similar to: Cisco 7940 doesn't register

Hi, I'm trying to detect and or log the duration a a conference (Meetme). I need it in order to do some billing for theses services. Any ideas on how to do it? I googled around but found nothing. Thanks in advance epablo -- Pablo Endres <epablo@comvoz.com> ComVoz Communications USA: +1 954 343-2085 Ext 199 Venezuela: +58 212 7713195 Ext 199 Colombia: +57 1 3256840 Ext 199

Hi people. I've been having some audio problems with some of my cisco 7940 phones using firmware 7.1. The sound gets gargoled up, I can't understand much of what is said (listing on the IP phone). My setup is the following: 7940 - * - Cisco 2621(GW) - T1 I'm using SIP and g729 for all stages of the communication. I was using ulaw for the leg between * and the Gw, but some guys on

Hi, I've installed dovecot-0.99.10.5 using the rpm from Dag Wieers, but when I start it all I get is nothing (but none of the processes are running). I checked the config file and set it up (I'm trying to use it with mysql support, but it doesn't work with traditional config) Any ideas -- Pablo Endres <epablo at comvoz.com> ComVoz Communications USA: +1 954 343-2085

Hi, This post may be a little off topic but I've seen lots of good ideas com from the list, so here it goes: I'm in the need of replacing Cisco Call Manager 3.2 that I have working as my primary GK. I thought I could replace it with gnugk, but it lackes some of the functionality that I need: 1.) Route retrying. If a call placed on a route fails for some reason try other routes 2.)

Hi, I've got a strange behavior on one of my new extentions. This is what I got: extensions.conf with to #includes: extensions-manual.conf & extensions-db.conf I have around 50 users and 100 contexts in these files. I reacently included one: (created from db) [marcela] include => Common include => VoiceMail include => marcela-extensions [marcela-extensions] ;; =======

Hi guys, I've been trying to update my chan_oh323 from 6.1 to 6.3b. I built asterisk from cvs-head on the date Micheal said he made it compatible, pwlib-1.6.6 and openh323-1.13.5 (both with nothing more than the ./configure, make, well aplied patch on openh323) When I start * with my normal config I get this: [chan_oh323.so] => (OpenH323 Channel Driver) == Parsing

http://asterisk.bkw.org/diff/cdr_odbc.diff Now this should fix it the proper way. bkw PS: Thanks for the info klasstek! > -----Original Message----- > From: asterisk-dev-admin@lists.digium.com [mailto:asterisk-dev- > admin@lists.digium.com] On Behalf Of Pablo Endres > Sent: Wednesday, May 19, 2004 3:30 PM > To: asterisk-dev@lists.digium.com > Subject: RE: [Asterisk-Dev]

Hi, Has anyone made a successfull instalation of cdr_odbc?? I've install unixODBC-2.2.8 (made my own RPM) and then built the module. I'm trying to send the cdrs to a M$ SQL server. The sql connection works because I can do any query via isql. When I do the calls I get the following output on the asterisk console: -- Executing Hangup("SIP/test1-a5e1", "") in new

Does anyone know about a good documentation on the oh323.conf file. There are a bunch of paramters that I don't understand. Thanks in advance Pablo -- Pablo Endres <epablo@comvoz.com> ComVoz Comunications

Hey all, I have an as5300 I use for dial in customers, we have 4 PRIs on it. We have a few free channels on it. I'm wondering if I setup SIP on the as5300 I can have asterisk use the free channels for dial out. I'd still have to use my TDM04B for incoming calls, but at least I can expand my outgoing. Anyone done anything like this before? I've never messed with VoIP on Cisco

I agree, any platform suffers when it is extremely difficult to implement. What we need is an interface that does everything we need and shows what asterisk is capable of, a lot of features will go unused because you might not know the exist unless you hunt them down in the source or conf files. I trained on an Avaya INDeX switch it had a complex console but was laid out in a structured way a

Hello, I've been trying to send traffic to a Cisco Call Manager 3.2, but with no luck. Here's whats happening: * Call gets to CCM * Call gets to the gateway * Rings a couple times on destiny * Call gets hungup. On the CCM I get the following error: MediaManager - ERROR wait_AuConnectErrorInd On the Gw (Cisco AS5300) I get a disconnect cause of 2F (Resource not available) On asterisk:

Yes. Tim Thompson http://www.amatechtel.com (806) 722-2227 -----Original Message----- From: CW_ASN - Gus [mailto:cw_asn@fibertel.com.ar] Sent: Wednesday, October 22, 2003 1:12 PM To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Meetme Do you have ztdummy or zaptel device in your system? ----- Original Message ----- From: "Panny Malialis"

Hi, i'm having another problem I can't work out - make for x in wrapper asterisk-driver; do make -C $x all || exit 1 ; done make: *** No rule to make target `ccflags'. Stop. make: *** No rule to make target `ccflags'. Stop. make[1]: Entering directory `/usr/src/asterisk-oh323-0.6.1/wrapper' ./check_ver /usr/src/pwlib pwlib ./check_ver /usr/src/openh323 openh323 g++ -Wall

All, I have access to a Cisco AS5300 w/ 4 T-1's and a Cisco 3600 with no boards. I was wondering if it would be possible some how to Have one of these Ciscos in-between our sip phones and the asterisk server so that we could use G729 Codec. Sip Phones (7960's & ATA's) via G729 -->Cisco Gateway-->Asterisk via G711. Any ideas? Has anybody done such an implementation or know

Hi, I have installed Elastix 1.5.2 (Barranquilla, Colombia (TELCO: METROTEL)) with a TE220P (2xE1) and TDM2400P (16FXS), openr2 is included in 1.5.2 version. The outcoming calls are ok, but with incoming call i have an error: ERROR*[*14972*]* chan_dahdi.c: Chan 2 - Protocol error. Reason = Multi Frequency Cycle Timeout, R2 State = Seize ACK Transmitted, MF state = Category Request Transmitted,

for inbound calls, i can register context = from-sipphone register => 1747xxxxxxx:passwd@proxy01.sipphone.com but how do i configure to make outbound calls to them? exten => _1747XXXXXXX,1,GoTo(dial-sipphone,${EXTEN},1) .... [dial-sipphone] ; ; SIP to sipphone.com ; exten => _X.,1,Dial(SIP/${EXTEN}@??????) ^^^^^^

I am trying to install the package boss but i am getting error below: Please advice install.packages("boss") --- Please select a CRAN mirror for use in this session --- CRAN mirror 1: 0-Cloud 2: Argentina (La Plata) 3: Argentina (Mendoza) 4: Australia (Canberra) 5: Australia (Melbourne) 6: Austria 7: Belgium 8:

Hello, I've been trying to setup a site library that allows the users to manage the R packages themselves, but am having an issue with permissions. As seen below, when installing a package using install.packages, the umask used is always 022. Instead, I would like it to be 002, allowing any user to update packages that were installed by another user. Can someone explain how to get

I am trying to install the package boss but i am getting error below: Please advice install.packages("boss") --- Please select a CRAN mirror for use in this session --- CRAN mirror 1: 0-Cloud 2: Argentina (La Plata) 3: Argentina (Mendoza) 4: Australia (Canberra) 5: Australia (Melbourne) 6: Austria 7: Belgium 8: