Displaying 20 results from an estimated 400 matches similar to: "Problems with Zaptel"
2005 Oct 12
1
Problem with PRI and Ericsson AXE 10
Hi everyone,
I have a PRI conection on an * system running Asterisk 1.0.9, libpri 1.0.9 and zaptel 1.0.9.2 connected to an AXE 10 (APZ 21220 System 64) in the network side. I know the system and the wildcard I´m using are ok because I´ve used them before with other PRI connections (to a Siemens EWSD) without any problem.
First the PRI didn´t work (I got the TE110P alarmed with red). After
2005 Aug 02
2
Channel Bank Help Please....
Hello -
I have a Premisys Slimline Channel Bank connected to a Digium TE110P. I
am not able to call the FXS extensions or get dialtone on them. The
channel bank is connected via a T1 crossover to the cable and lights
show green. I really need to get this functioning by end of day. If
anyone can help me out I would be greatly appreciative.
Thanks,
Dave
zaptel.conf
loadzone =
2009 Mar 31
1
PRI problem
Hi guys,
I've been trying to get my ISDN-10 line up for the past few days, but
its been going up and down. I am using OpenVox D110P card on
asterisk version 1.4.21. It seems to me like a cable problem. I tried
using Ethernet straight cable (12, 45, 36, 78) and also a "straight"
cable where the twisted pairs are on 12, 34, 56 and 78. The problem
remains the same.
2005 Mar 10
7
Panasonic TDA200 E1 -> E100P negotiation issues
Hi, I hope someone can help me with this....
Asterisk 1.0.6 Zaptel 1.0.6 Libpri 1.0.6, 1 Digium E100P card installed
Panasonic TDA200 firmware v2.0.6 E1 Card Firmware 1.0.2
System is located in Australia, so as technologies go, I believe it is twist on the euro standard for the E1 signalling.
Here is the situation.
The TDA E1 card is set in cross over mode and I am using a functional
2006 Mar 01
3
my zap channel not ringing
I need your help
I have a sangoma A104D on my dell server; I got card status ok with no alarm
If I dialed the extension 6210006, it shows the output as stated below, but
there is no ringing from the pstn number nor the iax softphone am using on
my pc.
I will be glad if someone can give me a working config?
What I want to achieve is to send all my call to the pstn on A104D?
The pstn am
2006 Dec 28
1
TE110P with Qsig
Hi all, as good?
I am trying to go up a board TE110P with link E1 ISDN PRI to establish
connection with a central office Siemens HiPath 4000. But I am having the
following errors:
Server1:~ # asterisk -r
Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others.
Created by Mark Spencer <markster@digium.com>
Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'
2007 Nov 20
1
Problems with losing D-Channel on
Hello all,
I got a problem at an asterisk server, with dropping calls, losing all
channels and reaktivating all channels and beeing back up.
This problem seems to occure randomly over the whole day, when it gots
traffic on the card.
After looking @ google I found several hints but none did work fine.
To avoid problems with the phone line (german E1) I called the provider, he
did a 45 min. route
2004 May 31
5
D-Channel Problems
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Good day eveyone,
I'm hoping that someone can help me. Perhapps i'm overlooking the obvious,
in truth, I hope that I am. I've scoured the mailing list and google,
and haven't come up with much.
I have a Digium T400P thats been connected to a channel bank for testing
for some time now. all has been well.
I've now just had
2006 Oct 19
3
Bristuff qozap drivers problem
Hi,
For a significant time now (since about 0.2.0-rc8n) the qozap driver
has become very verbose if an ISDN line is not connected... I get the
messages below every couple of seconds in the asterisk logs.
The "flaw" in the messages is the "Alarm cleared" message - The alarm
cannot possibly be cleared because there is no physical media
connected into that port!!! (BTW - All
2003 Mar 13
1
E1 yellow alarms
About every hour I see the yellow alarms on all or a number of channels of
my PRI which is connected to the dutch telephony network, Asterisk keeps
on working fine....
Here's an example where channel 1-24 went into alarm:
WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event): Detected
alarm on channel 1: Yellow Alarm
WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event):
2004 Mar 30
9
Zaptel/PRI problem
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hi.
I'm getting the following error at random intervals on my TE410P with Asterisk
CVS-03/30/04-11:49:01-CEST.
I have two spans active, one connected to my Telco, the other to a Siemens
PABX. Both spans display this behavior at random intervals.
All calls are dropped when this happens. Spans are not necessarily in use when
this happens.
2003 Dec 10
1
Errors after re-plugging T1
Hi,
After temporarily pulling the T1 cable out of our Asterisk box, we ended
up getting a strange error messages even after the cable was plugged
back in.
[...]
Dec 10 09:01:11 WARNING[1192437440]: File chan_zap.c, Line 5683
(zt_pri_error): PRI: Read on 63 failed: Unknown error 500
Dec 10 09:01:21 WARNING[1192437440]: File chan_zap.c, Line 5683
(zt_pri_error): PRI: Read on 63 failed: Unknown
2001 Aug 06
3
Who'll Be Using Ogg Vorbis Instead Of MP3? @ /.
Check out the discussion.
http://slashdot.org/askslashdot/01/08/06/0415253.shtml
A lot of what is on there I have seen come across this
list. The general feeling is that ogg won't overcome mp3.
__________________________________________________
Do You Yahoo!?
Make international calls for as low as $.04/minute with Yahoo! Messenger
http://phonecard.yahoo.com/
--- >8 ----
List archives:
2009 Mar 26
2
PRI dropping #2
Hey,
I wrote yesterday about PRI dropping, which turned out to just be a
regular reset of unused B-channels. This time there's a real issue. As
noted earlier I have an ISDN-30 connection, a Digium TE-121 with
VPMADT032 echo cancellation. These are my configurations files:
== /etc/zaptel.conf
loadzone=dk
defaultzone=dk
span=1,1,0,css,hdb3,crc4
bchan=1-15
dchan=16
bchan=17-31
==
==
2003 Mar 01
3
ices 'script' playlist information?
Hey all.
I've got my streams running, they're working quite awesome so far.
But I've got a question about automation, and the ices2 "script" playlist
option.
Is there anywhere I can go to get detailed information on how this works?
I'm wondering about passing information back and forth, for example, or
if there's anyway to collect information like the audio program
2005 Dec 22
1
Ask Slashdot: Is Ruby on Rails Maintainable?
Ask Slashdot: Is Ruby on Rails Maintainable?
Posted by Cliff on Wednesday December 21, @12:51PM
from the would-you-want-to-edit-the-code-later dept.
kale77in asks: "I''ve become a big fan of Ruby over the past few months, but I''m not at all sure about Ruby On Rails. Automatic code generation sets of alarm bells in my mind; so that, to RoR''s promise of
2005 Feb 23
5
Zaptel Red Alarm
Guys.. I just saw this for the first time... I did some google and wiki
without any luck.. what does a red or yellow alarm mean in zaptel?
Feb 23 02:54:16 WARNING[16890]: chan_zap.c:5865 handle_init_event: Detected
alarm on channel 2: Red Alarm
Feb 23 02:54:24 NOTICE[16890]: chan_zap.c:5860 handle_init_event: Alarm
cleared on channel 2
This just happened by itself..
2011 Jan 11
1
Issue with Red Alarm with DAhDi
Hi!
I have an analog line connected to my asterisk and when I try to answer a call I get this
-- Starting simple switch on 'DAHDI/7-1' -- Executing [s at from-pstn:1] Answer("DAHDI/7-1", "") in new stack -- Executing [s at from-pstn:2] Playback("DAHDI/7-1", "vm-intro") in new stack -- <DAHDI/7-1> Playing 'vm-intro' (language
2003 Jul 24
1
FWD no longer works.. but nothing has changed? Wierd DEBUG errors.
I'm wondering if anyone else has gotten something similer to this? I
had FWD working fine on the asterisk box, then all of a sudden it just
stopped working. I get the following errors (just keeps looping)
*CLI> DEBUG[1125329600]: File chan_sip.c, Line 527 (__sip_ack): Stopping
retransmission on '6dc8436c7c568eea75fffdc75478ed54@142.55.31.179' of
Request 102: Found
2003 Sep 11
1
Segmentation fault due to SIP registration N UMBER 2
Hello,
Don't know if this is related but I just got a segmentation fault today
while trying to register my new SNOM200 phone:
*CLI>
*CLI> NOTICE[1125329600]: File chan_sip.c, Line 4713 (handle_request):
Registration from '<sip:mattf2@10.10.10.15>' failed for '10.10.10.14'
NOTICE[1125329600]: File chan_sip.c, Line 4713 (handle_request):
Registration from