similar to: Chan CAPI and Latest CVS wont compile

Hi, I am trying to install chan_capi, with asterisk (cvs) on Suse 9.0, but I get the following error: ====== linux:/usr/src/chan_capi-0.3.1 # make gcc -pipe -Wall -Wmissing-prototypes -Wmissing-declarations -g -I/usr/include/asterisk -D_REENTRANT -D_GNU_SOURCE -O6 -march=i686 -DCAPI_ES -DCAPI_GAIN -DDEFLECT_ON_CIRCUITBUSY -DCAPI_SYNC -Wno-missing-prototypes -Wno-missing-declarations -DCRYPTO

Dear All, I have a working asterisk installation in the UK on BRI point-to-point. I am using Redhat8 with one Eicon Diva Server 2.0 card with chan_capi-0.3.5 and Asterisk 1.0.1. I have got to the stage where I can make and receive calls over ISDN. My question: How do I group the 2 B channels so that when one channel is in use, the other channel is availble to receive[make] an

Hello, while testing the following scenario, I ran into trouble: One * box with two AVM active controllers in Point-to-Point-Mode is connected to another * box with ZapHFC/Quad-BRI cards using bristuff in NT-mode. All is working fine, I can call from one box to the other and vice versa. But if I'll cut one line, it is not possible to place an outbound call from chan-capi accross the still

Hello all, I just subscribed to this list and I hope this is the correct place to ask for help with this issue. Today I checked out asterisk via cvs and I was able to compile, to install and to run it. Everything was fine so far. Then I downloaded chan_capi 0.3.3 from www.junghans.net and tried to compile it, too. Unfortunately I get an error in line 1205 when compiling chan_capi.c : too

Hello all, I've just finished to install chan_capi with 3 AVM Fritz PCI cards. It correctly loads the 3 drivers, and * starts without errors. immediately after * start, audio quality is really fine, but, after the first incoming call, all incoming audio is broken, trembling and stuttering.

Hello, AFAIK the feature CD (call deflection) is only possible on point-to-multipoint links, is this correct? I've heard about the feature "partial rerouting" which should do the same on point-to-point-links. Is this implemented in either bristuff or chan-capi(-cm)? Thanks in advance, Karsten

Hi List, I'm having a problem with detecting incoming dtmf tones with chan_capi, using an AVM Fritz card. I have set up softdtmf and relaxdtmf, both to 0, expecting that the capi module will detect the tones, but it did not. I also set both to 1, expecting that the asterisk dsp functions will detect them but it did not either. Can anyone provide any ideas how to overcome this issue?

Since upgrading from stable to latest cvs I can't place CAPI calls (AVM Fritz/chan_capi-0.3.1) Did I miss something that has to be changed in configfiles? Also tried to recompile chan_capi which run into an error. capi info shows me: Contr1: 2 B channels total, 2 B channels free. Any suggestions to these logfile snippets jo ---------------------------- * to ISDN -- Accepting

Thanks to ww and his patch on bug #104, I have successfully implemented Asterisk behind NAT without using STUN or anything crazy. It's quite straight forward. Until this gets tested enough and put into CVS, you will have to patch your chan_sip.c file to do this. I'm sure within the next few days this will get put merged into CVS if no one finds any problems. I tried this on chan_sip.c

Hi! This weekend we had a problem with our Asterisk Box which ran flawlessly for nearly 4 weeks. The Asterisk server sits between the PSTN and a Siemens PBX and bridges 2 BRI lines. No calls, not incoming, not outgoing. The admin rebooted the Dell Box and then everything worked fine again. Now, I'm analyzing log files to find the cause. During the Asterisk outage the logfiles only show

hi all I'm being spammed by these messages in the console (see below) and sound doesn't work with today's cvs. I rolled back a week, and it works fine. In addition to the sound problems, I had to enable inband dtmf squelch on the dilnk mgcp phones. if not, each pressed key was counted twice NOTICE[245776]: File chan_mgcp.c, Line 710 (mgcp_rtp_read): MGCP ast_dsp_process

I'm trying to compile chan_capi-0.5.4 on Slackware 10, but I have bunch of errors. (By the way, can I use chan_capi for ISDN card with winbond w6692cf chipset?) I'm not a linux expert, still :-) Before compiling, when I type "modprobe capi" to load capi module, and then "lsmod", i get list of modules: capi 6208 0 kernelcapi 30496 1

When we receive or make a call to the outside - they can hear us, but we cant hear them. It may work 1 of 20 times. I have set canreinvite=no and looked at many sites but cannot track down this problem. Current setup: Isdn Eicon Diva card / Capi -> Asterisk --> network. I have tried adjusting the RTP port in rtp.conf with the Cisco default ports, no luck. Anyone had this

Hi, I am calling from a grandstream phone with g723 codec through * to iconnect. Incoming context as well as outgoing context set to g723.1 codec in *. Call get connected and I can talk. However I get the following warning, which scrolls on my screen until I hang-up. [root@asterisk sath]# cat g723.1 - Executing SetCallerID("SIP/-08122ae0", "1001") in new stack --

hi, i have connected a SNOM 200 to the asterisk. here are my settings, Codecs ------- Default codec - g.711u/g.711a Packet size - 20ms Negotiation - Interoperable Type - 160 DTMF ---- Inband - negotiate Outband - negotiate Payload Type - 101 when a call comes to the SNOM or when making an outdial, following warning messages are coming on asteisk, WARNING[1209214400]: File dsp.c, Line 1198

hi ! I have asterisk with Licensed G.729 codec enabled. Whenever I make a call using this codec a warning apears as, WARNING[18450]: File dsp.c, Line 1106 (ast_dsp_process): Unable to detect process 256 frames WARNING[18450]: File dsp.c, Line 1106 (ast_dsp_process): Unable to detect process 256 frames WARNING[18450]: File dsp.c, Line 1106 (ast_dsp_process): Unable to detect process 256 frames

I just downloaded chan_capi.0.3.4a.tar.gz but it will not compile on my system (Suse 9.1). I compiled and installed Asterisk and it is running, did I miss a configuration or dependency for Chan_Capi somewhere ? cheers, Mike linux:/usr/src/chan_capi-0.3.4a # make gcc -pipe -Wall -Wmissing-prototypes -Wmissing-declarations -g -I/usr/include -D_REENTRANT -D_GNU_SOURCE -O6 -march=i686 -DCAPI_ES

What does it mean ?? WARNING[265236]: File dsp.c, Line 1198 (ast_dsp_process): Unable to detect process 2 frames WARNING[265236]: File dsp.c, Line 1198 (ast_dsp_process): Unable to detect process 2 frames WARNING[265236]: File dsp.c, Line 1198 (ast_dsp_process): Unable to detect process 2 frames -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi can anyone help me on this error msg?? dsp.c:1467 ast_dsp_process: Unable to process inband DTMF on 2 frames thnx St

I have read the guides on using Messenger to connect via SIP. I just cant get it to connect, even inside the LAN. I enter <local ip address>:5036, it trys to sign in, but times out and says Service Unavailable. Do I need anything extra in my configs for Messenger to work? Have * admins managed to get this to work? Any help welcome. Thanks