similar to: Codecs and pauses

Hi everyone I'm interested in using the Telappliant/voip-talk offering as an alternative to my DDI analog problem. (see [Asterisk-Users] Multiple DDI & Hunting on Analog Lines (UK) for details) Does anyone on the list have any recent comments on reliability etc? I would really appricated some positive and negative comments. Cheers Matt

Does anyone know of a BYOD provider that terminates calls to NCFA numbers (UK 'national rate'). I enjoyed broadvoices unlimited to those numbers, but this is getting silly now, it doesnt work and no answer if after switching to a new provider it will ever work. Can anyone suggest an alternative provider that serves NCFA? -- Trixter http://www.0xdecafbad.com UK +44 870 340 4605

Hi, I have installed the latest version of asterisk(1.4.0-beta3), and built app_rxfax/txfax. I'm using spandsp from here, http://www.soft-switch.org/downloads/snapshots/spandsp/spandsp-20061207.tar.gz Everything builds ok. I had to manually apply the patch from the site so configure would spot spandsp libraries. However, when I try dialing my virtual fax extension (either from a phone or

Hello folks, i upgraded to the actual CVS head from yesterday (27.5.) but can not get incoming SIP calls from my provider (sipgate). If someone calls my number, my asterisk responds with the following error: May 27 21:30:21 NOTICE[1114606512]: chan_sip.c:6351 handle_request: Failed to authenticate user "<CallerID>" <sip:<CallerID>@217.10.66.11>;tag=as38e9693c I

Hi, Anyone used this service, any comments on reliability/support? Thanks John

Any recommendations for a VoIP provider in the UK? I have a few guys in a field office in the UK with SIP phones and a VPN tunnel back to a working Asterisk setup in the US. The Asterisk setup has an IAX trunk with TelaSIP/VoipXpress with local DiD's for US offices, so they can call vendors, customers etc in the US at local rates. I'd like to get the same thing for the UK, so that UK

Hi, Despite much searching, I can't find anything quite like the problem we seem to be experiencing with our recently activated asterisk pbx. Of four people answering several calls per five minutes, I have reports of the occasional call starting with dead air. The user picks up the call from the queue, and they can hear that the line is too quiet. If they start talking, the caller either

I went on a service call yesterday to find an asterisk system with a T100P card on a Qwest PRI and a TDM40B card connected to fax machines. The TDM40B LEDs were not lit, and the system did not respond to keyboard input. However, calls were being processed for the PRI and 7960 phones. I replaced the TDM40B card with a new one, and the system now seems to be ok. But I'm wondering, why

Hello Everybody, I was going thru the C code of Asterisk. Does anybody know how does one go about modifying the C code of Asterisk? Please do reply. Regards, Bharat M. Sarvan EZZI BPO Pvt Ltd., PUNE. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: Steve Beaumont.vcf Type: application/octet-stream Size: 215 bytes Desc: not available Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20041226/1c213f8a/SteveBeaumont.obj

Ive just installed a TDM4000P with 4 fxos. The zaptel config is fine, zttest comes back with configured. If i call a line when zttest it shows on the display,and then goes when the line drops. In * when a call comes in, it follows my dialplan and answers the call according to the log, but IT DOESN'T actually pick up the call, i.e. it continues ringing. I'm using KS signalling, and

Hi all, Does anyone know of any providers that can offer local numbers based in the UK via IAX or SIP? We're looking at getting a number based in the UK. Thanks! -- jeremy bogan [ jeremy@segpub.com.au ] segment publishing - design.develop.host

Hi, I am looking for voip termination all over the world especially based on IAX or SIP. Regards. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040124/25e16736/attachment.htm

Have anyone tried to interface BT's Broadband Voice with asterisk? Kannaiyan

I am new to Asterisk so can I start by apologising if this question has been asked and answered already. I'm in the UK using BT for two incoming lines, one on Wildcard TDM400P and the other on Wildcard X100P. I also have a SIP connection to voiptalk.org. Incoming calls via SIP/broadband ring on extensions immediately. However, an incoming call via PSTN is displayed on the CLI as an

Hi, Currently using voiptalk.org and the quality is getting really bad. I would like a second provider preferably in UK, anyone got any suggestions? Ta. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040421/3d91c7f6/attachment.htm

Hi, methinks that in the good 3 months since i ordered an IAXy, things have changed so much that now almost anybody out there with a VoIP hardweare website offers complete phones for less money than the IAXy, with support for both IAX2 and SIP in many cases, and fully configurable via its own keypad. What would you recommend as a rugged, small, and easy to configure/use self-contained unit that

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I've got my developers kit from telappliant and got a machine up and running to become the house phone system. Most things are working now, such as incoming calls, call transfer, call parking, voicemail, etc. The one thing I can't do is make my analog phone ring! I can see the call coming in on the asterisk console and can then pick

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Does anyone have any recommendations on an IAX Desktop Telephone or ATA Device. I currently have 2 of the SIPURA-841's on my local network and now I am wanting to try an IAX Device at my remote office since I think that it would be easier to configure through various routers than a SIP Device. I just started to look at the Digium IAXy Single FXS

Hello folks, I'm having trouble configuring Asterisk to play an "invalid extension" message to anyone dialing an undefined extension. First I tried using the 'i' pseudo-extension, but it didn't work at all; searching the wiki I found that page: http://www.voip-info.org/tiki-index.php?page=Asterisk%20i%20extension where it basically says that the 'i'