similar to: Newbie needs help - Dev_Kit_Lite installation problem

Hi, I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error (EB113 on the display) I am learning linux and asterisk as I go along, there might be obvious things I should know, but bear with me. >From demsg below my 2 digium cards installed are listed (no config or connections done to digium cards yet), the conflict is with the TDM400P card, without that card, in any slot, no

Any thoughts on the following? I am running asterisk from CVS (downloaded yesterday's version, just to be sure) on a test system with no digium cards in it, so I have installed ztdummy (see logs and screenshots below) as a timing source. When I call the music on hold extension from a Sipura Sip connected analog phone, I hear nothing and start getting Warning[98310]: chan_sip.c:674

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

When I try to start up zaptel, whilst running ztcfg, I get the following error: Jan 1 10:48:18 bu ztcfg: ZT_CHANCONFIG failed on channel 2: No such device or address (6) My /etc/zaptel.conf is: fxsks=1 fxoks=2 loadzone = au defaultzone=au Channel 1 is a X101P card connected to the PSTN and channel 2 is a S100U box driving an analogue phone. The zaptel kernel module gets loaded OK as does the

Hi, I have been trying to figure out why the S100U is not performing very well on RH9.. Here is my thinking..( may be totally wide of the mark but here goes anyway) I remember reading somwhere that the sound system used by RH has changed... Does the S100U not depend on the sound subsystem?? So what I think is that the sound subsystem in RH9 and the S100U are not happy working together.. Does

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I've tested the S100U unit in two different computers both with different USB subsystems. The one it worked the best in used the usb-uhci USB driver. The other system uses the usb-ohci USB driver. To make sure it was not the installation, I used the same hard drive that had asterisk in both systems. And I moved the X101P and S100U between both

Hi all, this is another post about this problem. I installed from scratch a new Suse Linux 10.0, with latest stable asterisk. Moreover I add the lines to /etc/udev/rules.d/50-udev.rules, in order to let the driver create the /dev/zap....... When I plug into usb port my TigerJet adapter, I see on /var/log/messages Feb 24 14:55:02 srvlnx05 kernel: usb 1-2: new full speed USB device using

I'm trying to install on a 233Mz PII running RH7.1 kernel 2.4.2 The "astinstall" script pulled files from CVS ok and compiled with no warnings. When I try to run "modprobe wcfxo" and "modprobe wcusb" I get the following identical set of error messages: 15. Creating sample environment...SKIPPED ================= Installation Completed! ====================

I installed Asterisk as per instructions in the FAQ on the digium.com site. Double checked it. I also think they have a bug in the zapata.conf where the context should be incoming and not internal. 1) I hear no dialtone when I pickup the phone on the S100U. Asterisk sees the event and displays the message on the screen. I tried dialing but nothing happens. I hangup and * shows the hangup event.

I'm attempting to configure a machine with a DevKit Lite (X100P & S100U). After I modprobe wcfxo, the machine goes into some kind of loop after about 10 seconds, where it spits out what appears to be 32-bit addresses, ad infinitum. At this point, the machine becomes completely unresponsive to keyboard input (i.e. Ctrl-C, Ctrl-Alt-Del, even CapsLock and NumLock states [lights] cannot be

I'm having a bad time getting 3 TE410P's and one TDM400 working in the same box. At some point during the install of second card, wcusb starts loading. I believe this is one of the TE410 Cards causing this as there is no usb enabled. Module Size Used by Not tainted audit 89880 2 (autoclean) usbserial 23420 0 (autoclean) (unused)

I'm afraid that I am at a loss here. I am new to Asterisk, and have successfully set up SIP. But I cannot get my FXS card working, and I'm not sure what else I can try. # modprobe wcfxo /lib/modules/2.4.21-37.0.1.ELsmp/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may

Does anyone keep a known telemarketer caller id database? If not has anyone proposed an Asterisk community project to share this information? Sort of a nation wide blacklist so Asterisk'ers can cut down on the garbage calls... -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have the dev kit lite installed, and after compiling and installing asterisk, I've become a little confused about how and when wcfxo and wcusb are loaded. When ever my box is done booting, the wcusb module is loaded, but the wcfxo module is not. Further, even though my startup notices say that asterisk started OK, it is not running by the time I log in and do a ps. First, where are the

Hi Everyone, I've been using Asterisk now for a few months for my small office (which is mostly just me while other guys are always on the road so we rely heavily on telephones) - I'm very excited with Asterisk as it can do everything I've ever wanted to do with a PBX. I'm having a problem with an S100U USB --> Telephone interface. I haven't actually made it work yet

My system seems to be generating a call on its own... Unfortuately I can't give much more information.. I have an X100P and an S100U.. My Modem and the X100P share a common line.. When I am on the internet (which is most of the day) * just sits there and does nothing (apart from when I am testing ideas for the dial plan), but at night when I am sleeping and the modem is not connected then

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

Hello. Well I finally rx'd my dev kit (new batch of TDM's apparently. I'm on Mandrake 9.1 There were no hardware install instructions, it would have been nice to know whether the 4-way power connector was to be used or was for some other future or expansion purpose. It came with a floppy disc, no label and it wasn't even write protected. The only readme file was

>From - Received: from rwcrmhc12.comcast.net ([216.148.227.85]) by sccrmxc11.comcast.net (sccrmxc11) with ESMTP id <20031014185753s1100nos46e>; Tue, 14 Oct 2003 18:57:53 +0000 Received: from rwcrmhc12.comcast.net (localhost[127.0.0.1]) by comcast.net (rwcrmhc12) with ESMTP id <20031014185753014006qmtie>; Tue, 14 Oct 2003 18:57:53 +0000 From: Mail Delivery Subsystem

Hello, I'm running asterisk-1.0.6 on a centos3.4 box. I'm still in testing phase and so far everything is running smoothly. I'm now trying to play a soundfile or an mp3file using 'MP3Player', 'Playback' or the 'Background' commands, but don't get any sound. The logfile says: -- Executing BackGround("SIP/joa-9def", "tt-weasels") in