similar to: incoming caller doesn't hear rining.

Hi, Urgently response would be wonderful, system is a Fedora Core 2. I have a Ericsson BP250 connected to 1 port on the TE405P and another connected to a local telco ISDN30. I have been running CVS-HEAD from about a 2 months ago and upgraded it again just in cause it was a version issue (didn't fix it) but this is what I am getting. When a person calls out from an extension on the BP250 to

Hi, Are there any hardware for ISDN30 ? if yes any problem with this ? is i out-of-box like ISDN2 but with 30 linies ? Do I need more than the cable from my teleprowider and a PCI-card ? /HHA _________________________________________________________________ Find high-speed ‘net deals — comparison-shop your local providers here. https://broadband.msn.com

Quoth Jon Morgan <jon.morgan at motors.co.uk> > >We have a 2 port Digium TE220P card, one span is configured to connect to our ISDN30 provider (British Telecom), the other span connects to our internal PBX. Here's the zaptel.conf snip: > >span=1,1,0,ccs,hdb3,crc4 >bchan=1-15 >dchan=16 >bchan=17-31 > >span=2,0,0,ccs,hdb3,crc4 >bchan=32-46 >dchan=47

My employer wants to use Asterisk, but the E1 circuit providing the current phone system is DASS2 rather than ISDN30. Converting the E1 to ISDN30 is not a practical proposition at this time as it'd stop the legacy phone system from working. Is there any sort of hardware support for DASS2? I speculate that the E100P should be able to deal with the electrical side of it, but I'm unsure of

I am running * with a Junghanns quadbri that should allow us to integrate our ISDN house telephone system with VOIP. Preferably I would like to run a setup, so that our internal ISDN phones on an S bus are not aware that * is sitting in between. With the configuration below I run into the following problems: 1. On outbound calls, I get the normal rining call progress tone althought the

Hi all, I've done this a few times with other PBX's but swyx has stumped me! I'm having some trouble getting Asterisk connected to a Swyx system using a sangoma A104dx... currently the setup is: BT <-> Swyx The above setup works fine... what i'm trying to achieve is BT & SIP Trunks <-> Asterisk <-> Swyx I have connected to our BT (2 x ISDN30 UK) with

Hi All, I recently upgraded from a very old stable to HEAD. For some reason, incoming callers don't hear ring tones when calling in. Everything else is working fine. Where should I look for a fix? ISDN --> E100P --> asterisk --> sipphones. Thanks Johan

Hello Im from Denmark and i've just got my Digium TE405P. But i have some problems when i connect it to my E1 connection (ISDN30). My telco delivered a alcatel box witch have a G.703 120ohm (DB9 with a serial to rj45) and a 75ohm coax connection. I've tried to connect using the 120ohm with rj45 and a ordinary utp cable. But it dosent seem to work. I've tried several zaptel.conf

Hi ! I am trying to configure two E100P cards, but I am a bit confused with zapta.conf in what I am trying to achieve. The * will be connected to a pstn switch with two E1 PRI lines. The E1 lines will be used for incoming calls as well as outgoing calls. My problem now is what to put in zapta.conf, I would like to group all channels from both cards together (if that's possible). Does this

Hi all I wonder if anyone can give a little insight into this; asterisk@home 2.2, HP Proliant gl3, sangoma A101,Cable and Wireless, ISDN30. 10 zactive channels Incoming calls work fine no problems tested 43 DIDs all working. zaptel.conf # Global data loadzone = uk defaultzone = uk span=1,1,0,ccs,hdb3,crc4 bchan=1-10 dchan=16 zapata.conf [channels] language=en context=from-pstn

Hello, I have a Sangoma A101 connected to an ISDN30 (E1 in the UK) with some Snom 300 and Idefisk softphones. I can do SIP and IAX2 calls just fine, however I cant get any audio in either direction on the Zap channels. When I call in or dial out over the ISDN30 (UK E1) I can see the call answered/placed on the CLI and then silence follows. I've been provisioned 25 out of the 31 channels only

On how to even search for this "feature" as I have no idea on what it can be. I've got a meridian linked to * (by EuroISDN) which is linked to a ISDN30. I can make calls from the meridian, and receive calls into the meridian. Great stuff. However, if someone dials an invalid number, then instead of hearing a "three tone", the line just drops and goes dead. The console

anybody recommend a supplier in the UK for a pri/isdn30 line (other than BT) thanx very much __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

I am running Asterisk 1.0.9 and have been running all my calls through a VSP over a IAX2 trunk however we have recently purchased and connected a TE110p to a PRI ( E1 with 16 voice channels ) through Optus. I can make outgoing calls via it fine, however incoming calls are dropped after a few seconds ( or as soon as a command like Playback, or the call is picked up if forwarded to a SIP

Dear Customer Support, i connected the asterisk to a e1 interface of our hipath4000. outgoing calls from a sip peer of my asterisk to an up0 telephone which iss connected to the hipath4000 are working. If you want to dial from an up0 device to the e1 interface where asterisk is connected to, you have to use the prefix 83. But when you enter the 3rd cipher this error appears at the cli

Hello, I'm having problems making international calls from our asterisk using an ISDN30 in the netherlands. Below is the zapata.conf that works for all national calls, but international calls all fail a RC=41 ; zapata.conf [trunkgroups] [channels] language=nl signalling=pri_cpe switchtype=euroisdn callerid=asreceived ;pridialplan=unknown ;prilocaldialplan=unknown immediate=no

I have a couple of numbers that are diverted to a number that is conected to an isdn30 card, running asterisk 1.4. eg. 123456 => 22334455 654321 => 22334455 What I would like to know is the number of the orginal number dialled (123456 or 654321). I thought that RDNIS was the answer, but it is always coming up blank. When I did a debug on the pri span, I saw the following message

Dear all I have confusion how to asterisk genrate tone and what ringing code use default 180 or 183 i have setup asterisk with mediant 2000 with avaya [asterisk]-----[mediant 2000]--------[Avaya] when i call from avaya side to ---> asterisk i don't got ringback Sound so how to asterisk genrate tone for calling party is there any soution and what is the problem of

Advance apologies for the length of this mail; I have an ISDN PRI supplied by NTL (ex Diamond Cable, Nottingham) which is currently working happily with an SDX Index phone system. I have to replace this phone system shortly and I've been trying to get a * system working for some weeks now. I have configured the dial plan (which works) and all my SIP extensions (which all work) along with

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --