similar to: Outgoing CLI

Calling out on PSTN over a TDM400P seems to generate a Red Alarm - whatever that is. I have another extension on the PSTN, and I can dial out over that. zttool shows no alarms. asterisk*CLI> zap show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TDM400P REV I Board 1 OK 0 0 0 CAS Unk YEL 0 db

Dear All, I am trying to setup an ISDN line from local telco on a digium card. The problem I am facing is that I am not getting any caller id from the telco. They say that they have enabled caller id. Please help me out. My zapata.conf -------------------------------------------------------------------------------------------------------------------- [trunkgroups] [channels]

hi! I need to pass the CLI for my outgoing ISDN PRI call from * box. here's the ISDN protocol debug. Q.931 > Calling Number (len=10) [ Ext: 0 TON: Unknown Number Type (0) NPI: Unknown Number Plan (0) > Presentation: Presentation permitted, user number passed network screening (1) '123123' ] > Called Number (len=12) [ Ext: 1 TON: Unknown Number

Hello, I am missing any description of zaptel/DAHDI alarms. The TE200 series user manual contains only a description of LEDs states. These alarms states are visible in zttool/dahditool or in astersick CLI (zap show status) and I wonder what is the real meaning of these alarms for E1 channel. Possible alarm states (based on zaptel.h 1.2): 1. No alarms 2. Recovering from alarm 3. In loopback

Nik, I'm not sure that "NOP" is correct, but I'm in the states so I'll to defer to someone who knows E1/PRI. When I run zttool I have "OK" under the alarms. Is there a way you can call the telco and confirm the settings? Make sure that framing, coding and D channels are set up on their end the same way you're set up. As for asterisk, here's what I get

Hi, When we make an outgoing call on ISDN (zaphfc) with overlap dialing we get immidiate hangup after answer. But when we place a full number before dialing everything is ok. Any help appriciated!! Thanks here is info with debug: == Primary D-Channel on span 1 up -- Executing Dial("SIP/200-164c", "zap/g1/|100|tc") in new stack -- Making new call for cr 192 --

Hi everyone. We have a problem here... Hope somebody can give us some hints. We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)

Hi All, I would appreciate a lot if you could help me. I have installed Asterisk 1.4.1 and zaptel 1.4.2 on my redhat enterprise linux 4. I have also installed 1 FXO port card: Digium TDM400P. After loading zaptel driver I could see my digium card's led glow green. Tested with zttool that its in OK state. I have configured fxsks=4 in zaptel.conf(channel 4 cause FXO module is on port 4). I

Dear All, I have an asterisk server version 1.2.12.1 along with trixbox and I am having this nasty problem, I have a TE200P and have an E1 pri attached to it and zttool says it's OK, I have configured the whole 31 channels into one group as follow: Zapata-auto.conf: callerid=asreceived signalling=pri_cpe switchtype=euroisdn context=from-zaptel group=0 channel=>1-15,17-31

currently we are able to use our USA sip phone to conenct into the E1 box, but still unable to dial out to chinese phone numbers. They said from their ISDN switch console, it shows D channel not connected to the voip server yet. here si the sip debug msg, we got a Message type: DISCONNECT (69) and unable to dial any numbers. Jul 12 12:56:26 WARNING[1523]: chan_zap.c:1931 pri_find_dchan: No

I use a E100P in France with a french operator E1. I can receive calls via the E1 and tranfer them to a VoIP phone, play IVR etc .... But outgoing calls doesn't work at all. I receive a RELEASE COMPLETE just after the SETUP. There is no pb with the operator (the E1 work well with an other Pbx). Here a call trace. Anyone have an idea ? (g1 is my group name for the 30 channels) -- Accepting

Hello, Quick Diagram: Telco-PRI -> Asterisk <- Norstar PRI -> Norstar PBX (DMS100) (TE405P) (DMS100) | | V Cisco 7960G (SIP) I'm trying to change the Origination Number on my outgoing PRI, and running into a weird problem. If I make a call from a SIP extension off asterisk using the following context:

We have an old Telrad 128KSU PBX to which I am trying to connect asterisk in the following manner: Current Setup: Telco-> T1->PBX Desired Setup: Telco-> T1-> Asterisk-> T1-> PBX. I am first trying to setup the Asterisk -> T1->PBX part without disturbing existing setup so I can get asterisk to forward calls to PBX and once that is done, I would try to move the telco

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

I have a T1 link from asterisk 1.2.23 (also tried with 1.4.13) to a Meridian Option 61C. Calls either way drop with error "Channel 0/23, span 1 got hangup, cause 100". Can anyone offer insight into the cause and solution/workaround? (I tried upgrading to Ast 1.4.13, and upgrading matching zaptel & libpri, put the problem is identical). For testing, I tried a call from the

I have a server running Asterisk 1.4.14, Zaptel 1.4.6, Libpri-1.4.2 on a CentOS 5 server. The server has a single TE110 card connected to a provider called Alestra in Monterrey, Mexico. Since we installed everything we have been having problems dialing certain numbers, those numbers always fail when dialed from Asterisk but if you dial from your cell phone they always go through. I once has a

Hey all, I had a user complaining of calls which were dropping mid-conversation. I looked into the time of one of the calls, and saw the following: Apr 4 12:13:03 WARNING[6670] chan_zap.c: No D-channels available! Using Primary channel 28 as D-channel anyway! Apr 4 12:13:05 WARNING[6660] channel.c: Avoided initial deadlock for '0x82b8430', 10 retries! Apr 4 12:13:05 WARNING[6660]

Has anyone had any compatibility issues with a TE110P card installed on a Dell Poweredge 1950? I noted the following error on the LCD display of the Dell Poweredge 1950: E1711 PCI PErr Slot 1 E171F PCIE Fatal Error B0 D4 F0. The Dell hardware owners manual states that it means the system BIOS has reported a PCI parity error on a component that resides in PCI configuration space at bus 0,

Hi, If I do this in extensions.conf exten => 411,1,Dial(IAX2/hhandresen@iaxtel/18005558355@iaxtel,40,rS(10)) the line is cut of in 10 sec., thats fine, but in CDR I got dst as T, and not 411. How can I handle this so I still get kicked of after 10 sec., but get 411 as dst in my cdr ? -- mvh. Hans-Henrik Andresen

Hi, Have a problem in my extension.conf: I have: [sip] exten => _333.,1,wait,3 exten => _333.,2,Answer exten => _333.,3,AbsoluteTimeout,7 exten => _333.,4,Hangup I wanted to test if * is executing this dial plan by calling 3335254255 for example. The problem is as follow: It waits, it answers but it does not seems to see the Absolutetimeout: call goes forever. What's wrong? Am