Displaying 20 results from an estimated 1000 matches similar to: "HELP with HFC Card, please"
2004 Aug 26
1
No signal from ISDN-phone connected to hfc card in NT-mode
Hi!
I'm struggeling had to get a hfc pci card working in NT-Mode. I've
installed a very basic test system with just one hfc pci card connected
to an ISDN-phone over a modified NTBA as described on jollies homepage.
I commpiled asterisk as descibed in kape's INSTALL file that comes with
'bri_stuff'. I have not modified the config fieles yet.
After connecting to asterisk by
2005 May 04
0
hfc isdn cards & zaphfc in domU
Hello,
After searching the archives, I''ve found only two messages regarding
this case, but there were no solution.
I have a similar problem, so I try to ask here.
I have twi HFC chipset ISDN cards in my pc:
0000:00:0d.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02)
Subsystem: Cologne Chip Designs GmbH ISDN Board
Flags: bus
2004 May 27
0
HFC-S BRI Slack9.1 kernel 2.6.6 "Guide" bri-stuff.0.0.2
Hi ""noobs"" and others(like me).
I've been struggling for hours,days,days,days.... to get my Asterisk work
with 2x HFC-S BRI cards.
One card for use in NT-mode for connecting my ISDN DECT phone,and one card
as gateway to PSTN.
Now it'works,and I just want to share some of the experience with others.
I'd guess there must be 'Somebody Out There' having
2005 Jan 26
0
HFC-S card problems
Hello everybody,
I'm having little trouble (well, pretty big trouble) with HFC-S card and
Asterisk. My idea is to do VoIP/IAX link between two HW PBXen using two
Asterisk PC boxen with ISDN cards in them. AFAIK HFC-S cards must be in NT
mode for this installation, they must behave like state line for those HW
PBXen. (if wrong, please correct me).
Diagram follows:
2005 Aug 28
0
hfc-pci/zaphfc: Asterisk hangs with signalling bri_net_ptmp but not with bri_net
Please forgive me, if I misunderstand the problem completely.
Following instructions in several german blogs, I want to configure
Asterisk with a hfc-pci card, an old NTBA and an ISDN phone
as a SIP device.
It seems that I have to set signalling in zapata.conf to bri_net_ptmp.
When I do this, Asterisk will hang if started with -vvvvc, the last
lines of output being:
[res_features.so] =>
2005 Mar 19
0
my hfc card does not like Siemens
Hello,
I tried to connect my Siemens ISDN 4170 cordless small PBX to the
asterisk with an Acer HFC isdn card but I have not seen any success. The
asterisk can see the card but no success to receive or dial a call. The
Siemens 4170 gives fault in all the handsets with trying to dial and
does not receives anything.
I have linux kernel 2.4.29, asterisk CVS-v1-0-03/12/05-17, zaphfc
2005 Mar 08
2
zaphfc error
I have some problems starting asterisk with a hfc card using zaphfc:
[chan_zap.so]Mar 8 17:53:06 WARNING[2447]: loader.c:258 ast_load_resource:
/usr/lib/asterisk/modules/chan_zap.so: undefined symbol:
ast_retrieve_call_to_death
Mar 8 17:53:06 WARNING[2447]: loader.c:391 load_modules: Loading module
chan_zap.so failed!
I'm using asterisk from debian/sid:
Asterisk
2005 Mar 06
2
Need help on * anf HFC.
Hi, I'm a newbie on * trying to setup an HFC card.
I'm locked for many days getting the all-circuits-busy. And no idea what
else to look for/how to diagnose.
I'm in Spain, I've tried changing many parameters on zapata/zaptelcong
with no luck, also NT & TE modes (honsetly, I've no idea what is).
Any clue will be very much appreciated!
I've installed *@home on my RH9,
2004 Nov 30
0
AW: zaphfc problem
Hi,
I solved the Problem:
the context defined in zaptel.conf:
context = zapincoming
was not in extensions.conf, so nothing worked. ( I assumend this context
is only necessary for calls from zaptel, not to it)
This may be a bug: in the verbose log I found nothing like "[chan_zap]
Could not initialize ..., due to ....", this had helped alot and had
saved alot of hours (-;
2004 Dec 19
1
BRI Error with zaphfc
Hi
I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has
cordless DECT extensions.
I have set up asterisk on FC3 with two HFC cards and I am using the latest
bristuff.
I am trying to use * between my ISDN line and my PABX.
