similar to: Fwd: hdlc and kernel 2.4.26

All, I am trying to configure hdlc support on T100P Digium card - everything seems ok... but it just does not work at all. I was able to compile all drivers, the light on the card becomes green when I plug T1 link.... but I even can't ping default router IP... there is no data coming back to me, so I am confused completely now. Also I tried both protocols - raw hdlc and cisco hdlc. The

Dear All, we have installed a TE410P card on a Dell Poweredge 1750 running a slackware 10 with 2.4.26 Kernel. Then we have made two loops on the card and we have configurated all the 120 channels. Our goals was to perform some stess tests even if in this scenario we used the same box as generator and target. The stress test comprised to generate up to 60 calls at the same time by placing a file

Hello, Can anyone out there confirm as in "Yes I am doing this right now" that this can be done? I know that the stuff from 2.6 was backported to 2.4.26 - and it works there (so says the wiki) but before I buy a bunch of hardware (or don't buy hardware, depending on how you look at it) I would love to know. Thanks! -- Kristian Kielhofner

I have a pair of sites tied together with a T1 line running zaptel PPP on either end. The system works, but I keep getting these messages in the kernel logs, and users are reporting connection problems (TCP timeouts, and hangs) especially under high usage. --snip-- HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC

I have 2 servers, configured identically. Each has a TE405P and 2 PRIs. One server was experiencing crackly audio on one circuit, accompanied by HDLC bad FCS messages. The telco recabled and moved me to another port on the DMS-100. The audio is better, but there are still bad FCS problems on the span. I have moved the PRI in question to the other server, and the problem does indeed move with the

I've read as much as I can on this error and still can't seem to figure out what's causing this error: Jun 23 20:54:58 NOTICE[7483]: chan_zap.c:7395 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Jun 23 20:55:03 NOTICE[7483]: chan_zap.c:7395 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Jun 23 20:55:03 NOTICE[7483]:

All, I'm having a heck of a time getting hdlc to work on kernel 2.6.11.9 .. I compiled hdlc, hdlc_gen, hdlc_cisco, hdlc_raw, into the kernel (note into, and not 'modules'). System comes up, I configured zaptel.conf span=1,0,0,esf,b8zs nethdlc=1-24 modprobe wct4xxp ztcfg sethdlc hdlc0 cisco ifconfig hdlc0 up All of this works fine, believe it or not. I have a T1 cross plugged

Hello All, I am battling a problem I don't know how to fix... Here is the scenario: Fractionated T1 with 1-6 channels voice, 21-24 channels data. Comes into a box with Digium T100P, splits off data channes with HDLC, to devicec pvc0, This works fine, but I have a routing problem getting to my machines! Here is the current set up... sethdlc hdlc0 fr lmi ansi sethdlc hdlc0 create 44

Hi list, I can successfully build the driver modules; hdlc, dlci, syncppp, and lmc from the 2.6.18-128.1.14 kernel source rpm, and have managed to create a 'wan kmod' rpm. It all works fine for IPv4, but now I need IPv6 for ppp connections, which doesn't work for me. I think I'll need to back port Krzysztof Halasa's 'ppp for generic hdlc' patches to the

Hi!, this issue makes me crazy. I read a lot of docs, also * mailling list and I try a lot of things without success. Any help will be appreciated. Here is the info: Hardware: -------------------------------------------- Supermicro Server with motherboard X7DB8, chipset Intel 5000P, Xeon 5050 Digium TE110P Software --------------------------------------------- Asterisk version 1.2.12.1

Hi fellow asterisk users, I am running Asterisk 1.4.29 with an Digium TE121 card (wcte12xp kernel module) an approx. 100 snom320. The whole installation is running without issues since 5 months. Without having changed anything on the asterisk server for at least 2 months, i noticed "clicking sounds" at external calls over the PRI. Asterisk constantly throws the following messages: ...

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

Hi, After upgrading to DAHDI 2.4.0 from Zaptel, I noticed a lot of HDLC errors on my console: [Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 [Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 These errors prevented calls from being made and received on my PRI spans. This seems

I have a new client who is about to order an Integrated PRI T1--eight voice channels and the remainder data. He's not sure whether Qwest will provide a router to split the voice and data. I remember we had a lot of trouble with HDLC in Linux kernels past 2.4.19. Have those problems been fixed in the 2.6 kernel? Will I be able to split the voice and data channels using zaptel?

Hello all, My set up is a fractionated t1, with 1-6 voice channels, 21-24 data channels. I have a t100P installed in a amd 1500 with 512meg. Question: In order to set up the data channels, is the following correct? 1) compile new kernel with generic hdlc support 2) compile hdlc from hq.pm.waw.pl/hdlc 3) uncomment KFLAGS+=DConfig_ZAPATA_NET in zaptel makefile 4) compile zaptel, 5 compile rest

I have the same problem in a box with 2 HFC-PCI, but i already remove the row in modprobe.conf and load the module manually. Both cards works fine Any idea ? Giordano -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Julian J. M. Inviato: luned? 27 giugno 2005 12.04 A:

I receive this error on the asterisk console and it is pretty much ALWAYS coming up. Sometimes there will be a break where it does not display. We had our PRI provider test the lines and they claim that there is no signalling problem. It doesn't matter if there are no calls or if there are 10 calls in progress the error is still displayed. I also get an annoying popping or clicking sound

Hello, I get an Error every minute on the second card of two installed TE410P Cards in our System. The error is: PRI got event. HDLC Abort (6) on Primary D-channel of span 5(-8) PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 5(-8) Is it possible that there are known problems with 2 cards in one system? I'm running Asterisk/Libpri/zaptel from SVN branch-1.2-16008 I was

Hello, I've got a running system in which logs are full of messages such as: [Jun 10 07:24:14] NOTICE[2414] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 The strange thing is those messages are coming from a single span. My setup is : Asterisk 1.6.1.18 Junghanns OctoBRI with wcb4xxp driver libpri 1.4.10.2 dahdi 2.3.0 3 BRI lines in PtMP mode What does this

Can any give me or point me to a short and simple explanation of what HDLC is?