similar to: Strange RTP audio errors on console

Hello Everyone, I have a new problem where when placing the call, asterisk will automatically go into music on hold until the call is connected (ie, no ringing). It was kind of confusing because sometimes `SESSION PROGRESS` takes longer than others, during this time we are in MOH. The call does eventually connect and the MOH stops. When debugging I saw the following debug message: [Sep 10

Hello! I'm facing completely choppy sound. The wireshark trace shows, that there are a lot of codec changes without any trigger (means no options or reinvite or any other package). Background: The call is initiated by asterisk and is received by the same asterisk conference room via Phone extension -> asterisk -> provider A -> provider B -> asterisk. Asterisk initially sends

Hi all, I seem to only be getting (1) call to sip_write() in channels/chan_sip.c I have a very simple setup. one server (no cards) 2 polycom IP 330 phones. Server is 192.168.1.150 and phone is DHCP. Nothing else on the network. No firewall is enabled. I call into the dialplan with: exten => 112,1,Answer exten => 112,n,Playback(demo-congrats) exten => 112,n,Hangup I see this executing

Dear All, I just setup the Asterisk with E100P which it's no problem in Dial In but I have problem when outdial. The connection method is like this : E1 PRI <-SIGNAL-1-> MaxLink (PBX) <-SIGNAL-2-> E100P <-> Asterisk <--> SIP \-----> Analog PHone Now when I tried to dial out by SIP X-Lite on Windows, it shows me Connect, Trying,

Hi, I have licensed the digium G.729A codec. But for some reason incoming and outgoing calls will ALWAYS use G.711a. When I force my phone to only accept G.729 then an incoming call from ZAP goes straight to my voicemailbox as the phone doesn't accept the codec Asterisk wants, even if I force it in sip.conf. Is there anywhere else I need to look to tell ZAP to use G.729 preferrably ? The

Hi, I am trying to replace my Cisco 5300 gateway with my new Zap TE405P card. Incoming calls and outgoing calls between my cisco and my SIP phone works fine on G.729. Recording messages in the asterisk voice-mailbox also works fine from both my SIP phone as well as PSTN -> Cisco -> Asterisk. I have licensed the digium G.729A codec. When I connect my ISDN PRI to my Zap card and I call

so, is it safe to put canreinvite=yes on a 7960? on a 1750? on a spa-x000? an xten? how the heck do i find out other than the hard way? randy -- ps: pun intended

Guys, I've been poking around trying to find a good answer for this via voip-info, google, etc... Haven't found anything that helps, so maybe you mates could. A lot of my customers are using Linksys UAs (router/ATA PAP2) and some using Sipura SPA-2002s. Every once in a while, the customer will get one-way audio. I've read that this is commonly caused by the outgoing RTP port not

Hi folks, In an effort to save bandwidth (our 7905s run over a WAN) we've switched from ulaw to g729a. We purchased 4 licenses from Digium (4 SIP clients, low call volume), and they seem to have been accepted: [codec_g729a.so] => (Annex A/B (floating point) G.729/PCM16 Codec Translator) == G.729 Host-ID: 07:53:aa:d3:e2:f2:bd:cc:27:60:9d:5f:da:eb:5d:e9:6e:09:a1:4e == Found license

I have a pretty basic Mandrake 10.2 w/KDE 3.2 and I installed Asterisk-1.0.1-2mdk. I installed the source of main and contrib from ftp, so at the install time I accepted all the packages needed to be installed too. The installation went smooth, but when I try to execute asterisk (#asterisk -vvv) I encounter few warnings I end with an error. At this point I didn't touch any conf file, I was

Hi, everybody: I have looked at the Polycom entries on www.voip-info.org, and they're outdated and convoluted and full of errors. All I want to do is get my Polycom 501 to register with a working Asterisk server. I want to do the configuration locally on the phone through the console. (The server works with an Xten X-lite softphone.) Has anyone done this? What do I need to do? Thanks,

hi, I'm currently trying to use Speex with Asterisk from my OpenH.323 client. It seems to mismatch the codecs, below is my log from Asterisk. My Openh323 client crashes in responding to a Speex request for bits per frame. I'm guessing it either isn't running the codec correctly or doesn't support the same subset of speex codecs as openh323. (I'm using speex-1.0.1 with

Alright, folks. I just deployed * into full production at my office. We have around 50 7905's, 5 7940's, and a handful of soft clients. We run a call center with around 15 agents. I also have a queue set up for the receptionists so that they don't get bombarded with calls. Everything seems to be working with a very few minor glitches. I firmly believe that the few problems we are

I rewrote scatter.smooth to handle missing values, but I have a question about a move I had to make. Here's the code: Mscatter.smooth<-function (x, y, span = 2/3, degree = 1, family = c("symmetric", "gaussian"), xlab = deparse(substitute(x)), ylab = deparse(substitute(y)), ylim = range(y, prediction$y), evaluation = 50, ...) { if (inherits(x,

HI ALL. Please help. Problem: video calls drop after 15-20 seconds all the time. Use * latest cvs. from sip.conf [1102] type=friend username=1102 host=dynamic callerid=Veo webcam<1102> canreinvite=no disallow=all allow=gsm ;allow=ulaw allow=h261 allow=h263 from iax.conf [peer2] ; 192.168.0.7 type=friend port=4569 auth=md5 secret=second2 context=local host=dynamic qualify=yes trunk=yes

Hello, I have that problem with codec G729. Please can somebody help me! WARNING[16384]: File codec_g729b.c, Line 413 (load_module): Unable to initialize va stuff: -1 == Detected 4 licensed G.729 transcoders WARNING[16384]: File translate.c, Line 219 (calc_cost): Translator 'g729tolinb' does not produce sample frames. == Registered translator 'g729tolinb' from format G729A to

Does anyone currently use Vonage with Asterisk? I've tried to set it up but it looks like Asterisk (at least the version that I have) does not handle well the SIP call dialog, sending a BYE with the wrong tag. As a result, when I hang up, Vonage sends back a 400 Bad Request and the call on the PSTN side does not hang up. I know that Vonage does a lot of nasty stuff which impacts UA's

Same here Michael and the PocketPC version seems unaudible with any codec; early days trying that though. Simon -----Original Message----- >From: "Michael Van Donselaar"<mvand@neb.rr.com> >Sent: 22/04/03 04:10:24 >To: "asterisk-users@lists.digium.com"<asterisk-users@lists.digium.com> >Subject: Re: [Asterisk-Users] Xten - Free windows SIP

I have a tdm 3xfxs and 1xfxo, aslo I have a setting with 1 snom 190 and 2 xten line. I can call from the snom to the ptsn line at the fxo port ok. I can call from the ptsn to the xten lite phone. I can call from the xten lite to snom but what I CAN`T do is; Call from xten to ptsn. When I dial from the xten, I can hear the dialed party, but he cannot hear me... Tips? Help? What I'm

Hello, Can somebody tell me what does it means ? I just installed my codec g729 with two channels. [codec_g729b.so] => (Annex B (floating point) G.729/PCM16 Codec Translator) == Detected 2 licensed G.729 transcoders WARNING[16384]: File translate.c, Line 219 (calc_cost): Translator 'g729tolinb' does not produce sample frames. == Registered translator 'g729tolinb' from