similar to: TE405P

Hi to all, I have a problem with this wildcard and one E1 line. The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The kernel version is 2.4.26. I have donwload and build the latest CVS version of zaptel, libpri and asterisk following the ufficial instructions of digium. I have set up my server in this way: zaptel.conf loadzone=it defaultzone=it

I successfully installed asterisk@home 0.6, but when i try to load the wct4xxp module for the TE405P I just got, I get the following: Found TE410P at base address fb7ffc00, remapped to e0220c00 TE410P version c01a009b Tried to load 1c8ac800 into 00000000, but got 188ac800 instead Tried to load 1c8ac000 into 00000001, but got 188ac000 instead Tried to load 07fc07fc into 00000002, but got 03fc07fc

I heard that asterisk support r2 signaling. I'm try to test r2 using e100p. How should I configure zaptel.conf, zapata.conf? And if I want to modify source for customization, where should I start? Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040608/6392facd/attachment.htm

This afternoon I finally figured out more with regarding to a strange clock-slip problem we have on our asterisk box. We have two TE410s, in E1 mode: TE410P version c01a009b They have their own interrupts: 66: 781648298 783747388 IO-APIC-level t4xxp 233: 253890977 1311504670 IO-APIC-level t4xxp They have their full 31 channels: span=3,0,0,ccs,hdb3,crc4 bchan=63-77,79-93 dchan=78

Hi to all out there using HP DL380 G4 servers, i found a way to get the Digium TE410P with older firmware running on a HP-Compaq DL380 G4 Server! Here's the step-by-step description: 1. download the latest BIOS (in my case it was 4.04 from date: 06/02/2005) for the HP-Compaq DL380 G4 using the "Systems ROMPaq Firmware Upgrade Diskette for HP ProLiant DL480 G4 (P51) Servers" Link:

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

Forget the sound card. It isn't related. The subject above should have read 'TE405P No Voice Problem' or something similar. It appears to be a zaptel timing issue, but I have found a workaround. For those of you just tuning in, here is the story: I have a CentOS/Intel 865 box currently running Asterisk 1.2.7.1 and zap 1.2.5, both compiled from the source available off the main

Anyone care to elaborate on the differences between the T400P and the TE405P? -Darren -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050908/e817f8bb/attachment.htm

http://www.mixdown.ca/~asterisk/ The card seems to be working fine. Don't expect warranty on it though. :-) Why? Because I wanted a quad-span T1 card which worked in the high-end systems I was intending it for, but that I could also keep a few in stock and if the system mainboard failed, pull the card an put it in a standard PC system. I didn't want to have to stock 3.3V and 5V

Hi Everybody, Is there anyone who already uses Asterisk with TE405P card? Is this card going well with the old E400P or T400P drivers? Are there a lot of differences? In the card's data sheet writes this sentece: "Digium has designed the TE405P to be fully compatible with existing software applications..." Is this meaning the the old drivers are also OK for this card? Thank you

I understand from the archives that * does this occassionally, but I'm trying to figure out why. * didn't do this at all for two days, and then it's gone and done it 3 times in the past hour. It does not seem to be affecting calls, I'm just curious as to the reasoning behind the B channel resets and why they are so erratic. Regards, Andrew

I have TE405P span connected to a patton/digi 2977 T1/PRI port. Zaptel starts up fine without any errors. Libpri is installed as well. But I get the following when trying to load asterisk ------- Jul 3 19:30:26 ERROR[8192]: Signalling requested is PRI Signalling but line is in Unknown signalling 896 signalling Jul 3 19:30:26 ERROR[8192]: Unable to register channel '25-48' Jul

Hi, I havn't E1 board from Digium but I would like to know which is the used IC (chip) for PCI HDLC communication? Best Regards, Miroslav Nachev

Is there anything to choose, in performance, between a TE405P and a TE410P? I understand the difference between the PCI bus voltages, and certainly don't intend to try Andrew's hacksaw operation :-). But if I choose the card first, and a compatible mobo second, does it make any difference which? Cheers Tony -- Tony Mountifield Work: tony@softins.co.uk - http://www.softins.co.uk Play:

Does anyone know which physical interrupt line out of the four on the PCI backplane the TE405P uses? Or is it somehow configurable by hardware or software? I'm trying to diagnose a problem where the card generates no interrupts in one system, but is fine in another system. These systems are SBC-in-backplane type. My knowledge of how PCI works at the physical layer is rather limited, but I

Can anybody tell me the difference between a TE410P and a TE405P? Is it JUST the 5v vs 3.3v pcis slot spec, or is there some thing else? </edg>

Hi, I've got an * box with 4 E1 (TE405P) and a Class 4 Cirpack switch (www.cirpack.com). <IP Network>--<*>--<Cirpack>--<Public PSTN Network> ISDN interco is EuroIsdn, ports are configured ccs, hdb3, crc4. Cirpack is Network, * is Terminal/User. As I encountered some pb with Sip to Zap transcoding (* to Cirpack way poor quality, the other way fine), I tryed to

Can anyone with a TE405P tell me what zttool tells them the type of card installed. With ours it says it's a TE410P. B

Hi, I've got an * box with 4 E1 (TE405P) and a Class 4 Cirpack switch (www.cirpack.com). <IP Network>--<*>-[TE405P]-<Cirpack>-<Public PSTN Network> ISDN interco is EuroIsdn, ports are configured ccs, hdb3, crc4. Cirpack is Network, * is Terminal/User. As I encountered some pb with Sip to Zap transcoding (* to Cirpack way poor quality, the other way fine), I

Hello, I would like to know if FreeBSD has drivers for TE405P cards submitted to the ports. I have acquired a card and would really like to use it with FreeBSD. The wiki said the drivers havent been tested yet. Have there been any updates since then? regards Kavit _______________________________________________ Asterisk-Dev mailing list Asterisk-Dev@lists.digium.com