similar to: oh323 0.6.2 q931 messages

Send these questions to Asterisk-Users mailing list. h323.conf ################################################## ; ; Configuration file of OpenH323 channel driver ; [general] listenAddress=W.X.Y.Z ; local ip listenPort=1720 tcpStart=10000 tcpEnd=20000 udpStart=10000 udpEnd=20000 fastStart=yes h245Tunnelling=yes h245inSetup=yes jitterMin=20 jitterMax=100 ipTos=none outboundMax=100

I have tried everything. to register with this gatekeeper to make and receive calls These are the details I received from the voip provider: protocol H.323 Gatekeeper Address - AVS@210.21.118.XXX Port - 1719 RAS - 53 Q931 - 80 h245 - 1722 RTP - 1722 Username - H323 I have 2 phone number/accounts with this gatekeeper that I need to register to. ID - HMA0200.10szxn-xxxx e.164 - 22xx2912

According to the wiki at voip-info.org, the dial structure for using oh323 without a gatekeeper is: OH323/<exten>@<host>:<port> or OH323/<exten> The second option is valid only in the case where a gatekeeper is used. NOTE: OpenH323 library v1.12.0 has a bug in the parsing of the destination host. When this version is used then the above syntax should be:

For the benefit of everyone, having H323 Configuration problem due to H245 Tunnel, check the h323 Config embeded at the end. Comment the offending line as under: ; ; Enable H.245 tunnelling (yes,no). ; h245Tunnelling=yes ; -----Original Message----- From: Tola Ogunsan [mailto:tolaniye@hotmail.com] Sent: Wednesday, May 25, 2005 1:03 PM To: Kanuri, Seshu (Company IT) Subject: RE: oh323 problems

Hi, I've oh323 chan installed and working to make calls from SIP to H323 devices. The problem is can no hear sound with the H323 device. I think this is some related with codecs o nat, because the H323 have one public IP from a different subnet from the asterisk box. If I use netmeeting in gateway mode, the call can be completed and I can talk with a SIP device, but in gateway mode I can not

Hi all, I got serious problem here, I hope I ask on the right place here (sorry if I am wrong). I have used asterisk 1.2.17 with openh323 ver. 0.7.3, for integrating between SIP Gateway and H323 Gateway, it runs about 6 months. But, recently I think it doesn't work anymore...I can't call from SIP Gateway to H323 Gateway. I try to debug oh323 by using : # oh323 debug toggle But I got no

Hello, I've been trying to send traffic to a Cisco Call Manager 3.2, but with no luck. Here's whats happening: * Call gets to CCM * Call gets to the gateway * Rings a couple times on destiny * Call gets hungup. On the CCM I get the following error: MediaManager - ERROR wait_AuConnectErrorInd On the Gw (Cisco AS5300) I get a disconnect cause of 2F (Resource not available) On asterisk:

Hi guys, I've been trying to update my chan_oh323 from 6.1 to 6.3b. I built asterisk from cvs-head on the date Micheal said he made it compatible, pwlib-1.6.6 and openh323-1.13.5 (both with nothing more than the ./configure, make, well aplied patch on openh323) When I start * with my normal config I get this: [chan_oh323.so] => (OpenH323 Channel Driver) == Parsing

I've complied the OH323 .so successfully and can easily receive calls from my H323 gatekeeper (using 711u), however it seems that all outgoing calls are refused and I'm getting "reason 23 (Temporary failure)" as an error code which I can't find documented everywhere. My H323 gatekeeper needs a 001NXXNXXXXXX to dial out to the PSTN even if I'm in north america (Montreal)

Hi there. I thy to compile asterisk-oh323-0.6.3a but it fail in the make command. I have the pwlib-v1_6_6-1 and openh323-v1_13_5-1 as saying in the README file of the packet asterisk-oh323-0.6.3a I do make and this is the error: # make for x in wrapper asterisk-driver; do make -C $x all || exit 1 ; done make: *** No rule to make target `ccflags'. Stop. make: *** No rule to make target

i'm getting Asterisk to dial an h323 call termination service .. right now getting this message: -- Executing Wait("Zap/1-1", "1") in new stack -- Accepting call from '21382890' to 's' on channel 1, span 1 -- Executing Dial("Zap/1-1", "OH323/h323:723@216.52.153.206") in new stack 5:59.330 H323 Cleaner H323

