similar to: sip device discussion and reviews

Hi, Just received recently released Grandstream handytone 286 ATA for testing. I can call ATA from any other extensions and conversations seems to be of quite good quality. However placing calls from ATA is not possible at all to any extensions. After dialing there no indications of any kind from ATA at all. It just "hangs in there". ATA is behind NAT, registers to an * with public IP

Anyone noticed the snom 360 indications are incorrect for US zone? menu->preferences->tone scheme->usa indications.conf: [general] country=us extensions.conf: exten => 1111,1,Answer exten => 1111,n,Playtones(dial) exten => 1111,n,Wait(30) exten => 2222,1,Busy exten => 3333,1,Answer exten => 3333,n,Playtones(busy) exten => 3333,n,Wait(30) hit speakerphone on the

Hey, all. Got an SNOM 820 in the other day to kick the tires. As with many phones, provisioning it was a bit of a PITA. The biggest problem, as far as I could tell, was that their firmware just doesn't seem that stable, and is sometimes hard to get to. - I managed to corrupt the firmware twice; fortunately, instead of bricking the phone, there's a fairly easy-to-use "rescue

Hello Everyone, My company is about to deploy * as replacement for our existing commercial Altigen PBX. Meanwhile, I've been trying to find the best cost effective SIP VoIP phone which we can use in office for 20-30 employees, as well as a few remote staff. Normally I wouldn't post about a VoIP phone, however, this phone was released less than a week so I thought I'd give some

Hi All I have a snom 200 phone here which works perfectly when using the handset to playback the voicemail messages etc. However when I play back the voice using the speakerphone it sounds choppy. Anyone had this problem before? Regards Mark

Hello Everyone, My company is about to deploy * as replacement for our existing commercial Altigen PBX. Meanwhile, I've been trying to find the best cost effective SIP VoIP phone which we can use in office for 20-30 employees, as well as a few remote staff. Normally I wouldn't post about a VoIP phone, however, this phone was released less than a week so I thought I'd give some

Hi, What is out there in terms of SIP enabled handsfree speakerphones? Looking for something that works well and also fits a low budget. I am used to using a Cisco 7940. It is a great phone but a bit expensive. Thought about the Polycom SoundPoint 300 until I realized that it does not include speakerphone functionality. Thanks, Adi

Hi List, I cant seem to find the setting that changes this! You put a person on hold, they are on hold like normal, but after a few seconds the phone will then start having dialtone coming from the speakerphone, really weird!! Anyone know how to fix this? I see where it could be nice, but in this case, we just want them on hold is all, no dialtone! Any help would be great! Thanks! Ron

We are looking to deploy asterisk at one of our locations that will have about 50 phones. I have been buying different phones to test there quality and feature set. So far we have a Grandstream 2000 Grandstream HandyTone 488 Cisco 7912 Polycom SoundPoint IP And we are looking at getting a Linksys SPA-942 Anyone have a favorite? -------------- next part --------------

I am trying to get the handytone 286 to make a very simple call to * and having problems. It registers with * just fine, but when I place a call (to echo test, for example), the RTP stream seems to have problems opening. Here is there error I get in *: WARNING[98311]: File chan_sip.c, Line 464 (retrans_pkt): Maximum retries exceeded on call 20d1c411-e210-5f3d-3f88-19035c8fcb26@192.168.2.6 for

I'm considering a situation where I buy about twenty ATA devices. I've played with the Linksys / Cisco PAP2T, and got that working fine with some inbound and outbound faxing. The web GUI was okay. I'm seeing prices around $45 to $50 for this thing. It comes with two FXS ports, but I only need one FXS. I've seen the Grandstream Handytone 286 online. It looks promising as an

Hello, I bought a Grandstream Handytone 486 to forward incoming calls from our old analogue PBX to the asterisk server. My first test was connecting an analogue phone to the Handytone and calling a sip phone - worked. Now I used the same cable to connect the line port of the Handytone to the analogue pbx. When I call the number of the analogue PBX I hear a clicking inside, but the call

Hi, On my linksys/sipura phones/ATA, there is a setting called "NAT Mapping Enable" and another called "NAT Keep Alive Enable" These settings must be on in my setup so that my phones/ATA remain connected to my * server. My setup is: Home LAN - Pfsense (NAT, Dynamic Public IP)- Internet - PFsense (1-to-1 NAT, Static public IP) - Asterisk server. I was wondering:

Our basic system is as follows: P4 3.0 Ghz w/ HT, 1GB PC3200 RAM, 120 GB HDD, RH 9.0 OS, * from CVS several weeks ago, working OK for routing, VM, and AA, calls in on separate PSTN lines to Adtran TSU 600, into * server through T100P card. The hardware is not taxed at all with little over 20% proc utilization ever, low mem use, etc. All Phones are SNOM 200's with various firmware revisions

Hi ! On Cisco 7960 (with or without 7914 add-on module) when I press speakerphone button (or select line with line button - which automatically put second line on speakerphone) after about 15-20 seconds of dialtone Asterisk stable dies (seg fault). Tested versions of Asterisk are 1.0.2, 1.0.3 or 1.0.5, chan_sccp is newest form CVS of chann-sccp.sourceforge.net ). Firmware of 7960 is

Question for other snom 200 users: 1. We have horrible sound quality regardless of the codec we use in the phone or specify in *. Has anyone else run into this early on and found a software fix? 2. Speakerphone will not work for playing VM messages, it chops the message into unintelligible fragments of audio. Any ideas? 3. Initially we have horrible introduction of background noise into the

HI Guys, I am trying to use the RTPPage application on asterisk 1.4 using the Snom 320's?? My goal is to do the paging using a multicast IP address. I tried the app_rtppage.c and i can only do unicast on the snom's and i was unable to do a multicast. https://issues.asterisk.org/view.php?id=11797 http://svnview.digium.com/svn/asterisk?revision=101218&view=revision My dialplan

I have been playing with asterisk for a couple of weeks now and I have been very happy with its performance. However, I have run into a problem with how I want to deploy this solution. I have a mix of softphones (SJ and Xlite), ATA's, and a couple of IP phones (Snom 190). The asterisk box is on the public network. For my primary users they will reside behind a watchguard 4500 firewall.

Maybe I'm loosing my mind but I've just noticed that if I put a call on speakerphone and I press speakerphone again it hangs up the call, you would expect it to take the call off speaker back on to the hand piece. I'm using V 1.0.5.22 firmware. Is there any other way to turn off speakerphone I'm missing? Cheers, Dean -------------- next part -------------- An

Hi I have a analog phone connected to my Gateway Handytone and registered to Asterisk 1.4 I have configured my HandyTone 488 (in the section FXS Port) for make and receive calls, however I can not transfer a call when it come via PSTN. But, when a call come from via IP I can transfer it. [phoneanalog] type=friend secret=XXXXXXX context=local nat=no qualify=yes host=dynamic dtmfmode=rfc2833