Cisco 7960G? Or 7940? What audio compressions can I use with this phone and Asterisk? Reason why I'm asking is because Cisco supports G.711 and G.729a audio compression (probobaly some tohers but they are not listed on data sheet) and on Asterisk features i found that it supports G.729 but need

All, I'm running (attempting to) ooh323 with Asterisk and a Cisco 2621XM router operating as a H.323 GateKeeper, however when I bring the Asterisk box up it registers successfully with the GateKeeper (exchanges GRQ/GCF, then RRQ/RCF) it notes the GateKeeper supports keepalive at 300 seconds, when it gets to time to re-register its sends an RRQ again and gets rejected with RRJ (unspecified

Hey gang, I'm trying to setup the ability to dial a SIP user via their email address. I'm using SJPhone as my tester UA, but most clients will be using XTen Pro. I added an SRV DNS entry into our zone, and it returns: ; <<>> DiG 9.2.1 <<>> SRV _sip._udp.cytelcom.com ;; global options: printcmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status:

Can anyone tell me what MGCP error that I'm getting means? The hardware is a MRP200 in a Cisco 7750 PBX. (Its a FXO blade with 2 slots, first one has a 4 port FXO card and the second has 2 port FXO card. It recognises those correctly, at least to the point of this error.) MGCP Debugging Enabled MGCP read: NTFY 13 aaln/S0/SU0/0@MRP200-S1 MGCP 0.1 X: 1adace42 O: L/hd from

I've been trying to figure this one out for a while, but to no avail. I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2. Any help is appreciated. from mgcp.conf: [ubr924] host=65.37.86.203 context = from-sip (just as a

I repost a message I put a week ago: I have a Cisco IAD 2431 which has MGCP protocol; I cannot make it to work againts Asterisk; at least there is some MGCP conversation between them but when I offhook a phone attached to IAD I get no tone at all. As anybody managed to get working Asterisk against an MGCP Cisco gateway ? Which MGCP version should I use ? Also I recently

I have a Cisco ATA-188 with two POTS phones and latest stable cvs. In any situations with call waiting (existing connection and calling again) the second call cause both calls to drop. This is the same for "internal" extensions and from external (ZAP and SIP). It seems to be a "502 - The transaction could not be executed, because the endpoint does not have sufficient

HI i am trying to register mgcp gateways(Polycom 501, 601) to asterisk as a call agent, mgcp gateways are not registering to the call agent. Please help me on this if any one knows how to congigure the mgcp.conf on asterisk as well as an MGs. The following are the details of mgcp.conf on asterisk. mgcp.conf [general] port = 2427 bindaddr = 0.0.0.0 [0004f205c258] //MG MAC Address host =

Per my conversation below with digium, are there any legal alternatives to digium's G729? It is out of date, and doesn't support VAD nor silence detection. Digium has stated that they have no plans to update it anytime soon. VAD/Silence is a big deal with major carriers and we are having to fight a battle to get them to make special arrangements to turn off VAD/Silence in their

All of the stuff I've googled for and read on wiki all relate to "Outlook". Has anyone been successful in getting "Outlook Express" to do click to dial? -Matthew -- ------------------------------------------------------------------------ Matthew Boehm, IT Director Cypress Telecommunications mboehm@cytelcom.com 3838 N. Sam Houston

We have asterisk running on a quad processor dell. The kernel has been compiled with SMP. However, asterisk seems to only use 1 processor. 3 of the 4 always stay at 100% idle. Is it pointless to have a multi-proc machine? I was going to buy a new dual 3.6Ghz Xeon server but if nothing will take advantage of the other proc... Perhaps my conception of multi-proc/threaded is warped. If asterisk is

I'm trying to link up Cisco MGCP-enabled router (residential gateway) with Asterisk, and it looks like some sort of protocol mismatch, could it be MGCP 0.1 vs 1.0? Look at this (x.x.x.99 is the router, x.x.x.98 is Asterisk): MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427Verb:

Hi! I have strange problem, I hope it's just a configuration problem, but maybe not. I'm trying to make a call between a MGCP gateway and Cisco 5300 talking SIP. Everything is fine except that audio is one way (from 5300 to MGCP gateway only). It seems that during reinvite Cisco gets confused by session ID and version and excpects RTP stream on different port. The call flow on SDP

Does anybody has the expirience configuring Asterisk with Cisco ATA 186 MGCP firmware ? I have Cisco software v3.1.1 atamgcp (Build 040629A) Asterisk 1.0-RC1 On ATA i only put domain test. mgcp.conf looks like this [test] host = 192.168.195.55 context = default line => aaln/2 line => aaln/1 Asterisk CLI shows this: Jul 31 16:05:40 WARNING[135449600]: chan_mgcp.c:485

Hello, I want to optimize my registrations and calls of peers to my asterisk with the following options in sip.conf: ---///--- qualify = yes qualify = 500 qualifyfreq=5 registerattempts = 0 registertimeout = 10 maxexpiry = 60 minexpiry = 20 defaultexpiry = 600 ---///--- Can someone more experienced with these settings to help me to optimize connections from peers with mobile phone that using