similar to: Isdn4Linux and DTMF

Well, it has been a long time since I used my NetJet S cards with asterisk (moved to the quad PRI card) but I am trying to get this working again for home use. Basically, what I am using is this: Linux 2.6.8.1: config lines: # ISDN subsystem CONFIG_ISDN=y # Old ISDN4Linux CONFIG_ISDN_I4L=y # CONFIG_ISDN_PPP is not set CONFIG_ISDN_AUDIO=y # CONFIG_ISDN_TTY_FAX is not set CONFIG_ISDN_DRV_HISAX=y

The card is an ASUSCOM ISDNLink PCI (passive) and the circuit is from Qwest (in the US). I will be using this circuit only for voice (I'm doing this because of the poor quality of my POTS lines). I've compiled Hisax (as a module) into my 2.4.25 kernel, and with 'modprobe hisax type=35 protocol=4 id=hisax' I get the following: Apr 7 10:34:24 dev kernel: HiSax: Linux Driver for

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm having some problems using the asterisk modem driver with an ISDN4Linux card (AVM Fritz). (I realise that it's better to use CAPI, but unfortunately this card doesn't have any CAPI drivers). Every so often the ISDN just stops working (it neither dials out nor accepts incoming calls). Trying to dial out just logs: --

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

Hello! Im pretty new of asterisk world: my goal would be using iaxcomm to call ppl over POTN. Yesterday i configured asterisk to be able to hear a song (with Playback() command) with iaxcomm, and it was wonderful. Now, today i tried to configure asterisk to use my ISDN4Linux supported card (a plain HFC card) with asterisk. i configured modem.conf this way, after reading

Hi to everyone! I am new to this list and i want to greet you all! I am trying to install Asterisk on a Fedora Core 3 Distribution with a Digi Datafire Micro V ISDN Card. I know that I have to use the ISDN4Linux so in modem.conf I set the I4l driver ,the msn and device. Modem.conf [interfaces] context=remote ;driver=aopen ; modem by AOpen driver=i4l ; isdn4linux - an

Hello, I just got my isdn-card working together with i4l and asterisk. Everything seems to be working fine: I can accept calls coming from the outside and I can dial out. Even setting the msn works like charm but my problem is that I cannot hear a word. There's complete silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network

Hi all, I'm playing with Asterisk and I've already configured all needed .conf files. It works quite well, but now I need your help to tune the system: when I place a call from a softphone to the PSTN, I can't hear directly Telco's tones and I can't use its services, e.g. a mobile's answering machine. I don't know if I have to modify the dialplan or if it depends on my

Hi. I'm working with i4l with asterisk CVS-02/21/03-13:59:12, plus i4l (chan modem i4l *dsp patched* and kernel 2.4.19 patched to disable dtmf). All seems ok (apart some echo issues that seems gone with mec2 aggressive suppressor), but outgoing dtmf doesn't work . or at least I hear the very first part of the dtmf, but then it seems suppressed. here's my modem.conf [interfaces]

I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing

Hi, Apologies in advance for the lengthy email. I'm new to asterisk and have trouble with isdn4linux. The setup is very basic like this: winxp ------- asterisk -------- winxp x-lite | x-lite | pstn The hardware involved is: Compaq EVO with RH9/kernel 2.4.20-30.9. Fritz!Card PCI v2 Asterisk CVS-04/17/04-21:36:18 Basically

I have asterisk loaded and seemingly working with 4 snom 200 phones. I cannot dial in or out using a DIVA isdn card When I dial out i get "not found xxxxxxx" on the handset. When I dial in i see in /var/log/message isdn_net: Incoming call without OAD, assuming '0' isdn_net: call from 0 -> 0 1856 ignored isdn_tty: Incoming call without OAD, assuming '0' isdn_tty:

Hi all, this is a rather "newbie-oriented" question, so please bear with me... The system running Asterisk has been provided with an AVM FRITZ!Card PnP. SuSE Linux 9.0 recognizes it right after booting the system and it seems to be configured (MSN) correctly... The hwinfo looks like this: --- pbx:/etc/asterisk # hwinfo --isapnp 11: ISA(PnP) 01.0: 10300 ISDN Adapter [Created at

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

Currently we have problems with our asterisk server connect with an Eicon Diva 4BRI Card to a PBX. Asterisk is running in version 1.0.0 on RedHat Enterprise Linux 3AS with kernel 2.4.21-4.EL. The Diva server is running in version 7.5 Can someone help us in reolving the errors with incoming calls? When we try to call to an extension we get these messages in the CLI: -- creating pipe for

Hello all, This afternoon I had a BRI line installed by Telstra (our telco in Australia). I'm using an Eicon Diva 2.02 PCI ISDN card with the isdn4linux driver. Incoming and outgoing calls with Asterisk work fine (and with no echo - my main reason for getting ISDN). However, I can't seem to get outgoing DTMF working (incoming works fine). I made a call from my desk phone (Cisco 7940G)

Hi, I currently use? Asterisk 1.0.7-BRIstuffed-0.2.0-RC7k on a debian sarge with a kernel 2.4.27 on a P4 3Gig with 1Gig of memory When i use i4l on any call, the called party ( on the telco operator side ) ear me with a delay of 1 sec after 1 minutes , 2 sec after 3 minutes and so on... After a quart hour, the delay make the conversation just

Hi all, I have this weird problem. I'm running asterisk 1.0.3 on Debian Sid (official debian package). We have 2 fritz ISDN cards. All is working great. Till I called the bank. It rings one time and then gives me the congestion tone. Here is what I see on the CLI (phone nr obfuscated for privacy reasons): -- Executing Dial("SCCP/michiel-00000004",

Hi, I currently use Asterisk 1.0.7-BRIstuffed-0.2.0-RC7k on a debian sarge with a kernel 2.4.27 on a P4 3Gig with 1Gig of memory When i use i4l on any call, the called party ( on the telco operator side ) ear me with a delay of 1 sec after 1 minutes , 2 sec after 3 minutes and so on... After a quart hour, the delay make the conversation just impossible !!! I use a tdm400P to connect my analogs

Hi *, This is my first message to this list, so I hope I am not breaking any rule with my post. My question is the following: can I establish a voice connection over an ISDN interface by using a bluetooth dongle to connect to the ISDN access point? Here follow the details: I have compiled and configured asterisk. Everything seems fine except that when I configure asterisk to use the ISDN