similar to: Module nonsense (zaptel, wcfxs and wxfxo)

Is there anything special needed to load up a TDM10B card?? I got the card today.. Took it from the box, put it into a PCI slot.. connected the power to the card and booted the PC.. I have removed the X100P to avoid confusion and I have the following in the config files.. in /etc/zaptel.conf # For the X100P #fxsks=1 # For the TDM10B fxoks=1 in /etc/asterisk/zapata.conf [channels]

I am finding that I have to increase the txgain in zapata.conf to 8 when my X101P is connected to my BT phone line, otherwise people can hardly hear me. This then gives echo issues. Do other people have the same problem on BT lines. I was wondering if I should give BT a call and get them to increase the gain on the line. Strange though as the rxgain is OK and I don't have this problem with

I need to reopen this discussion because it's impossible to run spandsp (and VoIP) under these circumstances. With zaptel unloaded, I see the following "vmstat 1" output: no swapping, an occasional disk output, +/- 1003 interrupts/sec., less than 10 context switches/sec., CPU idle 100%. A very quiet system. I load modules zaptel and wcfxo, and the system utilization stays the

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

hi guys, i got a TDM400P FXS card an everything is fine except for this when i do modprobe wcfxs , the linux shows 2 TigerJet Network Inc Model 300 128k. i don't know why it is showing 2 of them. or is that what it is? ERROR: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 0 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 0 cshould be

Hi, I got my TDM11B and am trying to get it to work on my PC. However, I'm having difficulty getting the wcfxs driver to load. I've Googled this problem, and while there are others who have ran into the same problem, none of the solutions work for me. I would very much appreciate it if you could suggest things I could try to resolve this problem. Details follow. The PC is somewhat

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

Hi all i need urgent help our entire switchboard is down only 5 days after it came up. this is the second time this has happened and i am thinking that asterisk is not worth the trouble it gives. mostly it runs without hassle. but around 2 weeks ago during the test phase we rebooted the machine and did the normal modprobes and this error popped up. coming back to work after the weekend the

So I decided to update my code base from the cvs tree. rebuilt everything reinstall everything when I do a modprobe wcfxs or modprobe wcfxo It complains that I have the FXO and FXS statements backwards. Note well: This was a functioning system prior to the CVS update. I do have 2 FXO cards and 1 FXS (4 port with 1 module) card in the system. They are on seperate IRQ's if I set

OK, I've spent way more time than I wanted to on getting an x100p clone to work in Australia. I'm happy to consider other (more functional) options. Does anyone have an opinion on both the Sipura 3000 and other Digium cards (like the TDM400P)? I need something that works with no much fuzz. I know the Sipura 3000 is cheaper the the TDM400P card. All I need is to channel my POTS line

*** Now you just need a "phone" or "station" (FXS) device and a method of connecting it. *** So... essentially I need to spend another $125 US on a Wildcard TDM400P so I can plug in an analog phone? On the X100P description it says: "The X100P supports FXS Loopstart and "Kewlstart" (Loopstart with far end disconnection supervision). It can detect ringing and

With one IVR payment system, I noticed quite a difference in DTMF transmission between these two cards. The IVR missed nearly all digits from X100P, while receiving digits from TDM fine. Since neither card process or synthesize audio, what can the difference be? (This particular IVR has problem with some regular phone devices, too.) Yuan Liu

I am still having unacceptable echo on my X101P and twidling with the rx/tx gain levels and echo settings appears to have no discernable effect. Some questions for those who may have more significant electrical engineering background than I. 1. This impedance match thing ... will it affect this solution having other phones in parallel with the X101P? This is done so that I can test while not

I am considering a G5/XServe for a conferencing system. I need to put a TDM card in the machine for timing. Is anyone out there using Asterisk on Mac with zaptel drivers? I am looking at using Linux for the OS. If so what is your experience? Have a great day! Geoff

Hello, I have configured my TDM01B Card (1 FXO Port ) as follows (below) but it will not pick up an incoming call. Any suggestions/tools to see what the problem is? I have looked at zttool where this line changes but I don't understand what it means (The last digit changed from 0 to 1) Total/Conf/Act: 4/ 1/ 1 /etc/zaptel.conf fxsks=4 loadzone=nl defaultzone=nl

Hi All, I'd really like to see a show of hands with regard to people's experience with FXO interfaces. I own a few X100p cards and have had nothing but problems with them. I also took part in Sipura's beta program, for the SPA-3000. While it can be an improvement over the X100p, it presently has echo problems that make it unusable. Sipura has not acknowledged the problem ( at least

Hi all, I've struggled for several days trying to get a Digium TDM04B 4-port wxfco card working on a Dell 1U PowerEdge 750 machine running Fedora Core 1. I finally got a call back from Digium who indicated that there is a fundamental conflict between the card and the PowerEdge having to do with PCI interrupts. Asterisk version is stable v1-0 12/29/04. The symptoms of the problem were as

I know the X100P cards are not supported by Digium any more, but for home office use, are they still acceptable? I have two POTS lines, one residential and one business line comming into the house. I'd like to get both into my * server and $15 total compared to > $100 for the newer TDMxxx card sure is desirable. Having said that, will the sound quality, functionality, stability, etc. be as