similar to: isdn, pbx and *

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi i've installed asterisk by last cvs and i note res_parking.c is not anymore there; chan_capi-0.3.4b INSTALL file require: in /etc/asterisk/modules.conf insert the line: load => res_parking.so load => chan_capi.so running asterisk i get: [app_capiCD.so]Jul 21 15:32:26 WARNING[1076988448]: loader.c:242 ast_load_resource:

Hello, I have the following problem with HFC card and Alcatel PBX 4400: - I want to connect Alcatel PBX and Asterisk with HFC card (zaphfc driver 1port S0/T0 interface card) - BRI line is configured at PBX to T0 trunk - In asterisk I have loaded zahfc driver in NT mode and also set in zapata.conf NT mode, point-to-multipoint. - I am using cross "isdn" cable to PBX -

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 hi, i'm new to * I've installed an hfc-s card (DIGI Micro V) with bristuff 0.0.2; when i try to call outside i get: -- Accepting AUTHENTICATED call from 192.168.1.110, requested format = 1024, actual format = 1024 -- Executing Dial("IAX2[pippo@pippo]/2", "Zap/g1/0123456") in new stack Jul 13 13:42:49

Hi there asterisk goes to 90% cpu usage when trying to authenticate a sip friend using realtime mysql, no other message does appear at cli and asterisk hungs; here some info: *CLI> realtime load sipfriends name 104 Jan 13 11:52:21 DEBUG[8928]: res_config_mysql.c:109 realtime_mysql: MySQL RealTime: Retrieve SQL: SELECT * FROM sipfriends WHERE name = '104' Jan 13 11:52:21 DEBUG[8928]:

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Ddoes it feasible with * to capture a call? when arrives a call, floor bells ring and everyone can hear them in the company, then everyone can answer 'capturing' the call m. - -- Maurizio Marini GSM +39-335-8259739 Work: +39-0721-855285 Fax +39-0721-859609 Home: +39-0721-950396 IAXTel: (700) 350-1234 -----BEGIN PGP SIGNATURE----- Version:

hi, i just found a page on the net which might me worth some lines. for the urgent reader: http://isdn.jolly.de there is a guy in germany who has successfully programmed a gpl-patch for isdn4linux to make isdn cards with the hfc chipset from cologne chip (http://www.colognechip.com) run in the NT mode (up to 2.4.20). this mode is needed to connect isdn device to a pc and enables the use of

Hello I try today to install samba 4.13.1 ? ./configure run without error Make run without error Make Check Failed Debian 10.6 Also all required Packages are installed -- # cat summary = Failed tests = == samba4.blackbox.demote-saveddb == command: PYTHON=python3 /usr/src/samba-4.13.1/testprogs/blackbox/demote-saveddb.sh $PREFIX_ABS/demote

I have a problem with Asterisk-bristuffed using a zaphfc card. I am located in the Netherlands, so I have an ISDN line from KPN. When I start Asterisk, and plug in the ISDN line, everything works perfectly for about 5 minutes. And then the ISDN line is down for 1 minute, and after that minute, the line comes back up and works for another 5 minutes. Every time the line goes down I get the error

Hi, I've set up an Asterisk as voip gatway: VOIP <-> Asterisk <-> hfc-s card <-> NTBA <-> Siemens Gigaset Dect ISDN pbx. Outgoing calls from dect handset to the world are working. Incoming calls don't even ring the handset. I'm using the dahdi driver with the zaphfc kernel module. The hfc-s card is in nt mode. The msn is set at the dect phone/base station

Hi, I am looking to integrate Asterisk with a Siemens HiCom 150e via BRI and wondered if anyone is able to offer any advice. In simplistic terms, my goal is to pass calls from the HiCom to the Asterisk box. e.g: HiCom user dials access code and can call Asterisk extension or establish SIP call over Internet. Likewise, I'd like Asterisk to be able to present a call to the Hicom, either

Hi, I'm setting up an asterisk server with this hardware configuration: AMD Athlon 1000 Mhz 256 MB ram 3ware ATA raid controller 2 * Ethernet controller 2 * ISDN HFC controller One ethernet controller is connected directly to the internet (public IP) One ethernet controller is connected to the internal lan One ISDN controller is connected to the public telephone network One ISDN controller

Hi i've an hfc-s card with last bristuff installed at cli> i'm receiving: Sep 8 12:35:20 WARNING[1109552048]: chan_zap.c:6902 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 received TEI check request for TEI = 77 what is causing them? 10x Maurizio

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

Yes, it is possible to connect an ISDN to analog A/B adaptor to the HFCPCI. I'm working though with the zaphfc module and the HFC card in NT mode. Then I use a (very) old PTT Moduvox 2a (only known in Netherlands I think) which is connected to the HFC card. The moduvox is a small home exchange with 1 ISDN and 2 analog connections. It provides it's own power so I don't need power on

Klaus-Peter (while hardly able to see through my watery eyes), You've earned yourself a (potentially rackmountable) 19" Dutch cheese as soon as the zaptel driver is finished and tested. In fact, I don't even have to mail it, I can pratically bring it over ! Although I'll be monitoring your site on a 24hrs/day basis from now on, please keep me posted on both the driver and the 4

Hi! I am trying to get my ISDN phone to work with my asterisk box. Now my asterisk won't start. Current situation: I have a cable from my Billion ISDN (Bipac V1.0) to my old NT1. The cable is crossed like this: 1 2 3 -> 4 4 -> 3 5 -> 6 6 -> 5 7 8 Then I have a cable from the NT1 to the ISDNphone(not crossed cable). Both cables are connected in the ISDN

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 i fixed wrong capi.conf (there was [controller1] after [interfaces]) now capi.conf is: ; ; CAPI config ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] msn=855285,859609 incomingmsn=* controller=1,2,3,4 softdtmf=0 accountcode= context=local ;echosquelch=1 ;echocancel=yes ;echotail=64 ;callgroup=1

Hi, Bristuff works great with HFC card... your compilation problem may come from your kernel configuration... You should check this doc, at least, for the redhat config : http://www.automated.it/guidetoasterisk.htm Then, installation of Bristuff works like as charm ! Bye David Masure -----Message d'origine----- De : vdasilva [mailto:aquamoon@wol.co.za] Envoy? : mardi 28 juin 2005 09:01

Hi, It's the first time i try to configure an ISDN card with dahdi, so my experience is very poor (be kind ;)) My problem is with dahdi_genconf, when i start it it says: /usr/sbin/dahdi_span_assignments: Missing '/sys/bus/dahdi_devices/devices' (DAHDI driver unloaded?) Command failed (status=256): 'dahdi_span_assignments dumpconfig > /etc/dahdi/assigned-spans.conf' at

Hello I have asterisk running in Red Hat 9 with a cheap HFC card on i4l. I have choppy sound problems sometimes, and echo problems often. I am using a 2 port Grandstream ATA, Grandstream BT and a Grandstream GPX-2000 I read that changing to BriStuff will fix the echo problems, but have also read other users say that the only way they solved the echo/choppy sound problems was using a Fritz ISDN