similar to: X100P don´t answer sometimes

I am trying to get distinctive ring to work on my PSTN with no luck. I can get 2 different ring codes but it skips the context assigned... here is my complete zapata.conf: [channels] signalling=fxs_ks usecallerid=yes rxgain=1.0 txgain=1.0 language=en context=default usedistinctiveringdetection=yes dring1=134,0,0 dring2=137,0,0 dring1context=internal2 dring2context=default

Is it possible to allow distinctive rings work for FXS ports as well? I need a certain FXS extension to ring a distinctive double ring. I modified zapata.conf appropriately for dring1,dring2 and it just Seems to ignore my updates. Do distinctive rings only work for FXO ports? Paul Seniuk -------------- next part -------------- A non-text attachment was scrubbed... Name: Paul Seniuk.vcf

Hello all! We have a PSTN line with four numbers calling into it. There is distinctive ring on these lines. They are are follows: 1. standard ring 2. short ring 3. long ring 4. short ring, long ring, short ring Based on the information I have been able to find, I have created the following entries in my zapata.conf file, to try and weed out some of the timings: dring1=95,0,0

I'm using Asterisk 1.4.5 (will try 1.4.6 on Thursday, but I don't see anything in the changelog after the 1.4.5 release dealing with distinctive ring), zaptel 1.4.3, and wanpipe 2.3.4-10 with a Sangoma A200 card. I enabled usedistinctiveringdetection in zapata.conf. However, on the Asterisk console, the output I get is: -- Detected ring pattern: 0,0,0 It would appear that Asterisk is

Hi gang. Just put an FXS port on a Zap interface for the first time. I can't figure out which parameters in zapata.conf are global and which ones can be channel specific & nested. I have mucked around with it but I can't seem to make any effect on the gain levels on a per channel basis. dring1context=pbx } dring1=0,0,0 } obviously global because it sets conditions for

Hi All, I was wondering what the status of distinctive ring support in Asterisk is? I had a google search & read and Mark Spencer wrote some support for it. Is distinctive ring different in every country or is it pretty standard? And for my final question, does the Wildcard FXO card support distinctive ring? Essentially what I'm trying to do is route incoming calls with ring #1 to,

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf

Hi, I have two accounts with broadvoice. Now, I want to be able to distinguish between them. I though that this would be simple by adding "/EXTEN" at the end of the register statement. For example: register => num1:pass@sip.broadvoice.com/1000 Unfortunately, this is not working. When I call into my box I hear busy tone. My config looks like this: [root@voip asterisk]# cat sip.conf

Hello! We are using the Digium 405PP card, and getting the following messages: Jun 16 16:16:17 NOTICE[81926]: chan_zap.c:6832 pri_dchannel: PRI got event: 6 on Primary D-channel of span 1 Jun 16 16:16:17 NOTICE[81926]: chan_zap.c:6832 pri_dchannel: PRI got event: 8 on Primary D-channel of span 1 My config file is below. We are trying to set up D-Channel on channel 24, 1-23 in trunk group 1,

I currently have Asterisk 1.2.7.1 and the Sangoma A200 w/ 6 FXO ports and HW Echo canceller. I have outgoing calling setup to use a group so that if one channel is busy it goes to one of the other channels. What's weird is that when I dial an outside number, sometimes it goes through and other times I get "You have reached an invalid pager number MCLL327." I have no idea what that

Todd How do you have the context in the phones sip configs set? Bryant From: "Todd Reese" treese65 at gmail.com Hi all, I've been have problems with getting this system on line and would like to acquire some help with the extensions.conf. My current problem is that the phones won't dialout.on the VOIP lines listed as dialout1, dialout2, dialout3. This version of asterisk

Hi All, I have just migrated from Asterisk 1.0.0 to Asterisk 1.0.5 and I have an X100P installed. The old asterisk was working, but now the new version isn't picking up any calls! However, I did notice that after installation, I performed modprobe zaptel and modprobe wcfxo and they worked fine, but when I executed ztcfg, I get the following errors: ioctl(ZT_LOADZONE) failed: Invalid

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

All, Alright, I've looked around the internet, the voip-info.org wiki, and browsed the contents of this mailing list. While I've found a couple of scenarios that are close to this one, I haven't found one that uses my particular card (T100P). Without further delay -- I have successfully configured internal SIP services between a Snom 200 and a Windows X-Lite client and have

I've followed the recent thread on caller id with UK British Telecom networks (where the caller id data is delivered before the first ring). My understanding is that if I use a recent CVS head (e.g. CVS-HEAD-09/18/04-17:45:52) and a TDM400 with FXO modules, all I need to do is include the line: usecallerid=uk In my zapata.conf (in the [channels] section) I've done this, but I get: Sep

Steve, Here is the config, I pulled from my server, that works with D'Link Phones: Main Menu -------------------------------------------------------------------------------- SIP.CONF [general] port = 5060 ; Port to bind to (SIP is 5060) ;bindaddr = 0.0.0.0 ; Address to bind to (all addresses on machine) bindaddr = 67.109.153.236 disallow=all ;allow=ilbc allow=gsm allow=ulaw

Today, We have added INVITE Authentication. This seems to bring a large amount of problems to people in the way since they can't make outbound calls. Here's what needs to be done. You need to add three variables to your peers or friends, username, authuser, and secret. username=<phonenumber> authuser=<phonenumber> secret=<registration password> Dan

Hello guys. I am a fairly new user to Asterisk, and I'm just having a tough time. My goal is to set up a VOIP PBX. I have signed up with a BroadVoice number, and I have three systems with SIP phones. The PBX and the SIP phones are all behind a Cisco PIX running NAT. I am using Asterisk CVS version from yesterday. I also tried 1.0.3 with little luck. The SIP phones are two X-Lites on

-------- Original Message -------- Subject: Re: [Asterisk-Users] BroadVoice configuration changes for Outbound Date: Sun, 06 Mar 2005 19:11:22 -0500 From: MF Hulber <mark@hulber.com> To: Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users@lists.digium.com>, dan@mirrorlynx.com References: <200503060703.XAA12457@comand.net>

I connect Asterisk to my analog PBX using X100P. In my analog PBX, I need to dial 0 (zero) to pick up the line. How can I use Dial command to dial (0 + telephone number) directly? I used exten => 10,1,Answer() exten => 10,2,Dial(Zap/1/0) exten => 10,3,Hangup It works, but I need to dial 10 and after the ring tone, the telephone number How can I do?