similar to: H323 -> IAX

Hello r helpers! Below is the whole coding for my programme. Before proceed more further, let me explain for you. First of all, I need to compute trimmed mean. Till that step is ok. Then I need to compute ssdw which is sum of square deviation. If I do equal trimming at both tail of distribution that I chose, I will use the first ssd formulae which is "a". But if I am doing unequal

Hi there. I am trying to connect Asterisk to a local danish ip-telephony provider. But is having some difficulties. First I thougt they were related to the provider. But then i started debugging on the Asterisk (aix2 debug) When I make a call using AIX to the provider everything seems to work just fine: *CLI> -- Accepting AUTHENTICATED call from 192.168.1.150, requested format = 1024,

I'm trying to link up Cisco MGCP-enabled router (residential gateway) with Asterisk, and it looks like some sort of protocol mismatch, could it be MGCP 0.1 vs 1.0? Look at this (x.x.x.99 is the router, x.x.x.98 is Asterisk): MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427Verb:

Hello list, hope someone can help me - I'm going crazy using the FXO port a SPA3012. I would like the SPA 3012 to act as a simple FXO port to an Asterisk, that is, once it detects a call, it should simply send it over to the local Asterisk server. No intelligent routing, PIN, anything else.... I configured it like this: PSTN-To-VoIP Gateway Setup PSTN-To-VoIP Gateway Enable: yes PSTN

Hi Who concern, I setup TINC VPN follow these. 192.168.1.x / 24 (Client groups) | 192.168.1.1 (eth1) (GW1) 202.44.34.206 (eth0) || Internet || 202.44.45.14 (eth0) (GW2) 192.168.2.1 (eth1)

Hi, I've searched the archive but can't seem to find the answer to my problem. i have two gateways running with asterisk , my question is : is there any possibility to do failover with gateways with asterisk ? i mean that if one gateway is down , asterisk switch automatically to other gateway . i have succefully used failover with limit number off calls (if gw1 have max calls ,asterisk

Hi there. I thy to compile asterisk-oh323-0.6.3a but it fail in the make command. I have the pwlib-v1_6_6-1 and openh323-v1_13_5-1 as saying in the README file of the packet asterisk-oh323-0.6.3a I do make and this is the error: # make for x in wrapper asterisk-driver; do make -C $x all || exit 1 ; done make: *** No rule to make target `ccflags'. Stop. make: *** No rule to make target

Hi, I having a problem compiling the wrapper for oh323. I am running Debian, kernel version 2.4.18-bf2.4. The pwlib version I have is 1.6.6 and the openh323 version I have is 1.13.5. I execute the following commands first before attempting to compile the wrapper: pwlib_1.6.6: make both openh323 1.13.5 ./configure make opt asterisk-oh323 0.6.2 make

I am blocked on the most simple step when compiling Oh323: Cd /openh323 patch -p1 ../asterisk-oh323-0.7.2-pre1/openh323_1.13.5-make.patch it hangs for ever and never finishes in my machine with Red Hat Enterprise Linux 3, fully updated. I need to use Asterisk HEAD and I therefore I want to use asterisk-oh323-0.7.2-pre1. Additionally, because it is the most debugged version. In the past, if

I have setup my Asterisk 13.1.0 server with PJSIP on AWS/EC2. My basic configuration works, and I am connected to a SIP trunk using SIP.US, and have set up my inbound calling which works correctly (when I call my PBX DID, the call does come into my PBX network). The issue is that I am not able to make outbound calls, because the call fails with the error:

This post is simply documenting a spouse-friendly way of using the spa-3000 as both a fxs and fxo port for basic soho environments in the US, allowing asterisk to participate as needed/wanted. All home phones are connected _only_ to the spa-3000 fxs port. The incoming home pstn line is connected _only_ to the spa-3000 fxo port. Defined Line 1 (fxs) to register with asterisk via sip (extn

Joao, Thanks for sending the Installation tips as pasted below. It works. Seshu ---------- Get oh323 from http://www.inaccessnetworks.com/projects/asterisk-oh323/Libraries/openh323-Janus_patch4-src-tar.gz Get pwlib from http://www.inaccessnetworks.com/projects/asterisk-oh323/Libraries/pwlib-Janus_patch4-src-tar.gz Get asterisk-oh323 from

Hi, I am using asterisk CVS 2004-06-16 with oh323-0.6.3a I have a strange problem if I start asterisk with oh323 loaded /usr/sbin/asterisk -vvvvvc once I am in the console and issue "restart now" or "reload" asterisk hangs and it not stoping or restarting at all, below is the console logging when it happens, as you can see it stucks on "Destroying any remaining

That was the issue, thanks. I now am able to get the caller ringing on an outbound call, but an external phone number (E164) I am dialing does not ring. On Sun, Mar 15, 2015 at 12:19 PM, George Joseph <george.joseph at fairview5.com > wrote: > > > On Sun, Mar 15, 2015 at 8:32 AM, Sonny Rajagopalan < > sonny.rajagopalan at gmail.com> wrote: > >> I have setup my

Why is no one suggesting any solution here for this problem, which has been lingering for a while. Are we not supporting H.323 on Asterisk? -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com]On Behalf Of ruixun wu Sent: Thursday, July 22, 2004 4:06 PM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] still can't

Hello, I have a strange situation with an SPA3102 FXO/FXS device. I'm in situation that when i receive a call from PBX line I must forward the calls to 2 VoIP numbers. Right now i have the following settings: (S0<:1010 at GW1>). I want to forward at 1020 too. I tested (S0<:1010|1020 at GW1>) and doesn't work. Did you have any other ideea? Thank you.

Ok I upgraded tonight a server from CVS in Late NOV to one just downloaded tonight. It all runs up OK and I can contact it from my ATA 186 using g729a codec and that all works fine. What I am having trouble with is connecting through IAX ATP.org.au in AUS to my server. The connection comes through OK I can see all the tracking info in the console OK but I get 0 audio in either direction.

I have the following in extentions.conf: exten => 2111,1,Dial(SIP/2111 at gw1.langley) exten => 2111,2,Voicemail(u2111) exten => 2111,3,Hangup exten => 2111,100,Voicemail(b2111) exten => 2111,101,Hangup I have the following in sip.conf: ; Cisco 1750 [gw1.langley] type=friend host=172.16.17.1 context=default canreinvite=no Like the ATA, lots of stuff doesn't work on the 1750

<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> <meta content="text/html;charset=ISO-8859-1" http-equiv="Content-Type"> <title></title> </head> <body bgcolor="#ffffff" text="#000000"> <font size="-1">Hi List<br> <br> </font> <pre

Dear All, I have problem with new oh323 0.6.3a , I try use var OH323_OUTCODEC, but it don't work. oh323 driver don't want connect to gateway with g729, it's work if I only use in oh323.conf one codec ( g729 ). If I enable 2 or more codecs - always in use other codec: -- Executing SetVar("IAX2[4010@4010]/1", "OH323_OUTCODEC=g729a") in new stack -- Executing