similar to: zaphfc TE -> NT problems

I've a lot af this waring May 12 18:44:35 WARNING[65541]: chan_zap.c:6070 zt_pri_error: PRI: received TEI check request for TEI = 76 May 12 18:44:36 WARNING[65541]: chan_zap.c:6070 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 May 12 18:44:42 WARNING[65541]: chan_zap.c:6070 zt_pri_error: PRI: received TEI check request for TEI = 76 How i can resolve it? Thak's Tiziano

Hi i've an hfc-s card with last bristuff installed at cli> i'm receiving: Sep 8 12:35:20 WARNING[1109552048]: chan_zap.c:6902 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 received TEI check request for TEI = 77 what is causing them? 10x Maurizio

I applied the florz patch but my problems remain. Now I get all sorts of weird errors on the console and I cannot make outgoing calls. Incoming calls work as expected. I am using a single HFC-S card with BRI. Any clue what these errors below are? Ri = 44651 TEI msg = 3 TEI = 7f Ri = 3800 TEI msg = 3 TEI = 7f Ri = 42399 TEI msg = 3 TEI = 7f Ri = 42409 TEI msg = 3 TEI = 7f Ri = 22078 TEI msg = 3

I'm running bristuff-0.3.0-PRE-1q The line seems to work but I get these messages on the screen every few minutes : 1 received TEI check request for TEI = 81 Jun 20 20:18:05 WARNING[27571]: chan_zap.c:8503 zt_pri_error: 1 TEI remove TEI = 127 Jun 20 20:18:05 WARNING[27571]: chan_zap.c:8503 zt_pri_error: 1 TEI remove TEI = 127 Any ideas ? Guess this is not normal behaviour? I'm using

bri-stuff.0.1.0-RC4a on debian sid with 2.6.7 kernel isdn sk: Bus 0, device 18, function 0: Network controller: Digi International Datafire Micro V (Europe) (rev 2). IRQ 17. Master Capable. Latency=16. Max Lat=16. I/O at 0xe400 [0xe407]. Non-prefetchable 32 bit memory at 0xd8021000 [0xd80210ff]. i still receive error messages continuosly (every few seconds) i

Hi, I have a partial working installation with zaphfc. Incoming call : For incoming call, seems work fine. But the sound is very bad with bounce short crashing sound. Same sound with echo cancel off or on. SDA work fine. Another problem, it's seems that's zaphfc don't reset correctly the line. I have one of my D channel how was busy even after stop communication. Outgoing call :

I've got a bit trouble with callerid and zaphfc cards. Basically zaphfc doesn't add the "0" in front of national numbers (haven't tried a international call yet). With chan_capi that allways worked fine, however i had to define the national and international prefixes in capi.conf. Is there something similar in zapata.conf ? Here is my zapata.conf: [channels]

Hi Folks, I've Asterisk Bristuffed up and running behind an Auerswald Commander Basic ISDN PBX on the internal ISDN Bus (BRI/PTMP). The HFC Card works marvelleous for outgoing calls (as the parallely installed avm fritzcard with chan_capi does), but when I'm trying to call in, I get a short ring signal and then the connection is terminated. This does not happen with chan_capi and

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 hi, i'm new to * I've installed an hfc-s card (DIGI Micro V) with bristuff 0.0.2; when i try to call outside i get: -- Accepting AUTHENTICATED call from 192.168.1.110, requested format = 1024, actual format = 1024 -- Executing Dial("IAX2[pippo@pippo]/2", "Zap/g1/0123456") in new stack Jul 13 13:42:49

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

I have the latest bristuff, a zaphfc card for external calls and a PRI card for connecting to a PBX as a channel bank. With a BRI I would expect to be able to have two incoming calls going at the same time, but when I try it, one call connects and the other gives the following console message, a busy tone, and then a hangup: Mar 23 19:18:35 WARNING[5595]: chan_zap.c:7512 zt_pri_error: PRI:

Please forgive me, if I misunderstand the problem completely. Following instructions in several german blogs, I want to configure Asterisk with a hfc-pci card, an old NTBA and an ISDN phone as a SIP device. It seems that I have to set signalling in zapata.conf to bri_net_ptmp. When I do this, Asterisk will hang if started with -vvvvc, the last lines of output being: [res_features.so] =>

Hi All Just got a new quadBRI card and connected one port to our Old PBX. When I make a call from a sip phone to a phone number the phone rings, I hook up, and the call on the sip phone allmost imidialely disconnects, after a fiew seconds the "real" phone disconnects too. Here is a trace: -- Executing SetCallerID("SIP/cramer1-b718", "45") in new stack --

Hi, I am running * with E100P board. At least every our I got an Error 500 message and ISDN-PRI restarts: Jan 10 12:53:02 WARNING[98311]: File chan_zap.c, Line 5758 (zt_pri_error): PRI: Read on 27 failed: Unknown error 500 Jan 10 12:54:27 WARNING[98311]: File chan_zap.c, Line 5758 (zt_pri_error): PRI: Read on 27 failed: Unknown error 500 Jan 10 13:33:01 WARNING[98311]: File chan_zap.c, Line

I have a "Cologne Chip Designs GmbH ISDN network controller" in my asterisk box, and an ISDN line connected up to it. I downloaded the bri-stuff 0.1.0-RC4a package from junghanns.net and used that to compile asterisk using these instructions: http://www.voip-info.org/tiki-index.php?page=Asterisk%20zaphfc%20install When I try to call my asterisk box, my sip phone rings twice and then the

Hello all, if I try to call from one phone on the internal S0 to another on the same S0 using zaphfc, the bus is hung up. The called phone is ringing, but I can't talk from one phone to the other. The error I get is: -- Executing Dial("Zap/2-1", "ZAP/1/55|15|tr") in new stack -- Requested transfer capability: 0x00 - SPEECH -- Called 1/55 -- Channel 0/1,

I'm not a PRI expert and therefore don't know what this debug stuff means for PRI, so if anyone can help me here... I'm running the latest libpri and zaptel from CVS. Keep in mind that everything works fine when using the STABLE libpri and zaptel. I am NOT running CVS asterisk. I am running 1.0.6. asterisk*CLI> pri intense debug span 1 Enabled EXTENSIVE debugging on span 1 T203

I have some problems starting asterisk with a hfc card using zaphfc: [chan_zap.so]Mar 8 17:53:06 WARNING[2447]: loader.c:258 ast_load_resource: /usr/lib/asterisk/modules/chan_zap.so: undefined symbol: ast_retrieve_call_to_death Mar 8 17:53:06 WARNING[2447]: loader.c:391 load_modules: Loading module chan_zap.so failed! I'm using asterisk from debian/sid: Asterisk

Hello, I am trying to use a HFC-PCI (CCD/Billion/Asuscom 2BD0) card in TE mode to dial-in and out with ISDN. The problem is I can not get the card to dial out with a Zap channel. Dial-in is working. I am using bri-stuff 0.1.0-RC4 (but tried also RC3 and RC2k). I tried all combination of "immediate", "overlapdial", "pridialplan". I earlier also managed to dial out