One card is in TE mode and can receive and make calls OK. I can make and
receive external calls to a SIP phone.
I cannot get the other card to talk to my
2004 Dec 03
0
ZAPHFC, Asterisk does not load with signalling = bri_net_ptmp
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
<meta content="text/html;charset=ISO-8859-1" http-equiv="Content-Type">
<title></title>
</head>
<body bgcolor="#ffffff" text="#000000">
Hi,<br>
<br>
I am trying to get zaphfc running in nt mode with asterisk.
2005 Jun 16
1
unamble to dialout to mobiles and others "special" numbers
Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a on a Debian 3.1
The system is connected with an HFC card directly to the telco line
card is in TE mode
and signalling used is bri_cpe_ptmp
I am able to dial out some "numbers" and some not.
In particular it seems that i can't call mobiles and special telco
numbers like the information call center, emergency numbers,...
If i use a normal
2004 Aug 17
0
zaphfc in mode TE can't dialout (dialin is OK)
Hello,
I am trying to use a HFC-PCI (CCD/Billion/Asuscom 2BD0) card in TE mode
to dial-in and out with ISDN.
The problem is I can not get the card to dial out with a Zap channel.
Dial-in is working. I am using bri-stuff 0.1.0-RC4 (but tried also RC3
and RC2k). I tried all combination of "immediate", "overlapdial",
"pridialplan". I earlier also managed to dial out
2005 May 18
6
zaphfc troubles
Hi,
I'm trying to setup a small BRI ISDN <-> voip gateway.
The ISDN card is based on Cologne chipset, so I try set it up with zaphfc.
The versions i'm running:
kernel-2.4.27
Asterisk 1.0.7-BRIstuffed-0.2.0-RC8e
zaptel modules 1.0.7
zaphfc is from bristuff-0.2.0-RC8e
When I'm doing the insmod on zaptel, zaphfc, zaprtc:
Zapata Telephony Interface Registered on major 196
PCI:
2007 Aug 11
4
asterisk and telewell isdn hfc problem
Hi,
I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I
use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I
also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load
module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1
debug=1). So i want to test two cards and make loop between them. So one
card would be NT,
2005 May 25
7
zaphfc: empty HDLC frame or bad CRC received
Hi, i've downloaded/compiled/installed the bristuffed asterisk
Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a
and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine
with kernel 2.6.11. Asterisk works well if i configure the card using
isdn4linux.
I'm having problems dialing out (not tried the input yet).
This is the output from asterisk:
-- Accepting AUTHENTICATED call from
2007 Jul 24
0
mISDN & Asterisk 1.4: HFC-S card not responsive
Hi,
I have installed Asterisk 1.4 with mISDN with the
install-asterisk.tar.gz script from beronet.com. On my system I have two
cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to
work well with mISDN on my system from a previous installation.
Now however, the AVM card works well at first glance, i.e. it
"registers" incoming calls and works through the asterisk
2006 Feb 16
0
Lots of lost interrupts when running HFC ISDN card in NT1 mode
Hi,
I'm setting up an asterisk server with this hardware configuration:
AMD Athlon 1000 Mhz
256 MB ram
3ware ATA raid controller
2 * Ethernet controller
2 * ISDN HFC controller
One ethernet controller is connected directly to the internet (public
IP)
One ethernet controller is connected to the internal lan
One ISDN controller is connected to the public telephone network
One ISDN controller
2004 Jul 07
2
zaphfc and ASUSCOM working in the US
I finally got my ASUSCOM (Cologne chip) ISDNLink card working here in
the US.
When a call arrives, I get "Unknown IE 42 (Unknown Information Element)"
and "Unknown IE 21 (Unknown Information Element)".
IE 21 (0x15) is defined as Q931_CALL_STATE_SUSPEND_REQUEST. IE 42
(0x2a) is not defined in the code and I couldn't google it.
Is this something perculiar with ISDN in
2008 Apr 03
0
HFC-S ISDN cards in Xen3.0.3 DomU''s
Hi!
I just wanted to ask if anyone managed to get "ordinary" HFC-S ISDN
cards with the zaphfc driver running in a Xen3 DomU.
I am referring to this post (
http://lists.xensource.com/archives/html/xen-users/2007-04/msg00202.html ),
which perfectly describes my problem and I am therefore going to
simply copy-and-paste it here:
----------- snip ------------>
Hi,
I''m