similar to: Question about x100P and zap

Ernest, I hadn't thought of doing that, though having that added protection would be nice. However, what I'm trying to do it have an incoming call at my home number follow me to my cell phone for selected numbers -- Since I already have three way calling, I'd like get Asterisk to essentially three way my cell phone into the call (or my office number, etc.) I understand the

Hi all, I have the Asterisk set up and 2 softphone (Xlite) set up on two other PC. With the following configuration, I can use one softphone (2000) to call the other one (2001) and/or the voicemail at 2999. Here is my problem: 1. When I dial 9+nxxx-xxxx with one of the softphone to the PSTN via X100P card, I got busy tone. (i.e. I want to use the phone line which is connected to the

Hi, can't get X100P (fully zapata compatible clone) to work (I'm in Australia). * recognises the card and the channel (1) but has definetely some problems talking to the pots line. I set up this simple dialplan for ZAP ("incoming" context, as setup in zapata.conf, for channel 1) [incoming] exten => s,1,Answer exten => s,2,Playback(somefile) exten =>

I'm trying to see if this is even possible. When you dial ext 2000 I want it to ring my sip phone for 20 sec then call my cell and let it ring for 10 sec if I do not pick up the call on my cell I would like it to go back to * and leave a voice message for me. Here is what I have so far in my extensions.conf Everything works except the call will not go back to * after the 10 sec rule has

Hi, I'm trying to set a rule to dial out through multiple Zap groups so that, say, g0 is the cheaper POTS lines group and must be used first. However, if g0 is busy or disconnected then try dialing out g1. My g0 group is made up of 4 analog lines connected to a 4-FXO card. I disconnected the RJ-11 wires from the FXO card to simulate a line disconnection. So theoretically all calls should

I am having dial out issues and was hoping someone could shed some light. The problem is Intermittent: extensions.conf [globals] ; Trunk Info for outbound calls via PSTN - See the zapata.conf file in /etc/asterisk TRUNK=ZAP/G1 ;Trunk Interface ;MSD digits to strip (usually 1 or 0), 1 = remove a leading 9 TRUNKMSD=1 ; -------------------------------------------------- ; [trunklocal] - Defines

I recently purchased a Asterisk Developer's Kit (TDM) and now have it outfitted with 2 FXO modules and 2 FXS modules. I'm not using the X100P modem card that came with the kit. I'm having problems with dialing out on my POTS line. Successful dial out is intermittent. About 50% of the time the call goes through. The other 50% it is dialing the wrong number. ( I can hear the error

Okay everyone - I'm moving away from using sipura 841 phones. I'm starting to test with Polycom IP 501 phones. We plan to upgrade our server to a dual t1 but, for now we have a digium tdm400P with 4 analog lines coming into it. So my question is will upgrading the IP phones with my existing digium tdm400 card be enough to satisfy my users ? or is it really a combo deal needing to

Hello all, I want to setup Asterisk to forward a call if the dialed extension is busy. I do not want to wait on the line until the extension timeout expired. What I want is when I dial am extension currently Busy (Talking with someone), asterisk inmediately forwards my call to an extension I previosly defined. Someone could help me? Any clue will be appreciated. Regards from Spain. Ismael

Hi everyone: I've searching for a while and haven't found what i need. The thing is that i have a tdm422p with the two fxo ports connected to the pstn. I want my sip users to be able to call other numbers(any number) in the pstn through my zap fxo channels. I have a big number of sip users so as you can imagine there will be congestion when some of them(more than two!!) want to call

When I place a call using Iconnecthere as my sip provider, I hear no ringback when making a call. Does anyone else have this problem or offer any suggestions? Thanks, Kevin -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031003/b048f72f/attachment.htm

Hello All, I have some Polycom IP 500 phones that I would like to have configured for direct dialing to our voice mail system. So far I have been unable to get the hard button labeled Voice Mail to connect to Asterisk without first passing through the message center prompts. I have followed all the Admin Guide instructions regarding the phones .cfg files and using

I've just installed an X100P, built the kernel module, and tried to use it to make an outgoing call (via a phone connected to an ATA-186). However, I just get a reorder tone and see this on the console: -- Executing Dial("SIP/ata1-4409", "Zap/1/5551212") in new stack NOTICE[1200825920]: File app_dial.c, Line 481 (dial_exec): Unable to create channel of type

Hi, I'm trying to get my X100P to Dial the following sequence to gain access to speed dial numbers on my Norstar PBX that the X100 is connected to... [FLASH] [*] [0] [22] (where 22 is the speed dial number) But so far I've had no luck, with the following extension:- exten => 922,1,Flash(${DIALOUTANALOG}) exten => 922,2,Dial(${DIALOUTANALOG}/*022) exten => 922,3,Congestion

Hello, everyone. Right now, we are trying launch our own PBX system based on Asterisk(Fedora) with Cisco 2611. Cisco has 2 port FXO card installed on it. For testing, I have 2611 hooked into phone line with number of xxx-xxx-xxxx fine. (I'll call it F). Using softphone, I can dial in extension 1001 on asterisk, which should talk to cisco. After initial connection to Asterisk, I have try to

Hi All, I am using a Grandstream BT100 and I have been trying to get the PBX features to work for DND, call foward, etc. These functions do work when I use my POTS phones hooked up to my Zap cards. But I cannot get the PBX functions (ie *78, *79) to work using my SIP phones. Is there a feature that has to be enabled to do this? I know these functions are available within the GS phone but all of

Guys I am having some serious issues with my call queue and Management is breathing down my neck pretty bad, and I am running out of ideas. I have a single queue for my tech support department. I originally was using the AgentCallbackLogin for them and it tested out great on our testing weekends, but it hasn't worked out since. It would only let one of them take calls at a time, no matter

Ok. I am confused. I now have conflicting answers to my question: Do you need to use a special phone to use SIP? My setup is X100P and TDM10B. I would like to connect to iConnectHere, which uses SIP. Has anybody done this before (using similar equipment to what I have listed above)? And if it is not possible, could somebody please explain why. I don't understand why this wouldn't

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Can the Dial() command tell the difference between busy and congestion? At the moment it seems to be treating them both the same on my server. I want to route the calls out via a SIP gateway unless that is congested, in which case dial out through my POTS line (using an X100P). It seems a bit pointless to try dialling the POTS line when the SIP

Hello, This is my first asterisk installation, and having read up on the documentation, and trying several tutorials i'm unable to get my outbound route working. I'm certain it's an issue with my configuration and my inexperience with asterisk. So i have my POTS phone connected to my digium card, and when i make a call, I receive the "cannot be completed as dialed" message.