similar to: [Q] DIDs

I am currently working on an Asterisk test system, and will be presenting a demo to the Board of Directors tomorrow night. I want to make sure I have all of my ducks in a row. The Asterisk system will be used to replace a Norstar MICS. The location has two PRI's coming in, with a few hundred DIDs. I know how to make * use the DIDs incoming, and I know how Nortel uses the DIDs. Now for the

Hi all, I've seen a couple of posts recently from people who are doing something with Asterisk and a T100P and a Nortel PBX. However it's not clear exactly what they are doing. Does anyone know if it's possible to use a T100P or T400P as a DSX-1 interface to connect to a T1/PRI CO module in a Nortel PBX? We have a Nortel Norstar Modular ICS PBX and I'd like to plug its CO

I am trying to integrate a Nortel Norstar system with an Asterisk service using a TDM04B card (4 fxo). So far everyting works from Asterisk to Nortel. The problem is when someone dials from the Nortel PBX to the Asterisk server. Asterisk answers the call and provides a dialtone (with DISA) but appartently the DTMF tones are not passed to asterisk and the call cannot proceed. This only

What models? Jeff Noxon (jeff-asterisk at planetfall.com) wrote*: > >I just purchased a bunch of Nortel Meridian POTS phones that support >intercom on the 3rd pair. I intend to get it working with Asterisk. >The phones support MWI, have a 3-line display, callerID, call waiting >callerID, 2 lines...very nice. > >On Thu, Feb 27, 2003 at 01:07:19AM -1000, James H. Thompson

Hey gang, I'm looking at escaping from a Nortel Meridian CISC system to Asterisk/Digium/SIP phones. I'm currently in the testing and proof of concept phase. I'm going to need a SIP phone and don't want to re-purchase and have "orphans" around. We currently run Nortel 7310 phones and they work great. I'm sort of overwhelmed by all of the different IP phones. I

To All; My current issues is a 5 second delay for call that is being transferred from the Norstar units to the Asterisk servers VIA a PRI. Is their anything that can be done to speed up the transfer on the Norstar. Below is my current phone config. < Norstar1 >----PRI----< Asterisk-1 >----IP-WAN----< Asterisk-2 >---PRI---< Norstar2> The Norstars are MICS 0x32 4.1

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I've searched the mailing list quite extensively, but didn't come up with anything promising (some things wer helpful, though). Does anyone know if Nortel M Series (specifically the 2008, 2616, 7208, and 7310) phones can be made to work with the TDM400P card or if they are ADSI compatible at all? I kind of doubt they will work if they are

I am looking at setting up the following configuration and any help/input/comments before signing the PRI contracts will be greatly appreciated. PRI Tampa PRI Sarasota PRI <--> Nortel BCM-->Asterisk<------------------>Asterisk<---> I would like to link the Nortel BCM to * using the a digital trunk card. The BCM will

Does anyone know which signalling protocol works when connecting the output of a NT8B90AL Norstar ATA2 analog terminal adapter to an FXO card? (fxsks, fxsgs, fxsls?) I'm trying to add an Asterisk branch to my Norstar PBX as outlined at http://www.voip-info.org/wiki-Asterisk+Nortel. - Mike

Has anyone integrated Asterisk for Voicemail with a Nortel Meridian phone system or know if this could be done? Thanks, John Haigh

Unfortunatly no on both counts. The arrangement right now has: PSTN Trunks & Stations <-> Nortel Norstar#1 <-CT1-> Asterisk#1 <-IAX2-> Asterisk#2 <-CT1-> Nortel Nortstar#2 <-> Stations The Asterisk boxes provide Voicemail to their sites Norstars and intersite calls over IAX. Local Voicemail works flawlessly at each site but there have been reports of PSTN calls

I have been investigating more tight integration between * and the Nortel MICS... it appears that it is at least theoretically possible to have * store voicemail and log which stations call where. Both require a T1 card. The T1 card requires either a clocking module or the 6-port fiber module to provide T1 timing. Naturally a T100P or TE405P is required on the * side. To log which

I am hoping to replace my Nortel 8x24 switch with Asterisk. Right now my cabling comes from my outside phone box into my office and into a punchdown block and leaves the punchdown block as an amphenol connector which currently plugs into the Nortel swicth. A second amphenol connector them plugs into the switch and extends to another punchdown block that I believe carries the lines throughout the

I have gone through some archive about Nortel MICS (Meridian ?)+ Asterisk Integration but I'm not sure whether same as my case . 70 telephone sets | | Nortel MICS 4.1 --------- Asterisk | PSTN I have read the David Gomillion's Guide and got the idea . However, my plan is slightly different from what he did , I need to use Nortel MICS to connect to PSTN (I

Hello, I am wondering if anyone is using the Nortel 2001 2002 or 2004 phones on their asterisk implementation. My local dealer says they are not compatible with any open source implementations. Is there a phone compatibility list somewhere? Cheers Cian

Hi all, I am going to be building an Asterisk system to replace the current aging (aged) Nortel Meridian system in a travel agency. There is already a voice T-1 in place and currently there are about 20 extensions in use. I would want to move up to about 25 extensions immediately and about 30-35 within the year. I am going to want IVR and voicemail, plus the ability to ring a group of

Hi. I had successful confiured my Asterix PBX, but now I need to connect it to a Nortel Meridian phone plant, I got a Digium T100P on the machine I got the Asterisk and I already connect it with the phone plant, I need to know what configuration do I have to do so the ip extensions can make calls to the extensions of my plant Nortel. And extensions from the Nortel plant can call ip extensions of

Question...I'm fairly new to Asterisk, but one location I'm looking at deploying Asterisk has an Option 11 in place already (it's actually in someone's HOME - long story). Does anyone know if it's feasible to interconnect the two and use Asterisk to interface with the other offices and lines, and merely use the Option 11 as a gateway to use the existing digital handsets

I have a PRI link up and running between Asterisk and a Nortel Norstar MICS v4.1 . I'm having a problem getting the textual Caller Name across the link from Ast to Ns, however numeric Caller ID arrives and displays fine. From Ns to Ast both elements come through fine. I'm forcing dummy values for testing using: exten => s,1,SetCIDName(Test) exten => s,2,SetCallerID(1234561234)

Can anyone point me to a reference or sample config for bypassing a nailed up (point to point) t1 between two PBXs with asterisk and a pair of t1 cards? Right now I have 2 Nortel norstars connected to each other via a leased line t1. I also have a solid 10mbps low latency microwave link between the 2 sites. My goal is to run an asterisk box at each end with a t1 card and Ethernet card to