similar to: Status-info 1: Signalling C7 / SS7

Hi, Does Asterisk support SS7? Google shows an old new post from Feb. 2002 stating that OpenSS7 would help add SS7 support to Asterisk, but presently OpenSS7 seems to be dead and I can't seem to find anything about it at Asterisk or Digium's sites. What happened? -- Regards, Tais M. Hansen ComX

Hi, there are still some questions to be answered by OpenSS7.com in order to decide, whether E400P-SS7 is a good choice for the asterisk SS7 support. In the meanwhile I'm also in negotiations with another manufacturer (whose name I currently may not tell due to a NDA) of SS7 hardware, who gets likely persuaded to offer a cheap SS7-PCI-card which would be suitable for asterisk. Asterisk users

Hi, I'm looking into support for SS7 and I found an article (http://www.openss7.com/news13022002.html) which says that OpenSS7 supports Linux Support Inc's T400P-SS7 Quad T1 and E400P-SS7 Quad E1 PCI interface cards. It also says that Linux Support Inc is the primary sponsor of Asterisk. However I cannot find these cards on the Asterisk hardware page

Hi, I've posted this question on OpenSS7 mailing list but I didn't get a clear answer. I have a system running asterisk using Digium T400P card. Can this same card be used with OpenSS7 project to carry SS7 links? Is there any difference between these two cards? -- Matteo D'Amato Network/Telecom Administrator Intelco Communication Inc

Hi all, Does somebody know what's new with SS7 and * ? I'm very interested. Is it ready ? I'm prepared to pay if necessary. Thanks, Angel.

>Freddi Hansen wrote: >> with boards from Aculab, we are replacing Aculab boards with Digium >> boards BUT we would need more >> Digium boards IF we could use both Digium and Aculab cards in the same >> server. The reason being that >> TE410P doesn't support SS7-ISUP so we continue using only Aculab cards >> in the servers that must support >>

Hi, Is this card the same as the T410P, after all, it's made by Digium. There's one prior reference on the mailint list[1] but it didn't answer the question. There was also an SS7 status report[2] last June but it's doesn't seem to have lead anywhere either. There was post saying an SS7 release was immenent last September[3], but then silence. Any info anyone would like to

Does anyone know of a device that will take an SS7 link and convert it to a PRI? -- respectfully, Joseph - (606) 477-2355 x140 ------=============

Hello.. I have a customer who wants to connect 2 PBX's over IP.. The setup should look like this: [PBX] <-- SS7 --> [Asterisk] <-- IAX --> [Asterisk] <-- SS7 --> [PBX] Since there are no SS7 cards , I was thinking at a way of carrying the E1 data as bulk...Can I do that ? How ? Is possible a scenario like this ? I'm thinking of IAX because I don't

In reference to an old post from 2002: http://www.marko.net/asterisk/archives/0203/0103.html How does one go about doing this? Also, what is the present status of the OpenSS7 stack in Asterisk? What can it do now? And is there any possibility in the future of developing a DS3 card for it, if only for the purpose of mostly DACSing? Which is still a level of intelligent call control on the

Has anyone tried to get dialogic ss7 trunking to work with Asterisk? I did some googling but nothing helpful turned up... Could a person get an intel dialogic and get * to see it like a zap channel? And use it for incoming and outgoing trunk access? -- respectfully, Joseph ------=============

I hate to bring this thread back to life, but... > it may be possible to get it supported, do you think the price >point is remotely competitive with Digium hardware? Also as I am not >about to divulge my information to them to look in the downloads >section, what is the licensing of their SDK? What is the licensing of >the driver? > >Steven >On Tue, 2002-11-26 at 14:52,

Hello. I am new to this forum. If this issue has been discussed already, please inform me, but my STFW have indicated that it has not. If SS7 were available on * would it make commercial sense to use it? There are case studies on the web (courtesy of the Death Star :->) for ISPs with 10,000+ subscriber lines showing clear cost savings in transitioning from PRI to SS7 controlled IMT. My

> > >On Thu, 2003-11-13 at 16:50, Freddi Hansen wrote: > > >>>> >Freddi Hansen wrote: >>> >>> >>>>> >> with boards from Aculab, we are replacing Aculab boards with Digium >>>>> >> boards BUT we would need more >>>>> >> Digium boards IF we could use both Digium and Aculab cards in

Hi all I installed DAHDI Version - 2.6.1 DAHDI Tools Version - 2.6.1 libss7-trunk Asterisk 11.0.1 from source on Fedora 12 x86_64. Now i`m unable to load chan_dahdi and libss7: myserver*CLI> module load chan_dahdi.so ?ERROR[10124]: chan_dahdi.c:17842 process_dahdi: Unknown signalling method 'ss7' at line 37. myserver*CLI> module load libss7.so Unable to load module libss7.so

I thought everyone should know this. Jorge, After reading your page in the http://voip-info.org/tiki-index.php?page=Asterisk+SS7 please advise Your U.S. customers that SS7 is not done the same way as in the rest of the world and the requirements are different. The U.S carrier's require 2 redundant links. I know this first hand because we run an SS7 network. CARDOSO Jorge Miguel wrote:

Hi, Would just like to inquire if anyone here has a setup of asterisk to send traffic to AS5400 connected to an SS7-PRI.? this is more of a AS54 question, as i've been reading and i always stumble upon PGW2200 as a requirement to handle SS7 signaling on the AS54. Has anyone able to send calls from asterisk to an as 54 with SS7-PRI without PGW2200? TIA Regards, Nhadie --------------

Hi, I am requesting for a E1 connection from my telco. They are asking if I want DSS1 or SS7, and I am stuck here. Could someone tell me the difference between the two? How should I decide which one to use? Thanks in advance for your help. Mark -------------- next part -------------- An HTML attachment was scrubbed... URL:

hi can someone recommend a book about ISDN and SS7? I've been hacking asterisk for a while, but it'd be good to get some better background within things... thanks roy

Hi all, I'm being requested to deploy an?IVR service?using SS7. I've deployed Asterisk before using ISDN connection, but never with SS7. Can anyone explain me the different between using ISDN and SS7 ? What need I do now to change to use SS7 ?. Many thanks, Giang -------------- next part -------------- An HTML attachment was scrubbed... URL: