similar to: Asterisk + NetJet (ISDN4Linux)

Hello, I just got my isdn-card working together with i4l and asterisk. Everything seems to be working fine: I can accept calls coming from the outside and I can dial out. Even setting the msn works like charm but my problem is that I cannot hear a word. There's complete silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network

I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing

Hello, I am trying to use 2 netjet cards under asterisk and isdn4linux. I am having a hard time trying to get them to work in terms of dial out. Does anyone have a working config I could look at for even one card (tried that, not much luck either). When i dial out: -- Accepting AUTHENTICATED call from 172.16.11.2, requested format = 2, actual format = 2 -- Executing

Hello all, I currently have an Eicon Diva Client isdn card using i4l. Outbound dtmf doesn't work (and never has), but there has been an annoying problem with false dtmf detection in calls (that could be triggered easily by blowing into the receiver on the remote end). I looked through the list and found two patches that need to be applied - 1 to isdn_tty.c in the kernel, and another to

Hi all, this is a rather "newbie-oriented" question, so please bear with me... The system running Asterisk has been provided with an AVM FRITZ!Card PnP. SuSE Linux 9.0 recognizes it right after booting the system and it seems to be configured (MSN) correctly... The hwinfo looks like this: --- pbx:/etc/asterisk # hwinfo --isapnp 11: ISA(PnP) 01.0: 10300 ISDN Adapter [Created at

Hello! Im pretty new of asterisk world: my goal would be using iaxcomm to call ppl over POTN. Yesterday i configured asterisk to be able to hear a song (with Playback() command) with iaxcomm, and it was wonderful. Now, today i tried to configure asterisk to use my ISDN4Linux supported card (a plain HFC card) with asterisk. i configured modem.conf this way, after reading

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm having some problems using the asterisk modem driver with an ISDN4Linux card (AVM Fritz). (I realise that it's better to use CAPI, but unfortunately this card doesn't have any CAPI drivers). Every so often the ISDN just stops working (it neither dials out nor accepts incoming calls). Trying to dial out just logs: --

The card is an ASUSCOM ISDNLink PCI (passive) and the circuit is from Qwest (in the US). I will be using this circuit only for voice (I'm doing this because of the poor quality of my POTS lines). I've compiled Hisax (as a module) into my 2.4.25 kernel, and with 'modprobe hisax type=35 protocol=4 id=hisax' I get the following: Apr 7 10:34:24 dev kernel: HiSax: Linux Driver for

Hello everybody, I have a strange comportment with oh323 and asterisk, I'start testing asterisk but with this I can't understant plesae help me ! Thanks Eltorio ---------------------------------------------------------- 1/PB: I can't dial from a H323 extensions (registered on a GNU GK) to a Modem[i4l] line ---------------------------------------------------------- Nothing happens

Hi *, This is my first message to this list, so I hope I am not breaking any rule with my post. My question is the following: can I establish a voice connection over an ISDN interface by using a bluetooth dongle to connect to the ISDN access point? Here follow the details: I have compiled and configured asterisk. Everything seems fine except that when I configure asterisk to use the ISDN

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

Hi, Apologies in advance for the lengthy email. I'm new to asterisk and have trouble with isdn4linux. The setup is very basic like this: winxp ------- asterisk -------- winxp x-lite | x-lite | pstn The hardware involved is: Compaq EVO with RH9/kernel 2.4.20-30.9. Fritz!Card PCI v2 Asterisk CVS-04/17/04-21:36:18 Basically

Hi to everyone! I am new to this list and i want to greet you all! I am trying to install Asterisk on a Fedora Core 3 Distribution with a Digi Datafire Micro V ISDN Card. I know that I have to use the ISDN4Linux so in modem.conf I set the I4l driver ,the msn and device. Modem.conf [interfaces] context=remote ;driver=aopen ; modem by AOpen driver=i4l ; isdn4linux - an

I posted a message a little while ago but got no response (that I can recall), I've also seen other people mention this issue. Basically, when you have music on hold, it doesn't play the music on hold, the debug info shows it is starting and then stops straight away.. # My extensions.conf ... exten => s,1,Answer exten => s,2,DigitTimeout,5 exten => s,3,ResponseTimeout,10 exten

Hi all, I'm playing with Asterisk and I've already configured all needed .conf files. It works quite well, but now I need your help to tune the system: when I place a call from a softphone to the PSTN, I can't hear directly Telco's tones and I can't use its services, e.g. a mobile's answering machine. I don't know if I have to modify the dialplan or if it depends on my

I'm trying using Asterisk over an isdn line. I configured my Eicon Diva card by the hisax module and it works with the Asterisk's chan_modem (and chan_modem_i4l) driver. The problem is that I can receive calls (on /dev/ttyI0) but when I make a call I always have the line busy (on ttyI0 but even if I use an other device like ttyI1). This is a part of my consol output: --

Greetings, today I'm recompiling asterisk on a new machine with the same isdn card (not the same model, the *SAME* card) using CVS downloaded yesterday night. When I try to start *, it gives me the error: [chan_modem.so] => (Generic Voice Modem Driver) == Parsing '/etc/asterisk/modem.conf': Found == Loading modem driver chan_modem_i4l.so => (ISDN4Linux Emulated Modem

All, Currently I've got my Asterisk machine running smoothly on IP bases. Meaning I can reach all phones or softphones within my LAN or remote LAN's via VPN. The next step for me is connecting it to the PSTN network. After some tweaking with the modem.conf I got the i4l driver running correctly, and it appears that my Fritz! ISDN v2 card is working correctly. I have added the

Hi everybody ! I've a Pentium IV with a USR ISDN PCI Card W699. Card I've installed asterisk 1.0.0 and it's working fine with outgoing call to POTS But it never answers to my incoming call from POTS and I don't understand why. I tested the modem also with the minicom utility and I never saw the "RING" status It seems that the modem didn't know somebody is

Currently we have problems with our asterisk server connect with an Eicon Diva 4BRI Card to a PBX. Asterisk is running in version 1.0.0 on RedHat Enterprise Linux 3AS with kernel 2.4.21-4.EL. The Diva server is running in version 7.5 Can someone help us in reolving the errors with incoming calls? When we try to call to an extension we get these messages in the CLI: -- creating pipe for