similar to: HFC cards and Asterisk

Hi there, I've got a small problem with the zaphfc channel. No MSN of an any incoming call which comes trough the ISDN card (Acer ISDN, with HFC chipset and zaphfc driver) which will be forwarded to the SIP-Phone will be displayed. Always it will be shown "asterisk" an the Display. --- snip (zapata.conf) --- [channels] language=de switchtype = euroisdn signalling =

We have 2x BRI's connected to Asterisk which give us a total of 4 lines (using the bristuffed package). We would like to limit the number of incoming calls to 2 calls and if a 3rd call comes in, we would like this to go to another extension (voicemail or similar). Is this possible in Asterisk? Thanks -- James Doherty - Systems Engineer Zeald.com - Websites That Work! Web: www.zeald.com | Ph:

Hello, I've added a ZAPHFC card to my CAPI based system. Calls coming in via ZAPHFC do not forward the caller id to the SIP phones. Calls coming in via CAPI do forward the caller id to the SIP phones. Any and all help is greatly appreciated. The (hopefully relevant) conf file excerpts are: extensions.conf =============== exten => 807440,1,Answer exten => 807440,2,Noop exten =>

I have a "Cologne Chip Designs GmbH ISDN network controller" in my asterisk box, and an ISDN line connected up to it. I downloaded the bri-stuff 0.1.0-RC4a package from junghanns.net and used that to compile asterisk using these instructions: http://www.voip-info.org/tiki-index.php?page=Asterisk%20zaphfc%20install When I try to call my asterisk box, my sip phone rings twice and then the

Hi, I'm a newbie on * trying to setup an HFC card. I'm locked for many days getting the all-circuits-busy. And no idea what else to look for/how to diagnose. I'm in Spain, I've tried changing many parameters on zapata/zaptelcong with no luck, also NT & TE modes (honsetly, I've no idea what is). Any clue will be very much appreciated! I've installed *@home on my RH9,

Mine is very similar: i don't have echocancelwhenbridged=yes because it seems work only on TDM, is it ? And in Italy, I often have set pridialplan = unknown About echo I have some problems, but only at the beginning of the call. After 3-4 seconds the echo became almost null, specially with snom 190; with pa168s and ywh10 I have again some problem, the echo come up also after 1 minute of

Hi, I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1 debug=1). So i want to test two cards and make loop between them. So one card would be NT,

I'm using a Grandstream IP phone to call someone through our asterisk pbx. The PBX is running "Asterisk 1.0.3-BRIstuffed-0.2.0-RC3" and uses 2x ZAP-HFC cards. When I call someone, if the call isn't answered and then I hang up, I get "487" coming up on the grandstream phone. If I pick up the receiver again and then hang up, the PBX starts calling me back and when I

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

Hi All, It's broken !! (drat) Asterisk if failing to load with the following error (taken from end of /var/log/asterisk/full) after adding bristuff. Can anyone help please? Jul 17 19:57:54 VERBOSE[2503]: == Registered channel type 'Phone' (Standard Linux Telephony API Driver) Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so]Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so] =>

Hi list, Attempting to get an ISDN-BRI line connected using an HFC-S PCI card together with Asterisk v1.4.14 and Zaptel 1.4.7 on a Debian etch system, I find that I can't access the card's resources because the channels are always be busy. An attempt to call out results in the following CLI output: == Primary D-Channel on span 1 down == Primary D-Channel on span 2 down

I guess it is possible to have an HFC-S card and a Digium TE110P card working at the same time? The TE110P will work in E1 mode. I think the zaptel.conf is probably right but the zapata.conf not (I just tacked on another group at the end but I don't really know what I am doing). Can anyone help? ----------------------------------------- My zaptel.conf looks like this: # hfc-s pci a span

Try commenting out the line pritrustusercid = yes Or set it to 'no'. That worked for me. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Jens Sent: Friday, January 21, 2005 7:18 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] zaphfc no callerid

Hi list, Now that I've got my Asterisk server to recognize my HFC-PCI card, I've run into some serious problems. The first thing I noticed was this message that would show up every five seconds on the CLI: Dec 27 15:46:42 WARNING[12484]: chan_zap.c:2512 pri_find_dchan: No D-channels available! Using Primary channel 3 as D-channel anyway! == Primary D-Channel on span 1 down

Hi!I've installed Asterisk@home and I have a ISDN card,(Cologne Chip Design GmbH ISDN network controller [HFC-PCI](rev 0.2) This is how I installed bristuff: how to install hfc card after unload asterisk and amportal whit amportal stop type "setup" unselect zaptel in system service... and set the lan --->reboot<--- cd /usr/src wget

Hi, I'm trying to set up an Asterisk pbx based on a Fedora Core 1 Linux box (customized kernel version 2.4.24). I want calls from my SIP soft-phones to simply be dumped onto the PSTN line via a BRI (EuroISDN). I have a cheap HFC-S based PCI ISDN card connected to the NT1+ interface, so I need zaphfc. I've read everything I've found at www.voip-info.org, then I've downloaded the

Hi list! I am installing an * box that will be installed on a site with KPN BRI ISDN in The Netherlands. I am using bristuff fron Junghanns. Does anybody know the correct settings for this? I will not have internet access there which makes it harder to google around on location. switchtype = euroisdn is pretty obvious but what about these settings: signalling = bri_cpe_ptmp ; p2p TE mode

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

Hi! I'm struggeling had to get a hfc pci card working in NT-Mode. I've installed a very basic test system with just one hfc pci card connected to an ISDN-phone over a modified NTBA as described on jollies homepage. I commpiled asterisk as descibed in kape's INSTALL file that comes with 'bri_stuff'. I have not modified the config fieles yet. After connecting to asterisk by

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the