similar to: Question about dial out via Zap

How do I setup my T1 card as an E&M tie line? Any special configuration? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050523/8aac4dbf/attachment.htm

We have an old Telrad 128KSU PBX to which I am trying to connect asterisk in the following manner: Current Setup: Telco-> T1->PBX Desired Setup: Telco-> T1-> Asterisk-> T1-> PBX. I am first trying to setup the Asterisk -> T1->PBX part without disturbing existing setup so I can get asterisk to forward calls to PBX and once that is done, I would try to move the telco

Hello All, I've mostly solved my DID problem from a few days ago. Apparenly the lines weren't configured properly. Now heres the next question. 12 E&M wink lines from telco. I have them all plugging into an Adtran 750 with FXS cards. The Adtran ports are configured DPO. How do I signal this from Zaptel. I have them setup E&M in zaptel.conf and EM_W in zapata.conf. They

I am trying to receive both CID and DNIS from the telco through a non-pri T1. Currently I have the T1 setup and operational both outbound and inbound calls are completed as should be expected. The calls came in and were placed in the context specified in zapata.conf on exten => s,1. I have requested that the telco provide callerid (they call it ANI) along with 10 digit dnis for my 800

I have been getting quite a bit of PRI Resets using my Quad PRI Digium card. Prior to the resets I am getting similar notices to the following chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 3 Telco claims the PRI's are fine on their end and that it is my unit. Is this timing? (google somewhat leads to this) I am running 1.08 asterisk zaptel

Is it possible to control the dialing format used when making a call from asterisk separately from the inbound format? In my case I have a single robbed-bit T1 configured for featd (to receive ANI and DNIS) on a TE410P. This configuration works fine for inbound calls, however when an outbound call is made on this same T1 asterisk dials outbound in the featd format. I need asterisk to only dial

Hello Guys, I am trying to make Asterisk do dial-out calls. It doesn't even do test calls. It never calls. I tested everything and i am clueless. However i can call Asterisk and it picks up the phone and executes the dial-plan. However, my dial-plan is supposed to do outbound calls. Zap is configured correctly. I am using a TDM400 card from Digium with 4 Fxo ports and i have

Hello, I've got very annoying behaviour from our asterisk PBX. We have 12 channels T1 e&m wink start for TDM and using iax softphones internally (iaxcomm, but tried firefly-thirdparty and discarded for bad sound quality). Slackware 9.1 w/ kernel 2.4.26+ digium TE110P card. In some cases when call is placed from softphone to TDM, system does not detect call answered on Zap channel and

Hi all, I've just noticed I'm getting a load of these query_name_response: Multiple (2) responses received for a query on subnet 193.62.43.24 for name INFORMATICS<1d>. This response was from IP 193.62.43.39 In the log.nmb on one of my (several) Samba servers. I've not had a chance yet to check if it's happening on all of them. Most pertiant question for me is why is it

I have two Adtran 750's connecting our analog phones to asterisk. On occasion, I get a channel that gets "stuck" off hook. 'show channels' shows: Zap/27-1 (longdistance s 1 ) Rsrvd (None) (None) And will just stay like that until the phone is manually picked up and hung up again (or asterisk is stopped/started). I guess this is a function of an unclean hangup (being

I recently purchased a Sipura 2000 and connected a phone to it which is connected to my asterisk box via sip. Calls to the Sipura 2000 work fine from another sip device connected through *, from either an fxo or fxs (via adtran channel bank connected to a T400P card) port. However, when a call comes in from the phone company over a T1 with em_w trunks, the phone on the Sipura will ring but I

I currrently have Asterisk 1.2.8 with a TE110P Zaptel card tied to our Nortal DMS-10 switch via T1. This T1 trunk is configured for Feature Group D MF. The purpose of this is for LD delivery to a VoIP LD provider as a LD choice for our customers off of the DMS-10. When I sieze a channel on the zaptel, I get a spill of digits from the switch that is the called number, and I can see that in

I'm looking for a good web based voicemail client that can use mysql or realtime drivers. I can't seem to get vmail.cgi to work with realtime. Thanks for any help you can give.

"In general you can match callerID with the /, but if you don't put anything after the /, then the rule matches "no caller*ID", and if no slash is there at all, it matches "any callerid". " Ok.My question is -> how to match callerid from 001... ? and if don't know how many numbers ? exten => s/0_,Answer don't work- anything else ? tnx Thomas

Hello All, I'm trying to connect Asterisk to an Executone phone system with an analog DID card and I'm hoping someone can help me figure out what I'm doing wrong. The Executone DID card provides battery to the telco, when the telco wishes to dial a DID it goes off-hook, waits for a wink from the Executone and then dials the last three digits on the number with pulse (as opposed

So I'm not getting caller ID via the X100P card. I've confirmed the PSTN is sending me caller id by plugging in a little third party box. Ideas, tips, greatly appreciated

Not able to get the auto dialer part of asterisk to work with the zap channel. It works great with the sip channel. Here is the call file and the CLI output Call File Channel: ZAP/G1/6144994925 MaxRetries: 3 RetryTime: 40 WaitTime: 2 Context: amaxx Extension: 36652 Priority: 1 CLI Output Connected to Asterisk SVN-branch-1.4-r57207 currently running on VoIP-PBX (pid

Basically, have an old IVR application running under Apex's Omnivox software on a box with 4 old intel dialogic D240SCs, and would like to allow remote clients to gain access to aforementioned IVR application via softphone, 7960, ata, etc via asterisk with a TE410P. Unfortunately, all I know about the dialogics is that they're configured for D4/AMI, which I believe I have configured right

I search Google to find how to get the message light to flash on my Cisco 7960 running (Application Load ID POS3-06-3-00) (Boot Load ID PC03M030) (DSP Load ID PS03AT38) All I see is about the sip.conf file witch mine has the mailbox=XXXX but still no light. Also the messages button does not work. Any ideas?

Hello, Being totally fed up with the lack of quality and reliability from both VoicePulse and BroadVoice, We are switching to a direct IP connection to Global Crossing. We've installed a local point-to-point T1 into their CO, and they will give/take SIP g729a directly and act as the gateway for us. In setting up the inbound SIP service, they are asking the question, "In what format do