similar to: Sending SABME continuosly. Urgent help needed!

Hi Guys, Running the following with a Sangoma A101D PRI card: *Asterisk 1.4.21.2* *LibPRI version: 1.4.10* No inbound or outbound calls can be made. In fact Asterisk CLI doesn't show any activity. Problem goes away on restart of the system or maybe asterisk. I see post about upgrading Libpri to 1.4.10.2 and then I see posts that even that didn't work. Anyone can weigh in this please?

I managed to get Asterisk working with my PBX using T1, now I am moving on to trying to make PRI work. I have my zaptel.conf and zapata.conf configured as follows: Zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone=us defaultzone=us Zapata.conf: [channels] transfer=yes immediate=yes callprogress=yes language=en context=default switchtype=national signalling=pri_net group=1

Any ideas? Sangoma support is closed for the evening. I have the latest Sangoma drivers and Asterisk 1.4 everything installed. When I fire up asterisk, I keep getting "Primary D-Channel on span 1 up" repeated over and over. The B channels never come up. There are no errors in any of the logs, zttool, or the wanpipe tools. Intense pri debug output: < Unnumbered frame: < SAPI:

I've got a couple of PRIs coming in from a SUMA 4 switch with some 800 numbers routed through it. When the calls come in, I get the following message on the console and the call never makes it through: (800 number is fake) Extension '8005551212' in context 'nonauthenticated' from '232102749585' does not exist. Rejecting the call on span 4, channel 1. I do have the

Hi, I hope someone can help me with this.... Asterisk 1.0.6 Zaptel 1.0.6 Libpri 1.0.6, 1 Digium E100P card installed Panasonic TDA200 firmware v2.0.6 E1 Card Firmware 1.0.2 System is located in Australia, so as technologies go, I believe it is twist on the euro standard for the E1 signalling. Here is the situation. The TDA E1 card is set in cross over mode and I am using a functional

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello List, since some days i run into the problem that one span on a TE407P is not comming up correctly. With intense debug on that span i get: < [ 02 01 7f ] < Unnumbered frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] < 0 bytes of data

Hi Guys, Anyone might know why this error keeps showing up and inbound/outbound is not working on a Bell PRI with Sangoma A101D? -- Got SABME from network peer. Sending Unnumbered Acknowledgement No calls can be made inbound/outbound. Keeps repeating. No alarms ON and no changes been made to the system. Stopped all a sudden. Asterisk CLI doesn't show anything with full verbose for both

Hi guys, We are experiencing a problem with a T1 PRI connection. After trying a number of variations in the configuration files, the behavior is always the same: no B channels come up and the D channel doesn't appear to be working well. We can see there are AT&T Maintenance messages being exchanged by asterisk and the provider, CONNECT and CONNECT ACKNOWLEDGE, but that doesn't

Hi, I have the following happen to me after the restart of one of my servers: out of my 3 PRIs (all configured with the same technical settings), the last one isn't coming back. It's underutilized (chances it didn't get a call since my reboot), if it makes a difference . The PRI goes from provisioned to unprovisioned, and I get this regularly: [Jun 22 09:03:48]

So we've got a TE410P configured as E-1. The PRI is showing up as normal, I have green lights, but d channel doesnt seem to come up and i keep getting this error if i do a "pri intense debug" The carrier swears up and down that there are no issues on their end. Any thoughts? localhost*CLI> > Unnumbered frame: > SAPI: 00 C/R: 0 EA: 0 > TEI: 000 EA: 1 > M3:

Ok Guys, I've done a tonne of hunting around on this problem, but can't find much help. I'm running: asterisk 1.4.19.1 libpri 1.4.3 and zaptel 1.4.9.2 which I believe has been modified by RedFone to add the ztd-ethmf module. My interface is a RedFone foneBridge2 4 Span; and I'm connecting to a BT E1 PRI / ISDN30e with 15 lines on span 1, and a legacy Panasonic PBX on span 4. Upon

Hello list, i've got some problems getting a E1 line with a E100P up and running (germany). # cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS/CRC4 YELLOW RED "YELLOW RED" sounds not so good. When launching asterisk, enabling pri debug on that span, i see outgoing attempts: ;---------- snip -------- > [00 01 7f ] > Unnumbered

Hi everyone, I'm trying to get a Sangoma A101D-X card talking to a Sasktel PRI (Megalink) circuit and having some trouble getting it to handshake. Thanks for any help or suggestions to diagnose this problem. The problem is that Asterisk has trouble bringing up the link. I see the following lines every couple of minutes: == Primary D-Channel on span 1 up == Primary D-Channel on

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at

Hi. I'm running some asterisk boxes on different sites, some equipped with a couple of ZapHFC cards, others with Junghanns quadBRI cards. All boxes were compiled with Asterisk 1.2.10 (libpri 1.2.3 zaptel 1.2.6) and bristuff 0.3.0 pre 1s, distribution is Fedora Core 4 with kernel 2.6.17.3 The cards are connected to Telecom Italia's NT1/NT1+ S/T lines; some of them are point-to-point,

Hi list! We currently have a PRI gateway composed by a box with two Digium quad-span PRI cards (a TE420 and a ). One of the cards is filled with TELCO1, while the other has first two slots filled with TELCO2, and 3rd slot with TELCO3. I am currently having (timer ?) issues on TELCO3 (span 7) D-Chan (202 as determined by dahdi_genconf ) is constantly failing causing on-going calls to terminate.

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

Dear; Thanks a lot for guiding me. Is it possible that the installation libpri-1.4.11.5 newer than the libpri-1.4.11.5-patch? Well, when I typed (note: I am trying to apply the libpri-1.4.11.5-patch for the libpri-1.4.11.5): libpri-1.4.11.5# patch -p0 -i libpri-1.4.11.5-patch It gave me that patched detected as shown below (example of one file, and I got same for other files): patching file

Hi, I'm pulling my hair out, cause cannot connect to EuroISDN BRI in Italy with octobri card from Beronet. I use bristuff and have following zaptel.conf... # # This file is parsed by the Zaptel Configurator, ztcfg # # # First come the span definitions, in the format # span=<span num>,<timing>,<line build out (LBO)>,<framing>,<coding>[,yellow] # # The timing

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16