similar to: Warning when I use iax2 for inbound and outbound calls

I feel this is in error some place. If I call a sip device that is not registered or not connected at the time. Asterisk will send that call to voicemail to busy not unavailable. Is there a way to correct this? Ariel Batista Kasi International - Computer Networking Ph: 305-574-6721 Fx: 305-574-0212 -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have a problem which I need to resolve. We are trying to put an asterisk between a Mitel PBX and the world. We are adding Voip service via Asterisk. Here is are config files for the settings but our problem is the following. We are able to send calls to the Mitel pbx and it's the T1 connections is green saying it's ok. The support department from Mitel said that they use e&M and

Ok here is another problem I have run into. I have a Sipura 2000 and I have been able to configure line 1 with only one small problem. But I can't get the line 2 working with asterisk. Here are samples of my sip.conf and extensions.conf. If I disable line 1 I can then get line 2 working. Is there a sample configuration for the Sipura to get both ports working with Asterisk. Sip.conf

I just got 2 IpDialog phones for use with my Asterisk system. I have been able to get the phones to just dial local extensions but it is not able to register with my system correctly. I would like to know if someone has set these phones up before and how they did it! Is there any examples for use with Asterisk? They seem simple enough to config with there web interface. Thanks

I would like to know if anyone has come up with a script for 911 dialing rules that put correct information on our locations. We have our office in 3 different building one being our production & shipping dock. It is almost 2 blocks away. We are connected with Ethernet Wireless between the buildings and have Sip phones setup in the other 2 locations. All the phones are working just fine.

It should be a mpg123 problem, not a spandsp problem. Stop asterisk, make clean, make install and start asterisk again. Have fun. "Ariel Batista" <arielb27@hotmail.com> wrote in message news:<BAY22-DAV14862521E60E81DB568FDCDBB60@phx.gbl>... I have compiled Spandsp without any problems. I got no errors I have also done the patch without getting any error. I have tried pre4

I am new to this forum. As well as a new user of Asterisk. My vendor installed the system and we are still trying to get all the bugs out of it! I have a few questions about configuration and a program to view who is on what extensions. I am looking for a program that will work on my Receptionist work station. She is running Windows 2000 pro. We have not plans on upgrading to XP pro so

I have a question on SIP devices that are setup and working but you change the login name and contents to them why does asterisk need to be shut down and restarted for them to work? I have reloaded extensions and done a reload command. But the updated sip phones do not work until I shut down and restart asterisk. Is there any other way to update them without restarting the system? Since the

I have about 5 snom 200 phones working fine with everything. Voicemail, Transfers and all. Except I can't seem to use them to pickup parked calls nor place a call on park. I also have sipura-2000 with analog phones that are able to pickup parked calls and to park them. Most of them are on firmware 2.04g I have upgraded one to 2.05c for testing but this did not fix the problem. I get no error

I am trying to get a building that has 3 company's on one asterisk server. I need to make the IVR via DID take them to there right menu. So far I have everything working except when they goto via standard_marco to an extension and are sent to voicemail they are dropped off in the first menu and not the one they came from. In other word sent to another company's menu. If it happens to be

I have a problem in that when you use IAX2 for trunking and have 2 nics one is used to connect directly to 2nd Asterisk server how do we get the outside Nic card to take IAX connections? Is there any way to get this working via two paths? There is only one bindipaddr=10.1.1.1 for internal trunk but outside address section? -----------------------------------------------------------------

Thanks for that, I am however slightly concerned that due to the fast moving asterisk project (with new versions coming out regularly) that digium may start phasing out support for 2.4 kernel, I would like to settle on an OS for my customers and don't want to have to readdress the situation in one year because the 2.4 kernel is no longer the supported /stable version. Does anybody believe this

I have 2 Snom 200 and would like to get them to work properly with Asterisk. With the Firmware 2.02t I am able to use the phone. But only one line configured. With there newer firmware 2.03o it will not allow me to make calls. But I can get calls on the unit. Again the 2nd line is not able to be registered. Is this an issue with Asterisk or Snom? I could use some example configuration

Hello I am still having problems with IAXTELL and FWD configuration. I get the following when I dial 17009965342 which is set as an example to dial to FWD people. 1+700+99+ 5 digit number. I have placed XXXXX where my passwords are. CLI> Executing Dial("Zap/14-1", "IAX/abatista:xxxxxx@iaxtel.com/917009965342@iaxtel") in new stack -- Calling using options

Hello, Great job on the Asterisk@home project. Looks great this new version is really nicer looking. But I have a few questions. 1) For the new web access http://localIP/maint how and where do I change the password. 2) Since I don't use the Amp section for setup the .conf files I use my own. How do I get the asterisk server running status up. I have it running and works but shows up as not

Hi, we have samba server with version 3.0.6. we are facinga peciular problem. on unix machine the user and his group got full permission and others don't have any permissions (770) on a particular file . when he is trying to access it from windows he couldn't open the file. especially we are facing this problem with Microsoft visio (.vsd) and Microsoft XL (.xls) files. Eg: when

I try to connect to voipjet, but I get always busy, ... it worked yesterday, ... no changes on my side.... -- Executing SetGroup("SIP/615-829b", "iax-voipjet") in new stack -- Executing Dial("SIP/615-829b", "IAX2/17567@voipjet/011886228357765") in new stack May 20 18:16:26 NOTICE[9733]: app_dial.c:973 dial_exec_full: Unable to create channel

Thank you very much for the promptness of your response. blocking port 53 I don't think it's a good idea, at least in my situation, since for example I would have to open it in the future to be able to add new PCs to the domain. I don't know if the samba configuration files, overwrite within the zone configuration of my domain, who can query my DNS (I suppose it does), but I

Hello everyone, I recently updated to dovecot 2.0.19 (in fact, I updated the whole system to Ubuntu 12.04 LTS, I am using the dovecot from the Ubuntu packages) and just today found out that the dovecot-lda for some reason doesn't auto-create missing folders anymore as it did with my old installation (1.0.10). I have a "system users" layout and send my mails through a

Hello all, we're currently having problems with Windows XP machines that have *very* long file access times for files that are located on our linux-based samba server (samba 2.2.5 / linux 2.4.18). This happens with all kinds of files, with all kinds of programs, including Office97, text editors, develoment environments, etc. Sometimes - the incidents itself seems to be random and is not