similar to: CCM <->(H323) <-> *

The hack below is for OpenH323, not Asterisk. This is not an Asterisk problem AFAICT. I am posting it here so that any other Asterisk user with a similar problem might benefit from it. I may or may not post it to an OpenH323 list, but since both variants of the H.323 channel in Asterisk use non-current OpenH323 versions, it may not be of any benefit to anyone anytime soon if I went that route!

Hello, I can use directed call pickup using pickup application (between sip, iax, skinny cals), but unable to pickup call that is ringing on phone behind h323 gateway (using original h323 channel in asterisk), is this even suported? thx PJ exten => _*7.,1,Pickup(${EXTEN:2}) console log, when trying o pickup ringing line 324 (h323), from skinny phone (953) -- Executing

Hi, I was able to work out SIP trunk between Asterisk and CCM 4.x without any issues. Whereas SIP trunk in CCM 5.x is not working with Asterisk. Asterisk is sending OPTIONS messages to CCM 5.x for which CCM is not replying. For the same reason Asterisk is marking it as UNREACHABLE. Anybody got Asterisk and CCM 5.x intergation working. How can I fix the problem which I'm facing with CCM 5.x?

Hi, I've got a CCM ( Cisco Call Manager ), with a Cisco Unity VM server and about 45 SCCP phones on the ccm, and 200 users on unity. we want to migrate all users to IP Phones to ditch our ancient phone system. I would love to get Linksys-Sipura SPA-941s for the 150 users not on IP phones yet and run sip to an asterisk server, but have their voicemail on Unity. these phones are $150 each,

Hi, I have the following config: [7960] <--skinny--> [Cisco CCM] <--SIP_trunk--> [asterisk] <--SIP--> [X-lite] Is there a chance to avoid the RTP stream from passing through the Cisco CCM ? I would like to have all RTP handled by the *. This is just a testbed, for a larger project. What I want to achieve, is actually this: [Cisco Phone] <--skinny--> [Cisco CCM]

Running Cisco Call Manager 6.1 and Asterisk 1.4. CCM is connected to a T1, Asterisk is running strictly VoIP over the network and using CCM as the trunk. Calls from the SIP phones connected to Asterisk work fine. They can call both external numbers and any Cisco extensions attached to CCM. Calls from CCM to Asterisk fail without any notification in Asterisk (and I DID have this working at one

Okay, another Cisco related issue (sorry!). Single Asterisk box at location 1. Single Cisco box at location 2, however the Cisco is also the PBX for location 3 (same physical machine, calls routed via VoIP). Trying to have Asterisk be able to call EITHER Call Manager location. The single SIP trunk in CCM (version 6.1 mind you) only allows a single device pool to be selected. So configuring calls

Does asterisk work with CCM as gateway ? When I trying call asterisk,I totally can't hear any sound. When call ohphone - works good. 10.0.1.219 is CCM, 10.0.1.207 asterisk. Trace messages here : -------------------- == New H.323 Connection created. -- Received SETUP message... == Setting up Call -- Calling party name: [5001,] -- Calling party number: [5001] -- Called party

The machine in question is a DL360 G3 R03 Xeon DP 3060-512/533 (part number: 322471-421). It's the first HP-branded model we've had so far (previously all Compaq branded). It has 1Gb of memory and a couple of drives on the on-board SCSI controller (setup for mirroring in the SCSI bios). No SMP is setup right now (doesn't get far enough to do anything with it!). In any case, this

I've got problem with connecting asterisk to CCM. Our side has Asterisk system other side CCM , ehrn i dial a number on other side channles created , connections established but nothing happend , just silence , and after some time busy tone. Sides sending ad reciving g711 codec , but we need that sides send and recive g729 (we have licenses) , if in h323 conf i try to : disallow=all ,

Hi All, I'm just posting this questions to both forums as its related to both. In hope to get some help on below issue: Asterisk 1.4.x CCM = 4.x CME = 4.x codec = g711ulaw Here is my setup: 600X Phones ----> Asterisk ---- SIP Trunk ----> Call Manager -----> CME -----> 461X Phones 461X Phones ----> CME -----> my dial peer points to Asterisk IP for 600X Phones so in

Hi List, I have a system that connects into Asterisk 1.4.41 using CISCO CCM 7. Everything works great except when a call is transferred to the operator. The call goes to the operator via a native bridge and is completed, then a "phantom process" starts and tries to launch a new call every 15 minutes. I modified the dialplan to hangup these phantom calls, but no still

I have experience problems like this in a different scenario. It is usually due to codec translation problem. What is the default codec set on CCM for the IP Phone and the default set in Asterisk? Make sure the defaults are the same. Try G.711 Michael

Hi, trying to build the h323 channel driver that comes with asterisk works fine, but only as long as I use openh323-1.11.7. Unfortunately, that setup seems to have a bug which misguides one of the audio streams. (So while * can "hear" me, the phone remains silent.) I suppose that bug is fixed at least in openh323 CVS. At least, I got things mostly working using the external

Hi! I'm trying to communicate a Cisco CCM 4.0 with Asterisk 1.2.11, I 've followed the info in http://www.voip-info.org/tiki-index.php?page=Asterisk+Cisco+CallManager+Integration but still not able to make Asterisk communicate with Cisco. I keep on receiving --- SIP/2.0 400 Bad Request - 'Malformed/Missing URL' --- and --- SIP/2.0 404 Not Found --- messages

Successfully hooked up a Cisco CallManager to a local * installation via H323. Things are working fine when dialling from CCM to *, but I'm seeing a callerid of 'root' coming up on the CCM Phone when dialling into *. Is there any way of setting this to be something else? I'm guessing the name is coming from the ID that * is running as. I'm using the chan_h323 driver and

Hello: Does anyone know how to configure any of the Cisco 79XX phones to get custom ringers when using chan_sccp with Asterisk? I've currently got Asterisk's 05-24-04 CVS-HEAD and Zozo's 0.2 release of chan_sccp. I've tried using ringlist.dat, but that appears to only be for the SIP phones... Thanks for any input, Andrew

Hello all, Downloaded, compiled and installed Asterisk CVS-04/15/04-17:54:5. Everything looks fine except I see a pseudo channel in the 'zap show channels'. xxxx*CLI> zap show channels Chan Extension Context Language MusicOnHold pseudo default 1 default The result is, I cant use Zap/g1 in extensions, eg this doesnt work anymore: exten =>

Kevin Walsh noted that his SPA-2000 takes time from his local NTP server in a post back on Fri June 25. Q: Where do you tell it to use NTP? I'm a bit confused as to where my SPA-2000 is currently getting its time. I told it GMT-5 in the misc section but it doesn't really tell me where its going for this. Is it just broadcasting looking for ntp? The net of my problem is that it is 1 hour

Hi, On Friday we changed our Telco-Provider (from German Telekom to Mnet) and recieved new Numbers. I changed the extensions in extension conf to match the new numbers. But i always get: Jul 18 12:10:39 WARNING[245776]: pbx.c:1780 ast_pbx_run: Channel 'CAPI[contr1/89064934]/0' sent into invalid extension 's' in context 'default', but no invalid handler I only changed the