similar to: Connect 16 E1/T1 between * and other switch...

Robert, > Is there a product to simulate a PRI trunk? (Robert > Goodyear) TDMoE emulates a T1. ;) Once the TDMoE link is up, Asterisk just sees 24-lines that appear to be a T1 instead of having to deal with all of the complexities of VoIP. This is useful, since probably 75% of the utility of VoIP is really just the fact that it can run over a network. It's also handy because it

This has been an interesting discussion for me (except for the sniping). The last post led me, out of curiosity, to this wiki entry: http://www.voip-info.org/wiki-Asterisk+TDMoE I was unaware of this feature, and it looks pretty good. I've been pondering replacing some T1's by leveraging IP capacity but of course have run up against the QoS issue. My idea was different... I

Has anyone every attempted to set up a mini PC to achieve much the same functionality as the fonebridge box? The sort of thing I'm imagining is a micro itx board & case in a completely solid state configuration (flash disk, maybe a psu fan but only if really required), with a TE210P (or equiv) card(s). The sole purpose of this would be to be a bridge between E1 lines and TDMoE. The

When I was trying to run mutiple E1s over TDMoE, the zaptel would drivers complain about too little memory, whenever I added more than 31 channels. Requesting 62 channels in a dynamic span gave me ... span creation failed: Cannot allocate memory upon loading the zaptel drivers. How would you go about running, 8 or 16 say, E1s over TDMoE? Would you create multiple dynamic spans or just one large

Hello All, I have a request from a prospectieve client to deploy a PBX capacity that can do up to 3000+ lines within a geographic region similar to a campus. The client wants analog lines for extensions and maybe VoIP for some backhaul traffic while the other traffic would be carrid via E1 channels. The client has other proposals to buy a mid, range telco switch from alcatel or simens but i am

Can anyone point me to a reference or sample config for bypassing a nailed up (point to point) t1 between two PBXs with asterisk and a pair of t1 cards? Right now I have 2 Nortel norstars connected to each other via a leased line t1. I also have a solid 10mbps low latency microwave link between the 2 sites. My goal is to run an asterisk box at each end with a t1 card and Ethernet card to

Is it possible to support 32 or 64 E1 in a linux box with Wildcard E400P board ? I'd like to make large scale PPS system. Thanks in advance. See Young Oh. DIGITALWAVE,INC. -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20030304/c1f8d74f/attachment.html>

I'm having (I think) timing issues in relation to bridged T1-T1 calls via dynamic spans. Fax calls are intermittently working, but voice is fine. My box has a Sangoma A400 inside it as the primary Zaptel timing source. My T1 PRIs that are hooked to the box come in via a foneBRIDGE2 (dynamic TDMoE spans). PRI #1 is the telco and PRI #2 is an existing Comdial FX-II. For some reason, bridged TDM

In all the information on Asterisk it takes about TDMoE to link asterisk servers together. Is this IAX??? How would I use TDMoE. Maybe my first question should be, What is it??? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030516/cd74bddb/attachment.htm

Dear, I have two Asterisk PBXs with an E1 interface/RJ-45 port in both boxes. I need to connect both PBXs with E1/R2 and UTP cable. What are the requirements to deploy the UTP cable ??? Straight-through or crossover ??? What are the pinouts in both peers ??? Thanks a lot, Alejandro

Hello, I want to link several * boxes together. Some of them are dedicated as "user" servers (SIP and IAX clients connect to them) and some are used as PRI servers (where the PRIs are hooked onto). I think TDMoE is the only channel type where you can group different Interfaces into a single group. E.g. for using Dial(ZAP/g1/12345), I think you cannot group different IAX accounts

Hello, I want to create channel bank in this case: "channel bank" |-----------------------------------------| | FXS,FXO<----->TDMoE<--|---------------------------------->Asterisk |-----------------------------------------| How can it?

I've been experimenting with the zaptel TDMoE stuff and I've got it all working. Calls go from one asterisk box to the other, with no issues, except they don't bring the callerID along with them. I tried the e&m signalling from the wiki and I thought maybe that had something to do with it, so I just changed it to half fxsks and fxoks and that didn't help me any, I still

Hi All, Please bear my ignorance but what is TDMoE used for? Illustrations with practical applications, scenarios or set ups will be most appreciated. Thanks Luan

Hi guys, Can somebody help me on some questions please ? If I have a VoIP network with my Asterisk platform in Europe, what do I need to interconnect my VoIP network to another network in the USA in order to my customers in Europe be able to call to customers in the USA network ? The network in the USA is not an Asterisk platform. Thanks,

Hi All, Just a little over thought. Sorry if someone already asked about this before. Is it possible to put all 16 Ports of E1 in One Asterisk Server ? And if it's not possible is there any suggestion or alternative for me to use more than 320 lines of outgoing calls on One Asterisk Server ? Thanks ZH -------------- next part -------------- An HTML attachment was

I am planning to configure * box A with PSTN interface to route faxes to * box B (running spandsp) over TDMoE. I am using 2xGb bonded NIC's for connection between servers. Was wondering - does anybody have experience with TDMoE over bonded interface - ie. does it work ok?. - does anybody have feedback using this scenario for fax? another question, perhaps someone knows what's the

Hello, I've been using TDMoE accross 2 * boxes for months. It was working well, but * would crash when anyone would try to connect via h.323. So, I got the latest CVS release and compiled without h.323 support. After I made and installed the latest CVS the TDMoE channels stopped working. They have been working great (especially after we got echo cancel working them, thanks Mark) and the

Has anyone on the list used a Soekris engineering PC as a TDM - Ethernet bridge? For example something like a net4801 with a TE110p in it and then using TDMoE to get it into a bigger server where the call processing proper will occur. Anyone know if it might handle a quadspan card ok? (no transcoding, just pure PRI to TDMoE bridging). Craig

Just a Question. I would like to know if TDMoE follows specifiaciones of TDMoIP RAD protocol that says that there is a compression of 16/1 when you do TDMoIP. Manuel Marin Garcia TRANSTELCO S.A. DE C.V. Campos Eliseos 9050 B4 – Cd. Juárez, Chih. 32452 - México Oficina: +52 656 692 11 09 – Fax: +52 656 692 1112 - Celular: 915 727 6141 http://www.transtelco.com.mx