similar to: HFC-S in NT mode, wiring?

hi all, i have a probably very stupid question/problem. for testing purpose i am trying to get asterisk running with two isdn cards. I'd only like to here the demo sound when i call the number - but nothing works. The output of show channels is not showing any channel - should there be 4 channels ? - capi info shows my two cards perfectly. The ISDN Controller's are attached to an PTMP

Hi! I'm struggeling had to get a hfc pci card working in NT-Mode. I've installed a very basic test system with just one hfc pci card connected to an ISDN-phone over a modified NTBA as described on jollies homepage. I commpiled asterisk as descibed in kape's INSTALL file that comes with 'bri_stuff'. I have not modified the config fieles yet. After connecting to asterisk by

hi, i just found a page on the net which might me worth some lines. for the urgent reader: http://isdn.jolly.de there is a guy in germany who has successfully programmed a gpl-patch for isdn4linux to make isdn cards with the hfc chipset from cologne chip (http://www.colognechip.com) run in the NT mode (up to 2.4.20). this mode is needed to connect isdn device to a pc and enables the use of

hi all! I'm running an Asterisk-box with bristuff-....RC8n and 2 HFC-S cards. I m located in Vienna/Austria. I have the problem that on outgoing calls i hear my voice as a short echo (about half a second). This occurs not on every call. I tried some changes in my zapata.conf, with rxgain and txgain settings, but to me its hard to find a configuration which is good for every call i make. Is

Hi, I'd like to realize the following setup traditional phones --> pbx (non ip ) --> asterisk --- ISDN network is it possible to set up an asterisk server in such way that it acts as gateway between a traditionnal pbx and an isdn network ( I'm in France ). this to let people continue with their existing pbx + phones and enjoy voip features ? outgoing calls: if yes,do I need

Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1

-----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Zoltan Szecsei Sent: zaterdag 16 juli 2005 12:54 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Multiple ISDN BRI Units with Asterisk usingBristuff zaphfc in NT mode? >> Maybe this is rather a hardware question,

Hi, I am looking for inexpensive isdn card that supports nt mode with asterisk. Does it mean that if mISDN has nt mode support for a specific card that asterisk has too? If yes, I presume I could buy any of the cards listed on the PBX4Linux page: http://isdn.jolly.de/cards.html Or will asterisk work ONLY with cards with hfc chipsets? Cheers, Arik

I've this error How i can find the problem? Apr 23 12:24:43 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:24:47 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:24:48 WARNING[131081]: PRI: !! Got a UA, but i'm in state 1 Apr 23 12:24:53 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:25:02 WARNING[131081]: PRI:

Hi, I am looking to integrate Asterisk with a Siemens HiCom 150e via BRI and wondered if anyone is able to offer any advice. In simplistic terms, my goal is to pass calls from the HiCom to the Asterisk box. e.g: HiCom user dials access code and can call Asterisk extension or establish SIP call over Internet. Likewise, I'd like Asterisk to be able to present a call to the Hicom, either

Hi All, The meetme.conf have created as below: [rooms] conf => 101 conf => 102 and extensions.conf as below: exten => _1XX,1,MeetMe,${EXTEN} why the warning printed when I called 101. WARNING[27660]: File pbx.c, Line 1051 (pbx_extension_helper): No application 'MeetMe' for extension (ipcentrex, 101, 1) And I found asterisk have not load the meetme.conf when it starts up.

so here it is, the problem that's been nagging me for the past 2 days: connected a box to my telco's NTBA <-> zap/asterisk. which works: box:/etc/asterisk# cat /proc/zaptel/1 Span 1: ZTHFC1 "HFC-S PCI A ISDN card 0 [TE] layer 1 ACTIVATED (F7)" HDB3/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In

Hello everyone. I've got this really annoying HFC Cologne card (or however I should call it - a single channel ISDN card based on the HFC chipset). It wrongfully detects lots and lots and lots of incoming DTMFs, to the point the card is not usable. Here's a sample out of CLI: P[ 1] I IND :DTMF_TONE oad:206361 dad:520101 P[ 1] --> mode:TE cause:16 ocause:16 rad: cad: P[ 1] -->

I have ISDN BRI line (Point-to-multipoint), with HFC card and bristuff/zaphfc driver. I also have TA attached to NT, with analog phones and modem on it. When I'm dialling through Asterisk/bristuff, and in the same time TA have some conversation (or maybe modem link) on channel 1, I can hear that conversation (or modem) very short period (0.2sec), and I also disturbing that conversation

Hello, I've been using * for quite a while using AVM C4 card and a few Grandstream Budgetone 102 hard phones plus couple of HandyTone 286. Echo is a big problem. I am getting used to it, but some users complain. Anyone has experience w/ regards to echo comparing the AVM C4 with two HFC-cards? Before shelling out time and money, maybe someone else already has done so, and could tell me if

hello, anyone has worknig ISDN hfc-pci card in DDI (DID) point2point mode? what kernel ? and second question mISDN driver .. anyone has working solution with mISDN and maybe fritz card? what you suggest for DDI -> point2point mode (card,kernel,chan_..., ...) ? thank you, Tomaz

Does any one put a HFC-S card working in nt ptp mode? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100221/ca845019/attachment.htm

Hi, I have built another Asterisk box using one ISDN HFC-S card and Bristuff-0.2.0-RC8p. But this time it behaves very strangely. Asterisk simply hangs and in logs I receive something like this: --NOTICE [1197]: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 --NOTICE [1197]: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 And when I want to call a ZAP channel I get

Hello everyone. I've got a HFC ISDN card that I'm using with chan_misdn and it basically behaves like crap. Echo is waaay worst then echo I get TDM400 card, sound is "choppy" (there other side is allays complaining about sound interruptions) and to top it all it detects fake DTMF's all the time. Is this a chan_misdn problem or is it a card problem? I really need to get

Hi, I have two HFC-s boards I configured in NT and TE mode respectively. When I connect the two boards together, I can dial extensions and I see the correct called and caller ID numbers: -- Executing SetCallerID("Zap/2-1", "7516862") in new stack == CDR updated on Zap/2-1 -- Executing Dial("Zap/2-1", "Zap/g2/0795025602|30|r") in new stack --