similar to: Which is PCI HDLC Chip used for TE405P / TE410P / E100P ?

I just upgraded my asterisk install from january 2005 CVS HEAD to current CVS HEAD : * zaptel * libpri * asterisk My asterisk have one TE405P with one span (the clock source) pluged into a telco PRI E1, a second span is a PRI E1 to another PBX and the third one is a T1 to a rhino channel bank. Everything went smoothly except that the two PRI span restart every ten seconds after some HDLC

Is there anything to choose, in performance, between a TE405P and a TE410P? I understand the difference between the PCI bus voltages, and certainly don't intend to try Andrew's hacksaw operation :-). But if I choose the card first, and a compatible mobo second, does it make any difference which? Cheers Tony -- Tony Mountifield Work: tony@softins.co.uk - http://www.softins.co.uk Play:

Can anybody tell me the difference between a TE410P and a TE405P? Is it JUST the 5v vs 3.3v pcis slot spec, or is there some thing else? </edg>

hi, after stumbling over the compile time flag in zaptel and after reading the new features of the 2nd generation firmware of the TE405P/TE410P, i was wondering if the cards are capable of upgrading the firmware in field? regards frank

Hello, Can anyone out there confirm as in "Yes I am doing this right now" that this can be done? I know that the stuff from 2.6 was backported to 2.4.26 - and it works there (so says the wiki) but before I buy a bunch of hardware (or don't buy hardware, depending on how you look at it) I would love to know. Thanks! -- Kristian Kielhofner

Dear All, we have installed a TE410P card on a Dell Poweredge 1750 running a slackware 10 with 2.4.26 Kernel. Then we have made two loops on the card and we have configurated all the 120 channels. Our goals was to perform some stess tests even if in this scenario we used the same box as generator and target. The stress test comprised to generate up to 60 calls at the same time by placing a file

Hello I've got small PBX (30 simultaneous connections) based on asterisk (1.6.2.6), which uses Stargate 2N ISDN to GSM gate. It runs ok for day or two, but then I get: dahdi: HDLC Receiver overrun on channel TE4/0/1/16 (master=TE4/0/1/16) in my kernel logs, in asterisk i get: pri show spans PRI span 1/0: Provisioned, Down, Active PRI span 3/0: Provisioned, In Alarm, Down, Active (span 3

Hi, Thank you. I will try it. Do you know some G.72x, GSM, and iLBC optimized for Blackfin ? I mean open source. -- Best regards, Miroslav mailto:miro@space-comm.com Wednesday, March 23, 2005, 9:05:11 PM, you wrote: JMV> Hi, JMV> As far as I understand, the last patch (for TI C5x) I merged in SVN also JMV> allows Blackfin to work, but I haven't

Hi, I would like to find some way for hardware coding instead software (using the Host CPU). Are there any PCI boards just with codecs (DSP) or other way? Best Regards, Miroslav Nachev COSMOS Software Enterprises, Ltd. Tel: (+359-2) 983-32-62 Mobile: (+359-88) 897-31-95 E-Mail: m_natchev@yahoo.com miro@space-comm.com http://www.space-comm.com

Hi, I can't find anywhere on the Asterisk web the license terms for commercial use of Asterisk software. Do I have to pay something (and how much) if I want to use the Asterisk in our IP PBX solutions? Best Regards, Miroslav Nachev COSMOS Software Enterprises, Ltd. Tel: (+359-2) 983-32-62 Mobile: (+359-88) 897-31-95 E-Mail: m_natchev@yahoo.com

Hi, We have potential client which would like to offer to him VoIP solution for 2000 subscribers (SIP based Phones) and 2 x PRI ISDN interfaces to the PSTN. In the next stage the subscribers will be increased up to 13,000. Because I am not haven't done similar big project I don't know how to calculate the price. The one way is using number of subscribers and the other is using PSTN

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

Hi, We currently have an Asterisk box (P4 2.4 Ghz, 512Mb RAM, 1 T100P, Zhone Channel Bank and 1 E100P) connected to an ISDN running without any problems. That machine is working for about 1 year. Two days ago, we decided to switch that machine for two PowerEdge 600SC (HA) and we got some problems. The running machine (P4 2.4Ghz) has an Intel motherboard with four 32-bit 3.3v PCI slots,

Hi, Are there any optimized codecs for Analog Blackfin DSP? If yes, from where we can download it? We are looking for Speech, Audio and Video codecs. Best Regards, Miroslav Nachev

Hi, I would like to ask you for advice how to solve the following case: I have a client (who happened to be my friend) and I have convinced him that the IP PBX solution is much better than the conventional telephone centrals (PBX). At the beginning he wanted to buy PBX Panasonic, but at this moment he is waiting for my decision. Because at the moment we are not so deeply familiar with these

I successfully installed asterisk@home 0.6, but when i try to load the wct4xxp module for the TE405P I just got, I get the following: Found TE410P at base address fb7ffc00, remapped to e0220c00 TE410P version c01a009b Tried to load 1c8ac800 into 00000000, but got 188ac800 instead Tried to load 1c8ac000 into 00000001, but got 188ac000 instead Tried to load 07fc07fc into 00000002, but got 03fc07fc

Hi, We have a case where we need of 16 x FXS, 12 x FXO and 1 x E1. To do this using Digium products I need of 8 PCI slots. This is not possible to be done in one computer and that's why I try to start using TDMoE. Unfortunately all my tries are without success. The network is crashed everytime. Can you give me some ideas/suggestions how to solve this case? Best Regards,

Hello, We have finished our tests of the new Digium firmware on the quad T1 cards(TE405P/TE410P). Overall it is a big improvement over the version 1 firmware. Here's the review: http://astguiclient.blogspot.com/2005/09/digium-405p-v2-review.html MATT--- -------------- next part -------------- An HTML attachment was scrubbed... URL:

I anyone has any hesitations in upgrading their 405P (or 410P) to V2 of the firmware, read below; I installed one today (turnaround time around 2 weeks to Australia, inc. economy freight in both directions... impressive!) and have noticed immediate, significant improvements. Audio levels are better (have set tx and rx gains back to 0.0) and missed frames have gone (popping, clicking,

I have 2 servers, configured identically. Each has a TE405P and 2 PRIs. One server was experiencing crackly audio on one circuit, accompanied by HDLC bad FCS messages. The telco recabled and moved me to another port on the DMS-100. The audio is better, but there are still bad FCS problems on the span. I have moved the PRI in question to the other server, and the problem does indeed move with the