similar to: Distinctive Ring Cadences

I'm using Asterisk 1.4.5 (will try 1.4.6 on Thursday, but I don't see anything in the changelog after the 1.4.5 release dealing with distinctive ring), zaptel 1.4.3, and wanpipe 2.3.4-10 with a Sangoma A200 card. I enabled usedistinctiveringdetection in zapata.conf. However, on the Asterisk console, the output I get is: -- Detected ring pattern: 0,0,0 It would appear that Asterisk is

Group, Just want to share with the group my recent findings regarding CODECs/Vocoders and the effect it has had on voice quality and the intermittent noise and breakup problem I have which I mentioned in a previous emailing with the u-law CODEC. Calls again are placed through a SIP phone to a TDM400P to the PSTN. A good reference on the reasoning behind the selection of a CODEC was found in the

Has anyone had any experience with wireless LANs and Asterisk? We have and here are my impressions. We configured an Asterisk in the office as a precaution to see how it would work for our own retail customers. Our office is open space, about 800 sq ft. (20x40 area). We use Snom200 and Grandstream SIP phones. Using the latest Linksys wireless access point (WAP54g) and 3 wireless bridges

I have a line from BT (UK) connected to my asterisk system, on a TDM400P. I am able to see either distinctive ring cadences or caller ID but not both. If I try to enable both, all drings show up as 0,0,0. This is a pain because, if I make a call out over that line and the number I call is busy, I can elect to camp on it (ringback), which results in a different cadence of ring when the called

Hi All... Is it possible to cause asterisk to answer some distinctive ring patterns but not others? I have a POTS line plugged into an X100P and I would like * to ignore one ring cadence that is answered by a fax machine. How would I do that? Thanks...

Is there a way I can change the ring cadence on FXS lines on a system using a Digium Wildcard TDM2400 card? I recently deployed a new phone system, and the customer has a few POTS phones in areas where they don't have data network services, so we're using the FXS lines to provide dialtone at those outbuildings. The old phone system would ring those phones with a short ring-short

I am somewhat unsure as to the definition of "Distinctive Ring". What I am trying to achieve is to have Zap connected phones (TDM400P) ring with different cadences depending on whether the call is incoming on the PSTN context or an IAX2 context. Googling, I find this from Mark: I've added distinctive ring support to Asterisk now (also I've added answer confirmation which is

Hi Can anyone with distinctive ring on their 7960's possibly post how they've got it to work? I understand that the ALERT_INFO variable is involved but using the examples for the variable value from the WiKi I'm just getting an error message from the Asterisk concole. Thanks in advance. P

Hi All, I was wondering what the status of distinctive ring support in Asterisk is? I had a google search & read and Mark Spencer wrote some support for it. Is distinctive ring different in every country or is it pretty standard? And for my final question, does the Wildcard FXO card support distinctive ring? Essentially what I'm trying to do is route incoming calls with ring #1 to,

When did Dial() with a custom ring cadence replace the default from indications.conf for subsequent calls? indications.conf: ringcadence = 2000,4000 asterisk -rx "dahdi show cadences" r1: 667,1333 extensions.conf: exten=> 201, 1, Dial(DAHDI/1) exten=> 202, 1, Dial(DAHDI/1r1) exten=> 203, 1, Dial(DAHDI/1r0) Dialing, in sequence: 201 -> 2000,4000 ; Good 202

All; Since I have interest in providing the capability for callers to speak the department, person or number they wish to call, as well as other IVR scenarios, I have been reviewing much of this lists email archives and searching the web for open source voice recognition that will work with the Asterisk PBX. What I am trying to determine, is what will it take to get it working on Asterisk? How

I am looking for clues on how to configure distinctive ring for a PolyCom SoundPoint 300. Does ALERT_INFO apply? If so, how? Thanks, David Koski david.nospham@kosmosisland.com

This is an Australian situation. I have a PSTN connection that has CLID presentation enabled and has two numbers assigned to it, the primary number with the standard ring cadence: 400,200,400,2000 and the secondary number with the alternative cadence: 200,400,200,400,200,1600 CLID presentation is working fine and in zapata.conf I have: usecallerid = yes usedistinctiveringdetection = yes I am

Hi all. So.. as the problem with the video driver and CentOS 5 seems to be hard to solve, I'll try to migrate to CentOS 6. I'd like to ask if anybody is successfully running cadence and plugins on CentOS 6 and if it is running as well as it was on CentOS 5.. If any, what problems may I see running cadence on CentOS 6 ? Thank you very much! Robi

>Another option is Aastra's Ring Selectors. They can "split" a line into >multiple lines by ring cadence. > >http://www.aastra.com/Products/RingSelectors/index.html Don't you then have to wait 4 rings b4 an extension will get a * dial ? This devices must wait 2 rings to detect the cadence then * is gonna wait 2 rings trying to get CallerID which I think it will NEVER

Help. Why is it that I can call out from my GSBudgetone SIP phone but the audio is "one-way'? Why is it that when I call my asterisk phone number, I get a fast busy?

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

I edited zapata.conf to use custom ring cadences. Seemed to work, but upon some restarts, seems zapata.conf is not being read properly on startup as zap show cadences will show the defaults. Some restarts show the custom cadences. What's up with that? joe a.

Using distinctive ring detection with bell202 cid, is there any way to tell DAHDI to sometimes expect the cid after the 2nd ring, other times after the 1st? I just added RingMaster service (2nd DID w/ distinctive ring) to a TDM800P FXO line. No problem setting dringcontext for the 2nd DID. The 1st DID works normally, but I get no CallerID on the 2nd because the call is picked up before the

I have a TDM400 with 2 FXS cards, and a Samsung 6100 DECT base station connected to one of the ports. The base station appears to only support UK (BT) style CLIP Caller ID signalling. Does anyone know if it is possible to configure the ZAP channel to send in this format, or alternatively can you recommend a GAP compatible base station which will handle both BT and Bellcore signalling? A search