Use oh323. Download the openh323 and pwlib tarballs from openh323.org Follow Jeremy's instructions in the /asterisk/channels/h323/ directory EXACTLY! good luck Regards, Sean Langley, P.Eng Firmware Engineer General Dynamics Canada (403)730-1482 sean.langley@gdcanada.com > -----Original Message----- > From: Senad Jordanovic [mailto:senad@cwcom.net] > Sent: Friday, September 12,

I've got problem with connections h323 -> sip and sip -> h323. I've Cisco 7940 phone with sip soft and Netmeeting as h323 node. As gatekeeper I've gnugk and brand new asterisk from cvs + chan_oh323 0.5.5 When I call from Cisco (SIP) to h323 node by alias registered on gatekeeper and h323 node will answer the phone... I have on my Cisco still Ringing. Call termination, no

What is the difference between H323 and OH323 in Asterisk? I need Asterisk to have basic H.323 support so we can offer some simple H323 termination for some of our Cisco and Quintim hardware. Our upstream provider uses SIP, so I figured I'd use Asterisk as the go-between. I already setup Asterisk so it can push calls out through our providers via SIP. I just need a good/solid/very simple H323

Hello all, It's me again. I would like play with calls between a H.323 client and a SIP client through * inside my LAN. For that, on host 192.168.1.20, I use GnomeMeeting (GM20) and Asterisk; on host 192.168.1.25, I use SJphone (SJ25) as SIP client on Windows and I register into * with a username, no password. The 3 files oh323.conf, sip.conf, extensions.conf are in attachment. In the same

I am trying oh323(version 0.67) , make call from sip UA to h323 gateway, can't get Call-id pass from sip UA to h323 gateway, h323 always gets call-ID sent from Asterisk as *. are there any configure to pass the correct call-id from sip UA to h323 gateway? or this is a bug in oh323 0.67? how about oh323 0.73 ? Mario On 9/29/05, Kanishka Somaratne <kani@technoportal.biz>

Hi all, i've installed the a new pwlib (1.5.0) / oh323lib (1.12.0) on my *. Then i've installed the new chan_oh323 (0.5.6). when i try to make a call with "netmeeting" through * ( * dial out with "Dial,OH323/${EXTEN}@xx.xxx.xxx.xx" ) the call will be blocked. Before, there was chan_oh323 0.5.5 and pwlib(1.4.11) and openh323(1.11.7) installed, and it worked. Is here

i am trying to make calls between two workstations using netmeeting and asterisk. i get the popup on both when i call the extensions 665 and 667 but when accept, i get this error *CLI> 0:18.190 H225 Caller:8112978 H225 Received connect PDU. 0:18.288 H245:810b388 H245 Read error: Bad file descriptor 0:18.318 H323 Cleaner H323

I am trying to compile the latest channel drivers Can anyone tell me what is wrong ./check_ver /usr/src/pwlib pwlib ./check_ver /usr/src/openh323 openh323 gcc -shared -Wl,-soname,liboh323wrap.so -o liboh323wrap.so wrapper_misc.o asteriskaudio.o wrapendpoint.o wrapconnection.o wrapper.o wrapcaps.o make[1]: Leaving directory `/usr/src/asterisk-oh323-0.6.2/wrapper' make[1]: Entering directory

Hello everybody, I?ve been trying to solve a problem for several weeks now but it really beats me. There are several hard phones connected to an Innovaphone 3000 VoIP gateway. On the other side I have a SIP softphone connected to Asterisk. The problem I have is that on incoming calls (hardphones to softphone) I only have outgoing audio (from soft to hardphone); everything is OK when I call the