similar to: OH.323 Dialout Problem

For the benefit of everyone, having H323 Configuration problem due to H245 Tunnel, check the h323 Config embeded at the end. Comment the offending line as under: ; ; Enable H.245 tunnelling (yes,no). ; h245Tunnelling=yes ; -----Original Message----- From: Tola Ogunsan [mailto:tolaniye@hotmail.com] Sent: Wednesday, May 25, 2005 1:03 PM To: Kanuri, Seshu (Company IT) Subject: RE: oh323 problems

Hi, I've oh323 chan installed and working to make calls from SIP to H323 devices. The problem is can no hear sound with the H323 device. I think this is some related with codecs o nat, because the H323 have one public IP from a different subnet from the asterisk box. If I use netmeeting in gateway mode, the call can be completed and I can talk with a SIP device, but in gateway mode I can not

Hello all, It's me again. I would like play with calls between a H.323 client and a SIP client through * inside my LAN. For that, on host 192.168.1.20, I use GnomeMeeting (GM20) and Asterisk; on host 192.168.1.25, I use SJphone (SJ25) as SIP client on Windows and I register into * with a username, no password. The 3 files oh323.conf, sip.conf, extensions.conf are in attachment. In the same

I wonder if anyone can help me? Am trying to terminate to H323 Vegastream. I'm using OH323 with little success. I can dial out and answer but voip end just keepings ringing and ringing. Thanks for any help. Neil Config file: [general] listenAddress=ALL listenPort=1720 tcpStart=10000 tcpEnd=20000 udpStart=10000 udpEnd=20000 fastStart=no h245Tunnelling=no h245inSetup=no jitterMax=100

I've complied the OH323 .so successfully and can easily receive calls from my H323 gatekeeper (using 711u), however it seems that all outgoing calls are refused and I'm getting "reason 23 (Temporary failure)" as an error code which I can't find documented everywhere. My H323 gatekeeper needs a 001NXXNXXXXXX to dial out to the PSTN even if I'm in north america (Montreal)

Hi, ALL: I install my oh323 channel driver following steps of http://www.oinko.net/astrecipes/index.php?action=artikel&cat=270174&id=10&artlang=en I works my asterisk well before install the chan_oh323.so. But after I do "make install" the oh_323, my asterisk crash and show me the following message (asterisk -vvvvvvc). Does anyone have any idea about it? What's wrong

I've configured Asterisk 0.7.2 to work together with Cisco ATA186 (SIP,G.711. RFC2833) and OpenPhone (H.323, G.711). But there is an issue while calling from ATA186 to OpenPhone via Astrisk - when I press any key on analogue phone connected to ATA, Asterisk shows following message: -- Executing Dial("SIP/519-3781", "OH323/62.213.36.100|20|Tt") in new stack --

Hi, I get this error when trying to dial an outbound extension from a sip phone: -- snip -- -- Executing Dial("SIP/2003-02d1", "OH323/3215435249@h323gk|20") in new stack -- H.323 call to 3215435249@h323gk with codec ALAW -- Called 3215435249@h323gk 0:33.283 H225 Caller:8143908 PWLib Assertion fail: Null pointer reference, file

Hi all, i have big problems to make a h323 call over the gatekeeper from my provider. The provider demanded following account data: H323 ID: XXX-XXX-XX-X DetinationNumer: XXXXXXXXXXX I have configured the oh323.conf following: gatekeeper=XX.XX.XXX.XXX alias=XXX-XXX-XX-X Isx the alias equal to the h323id ? And how i have to make a call with the dial app ? I have following config: exten

I have tried everything. to register with this gatekeeper to make and receive calls These are the details I received from the voip provider: protocol H.323 Gatekeeper Address - AVS@210.21.118.XXX Port - 1719 RAS - 53 Q931 - 80 h245 - 1722 RTP - 1722 Username - H323 I have 2 phone number/accounts with this gatekeeper that I need to register to. ID - HMA0200.10szxn-xxxx e.164 - 22xx2912

Folks! I would appreciate if someone could send me a simple working h323 configuration file oh323.conf that is part of asterisk@home installation. I have tried to use the oh323.conf content listed on WIKI but it is just not working as my H323 endpoint ( PA168 based ATCOM Phone) cannot register. I need a working example of this file for similar phone. Seshu

Hi, I want to configure * to use a gatekeeper for routing calls to H.323 endpoints. I imagine it will work like that: * (chan_h323) will query the gatekeeper where to terminate the dialed number and the gatekeeper will return the information for the h.323 gateway. after that chan_h323 will try to make the call to the gateway it has received from the gatekeeper. so instead of duplicating a

Hello All Anybody had used ooH323 for asterisk i using ooH323-0.7.2 and asterisk CVS may 2005. OpenH323 1.17.1 and pwlib 1.9.0 and GNUGK 2.0.2 audio is very good, better than SIP and IAX, but i have problem. how to router call from openh323 to outside PSTN. my h323.conf setting ; Objective System's H323 Configuration example for tvcti ; ooh323c driver configuration ; ; [general]

OOH323 Debugging Enabled -- Executing Answer("SIP/3513-090f7d40", "") in new stack -- Executing Wait("SIP/3513-090f7d40", "1") in new stack -- Executing DeadAGI("SIP/3513-090f7d40", "a2billing.php|1") in new stack -- Launched AGI Script /var/lib/asterisk/agi-bin/a2billing.php a2billing.php|1: line:58 - IDCONFIG : 1

Dear friends, I have compiled and installed h.323 in my asterisk. And I have a service from a H.323 VoIP provider who give me user, password and gatekeeper IP address. All configured. But when I start my asterisk i receive the following error and h.323 calls can not be making and/or receiving. [chan_h323.so]=> (The NuFone Network's Open H.323 Channel Driver) == Parsing

Hi, I am working on a H.323 project which involves GnuGk and Asterisk My current goal is to provide IVR functionality for the H.323 users which register through GnuGk(eg. call credit information) I have successfully built a H.323 platform using GnuGk - it uses SQL accounting and authorisation. Now I am trying to integrate it with Asterisk in order to provide IVR functionality as I already

Hi, I am trying to communicate H323 and SIP users. I have configured h323.conf, sip.conf and ooh323.conf. If I am using gatekeeper (gnugk) then I am able to call successfully to h323 users using SJphone. And same for SIP users also. But when I disabled gatekeeper and trying to call using gateway with sjphone then every time whatever number I dial the call goes to asterisk and some computerized

I'm trying to connect an asterisk server via oh323 to a Lucent iMerge. I patched the code due so that Lucent can handle asterisk's ver4 h323 http://www.voip-info.org/wiki-Asterisk+Lucent+iMerge+Configuration I can now successfully dial in to our company over multiple lines. The issue is when I dial out The first outgoing call connects to an outside user A The second call drops the first

Hi, I just installed OH323 Plugin and im now tryin to make simple Configuration to connect Openphone and Xlite to my Asterisk-Server. All works fine, i just wanna know if there's a better way to do it? Is there anything wrong with my Config? OH323.conf [general] listenAddress=0.0.0.0 listenPort=1720 connectPort=1720 tcpStart=10000 tcpEnd=20000 udpStart=8000 udpEnd=8005 fastStart=no

Dear Mailinglist-User currently we`re working with an IP-PBX, based on Asterisk, with SIP, H.323 and ISDN-Capabilities. SIP and ISDN works fine, but H.323 not. In our first test, we started to connect Asterisk to an Cisco IOS-Gatekeeper with the "chan_oh323" (version 0.6.5). We successfully tested in/egress calls without any problems. But when we started to connect our Asterisk