similar to: echotraining on T1 circuits

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

Has anyone seen this problem before? I have a server with a single X100P card. The audio level is a low, but if I raise the gain to more than -2db (Rx + Tx) it starts to oscillate in an echo test. Not at a high frequency but with a noise that is best described as a steam engine starting up. It then starts to clip and crackle. If I bring the gain down to Rx=-2.0 and Tx=0.0 or lower then it settles

I recently purchased a Sipura 2000 and connected a phone to it which is connected to my asterisk box via sip. Calls to the Sipura 2000 work fine from another sip device connected through *, from either an fxo or fxs (via adtran channel bank connected to a T400P card) port. However, when a call comes in from the phone company over a T1 with em_w trunks, the phone on the Sipura will ring but I

Hi All, I have installed a Digium TE110P card on an Asterisk 1.2.1 system. Its connected directly to the PSTN. But I am unable to make outbound calls on the zap channels. The light on the card is green. Asterisk CLI shows all 24 channels when I give the command 'zap show channels'. I also noticed that Asterisk CLI shows an incoming call every few seconds on the 24th channel. This must be

I'm trying to send a fax to my asterisk box, however shortly after connecting the fax machine reports a "communication error" and hangs up. Below is the error I get from RxFax: Fast carrier training failed Nothing is written to the file system as far as the tiff is concerned. Any ideas on how to fix this? Thanks ---- Sending Fax Machine: HP PSC 2000 Series 2210

Basically, have an old IVR application running under Apex's Omnivox software on a box with 4 old intel dialogic D240SCs, and would like to allow remote clients to gain access to aforementioned IVR application via softphone, 7960, ata, etc via asterisk with a TE410P. Unfortunately, all I know about the dialogics is that they're configured for D4/AMI, which I believe I have configured right

Has anyone here used T1s with RBS with asterisk? Cary Fitch

Hello, I have a T1 (not PRI) plugged into my Asterisk server. Everything is working well, except I only get the first digit of the 4 digit DID in Asterisk. The T1 provider (Eschelon) tried switching to 7 digits, and I only got the first digit of the 7. Can anybody help? We're adding another DID and I need to trap it correctly. Thanks. Here are snippets from the relevant files: --

I am having trouble getting transfers to work when a zap channel is part of the call. I have a couple SPA-2000's and some X100P cards as my setup. This is what I'm trying: Dial number from phone: -- Executing Dial("SIP/206-2c61", "Zap/1/#######") in new stack Currently on call: -- Called 1/####### Press flash to place call on hold with SPA-2000: --

Over the last couple weeks I've tried everything I could get my hands on in an attempt to get rid of my echo problems. Using a CVS checkout of just yesterday, I've tried every echo cancellation routine in zconfig.h (including Mark2 w/Aggressive) , as well as the echotraining=800 mentioned on this list just last week. While some things worked better then others, I would consider none

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make

Hello, I've seen various suggestions thrown around for hardware when people ask, but can we all agree on some basic hardware recommendations for a few basic setups(and post them on a website) to make it easier for new people to avoid some of the hardware/software pitfalls when they are setting up their first systems. Something like this: (THIS IS JUST A PROPOSED LAYOUT SO PLEASE BE GENTLE)

Hello list, (Resending this email due to a typo in previous copy) I need to do E1 to T1 conversion for a project, and was wondering if there exists a card with both E1 and T1 on it. Or is it possible to use two separate cards in an asterisk box, one for E1 and one for T1? (Please don't mention aculab or adtran, dealt with them in the past, won't deal again.) I talked to Digium and the

Hello, I've got very annoying behaviour from our asterisk PBX. We have 12 channels T1 e&m wink start for TDM and using iax softphones internally (iaxcomm, but tried firefly-thirdparty and discarded for bad sound quality). Slackware 9.1 w/ kernel 2.4.26+ digium TE110P card. In some cases when call is placed from softphone to TDM, system does not detect call answered on Zap channel and

For an inbound call center with 4 T1s and 30-50 agents on you would do just fine with a single, one-processor machine. We have handled more than this on a single P4 server although we use astGUIclient instead of Asterisk queues, but the load is very similar. I would recommend a Sangoma Quad T1 card because they are about 30% more efficient than Digium T1 cards. When you say that you need to

I have a couple of questions about Digium's T1 cards, such as the TE410P. Any answers would be greatly appreciated. 1) Do they support standard T1s or are they ISDN-only? 2) Do you know of anyone offering support for configuring T1s for Digium cards, and if so at what cost? Thanks, Matthew Roth http://www.voip-info.org/tiki-index.php?page=Running%20Asterisk%20on%20Debian

Hello, We use all SCSI PCI card hardware RAIDs on all 4 of our production Asterisk servers. They all have Digium quad T1 cards and they all have from 2 to 4 T1s hooked up to them. We have had no noticable problems with dropped calls/poor quality. What are you looking to do with this system? what kind of traffic will be going through these 4 T1s? MATT--- -----Original Message----- From: Deon

Are you looking for local or Long distance? What will these T1s primarily be used for(inbound/outbound, domestic, local, long distance, international) How important are per minute rates to you? how many minutes do you expect to use per month? We are in Tampa Florida and have 15 T1s from several different providers so I may be able to refer you to one if it's a match to what you're

Hi, Please forgive my terminology, still a bit new to T1s and such. I'm looking for a way to have 5 T1s from a carrier terminate into some type of box (multiplexer?), then be able to plug 7 asterisk servers into that box (each with single port T1 card) and be able to have 2 * servers go down at any given time and not actually have the carrier see that anything has happened. Obviously if a *

Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows. Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card. All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card. Any advice would be great. Zaptel.conf span=1,0,1,d4,ami e&m=1-23 dchan=24