similar to: I have put iLBC at the top

The configuration I'm building replaces an existing PBX with Asterisk. There are 8 existing modems that people use to call in from the outside to connect to PC(s) on the inside to transfer data, etc. Callers access these modems by calling the main number and then dialing an extension for the modem they want to talk to. What are my options for supporting these modems with Asterisk? Here are

Hi All, I've been playing with GSM and iLBC over low bandwidth connections (central Asterisk box with 2mbps, to ADSL users on 512/256) and both seem to perform well. Based upon what I've read in the archives and at voip-info.org iLBC should perform a little better if packets are lost, than compared to GSM. Do you find this to be true in practice, or is GSM just as robust? Whilst

Hello, i want to use asterisk as a gateway for H323-Phones. But i cant get it work. I'm using a gatekeeper on another computer. My IP-phone is registered there. Does anybody can sent me an oh323.conf and extension.conf as examples? Thanks in advance Erik Bastian -- NEU : GMX Internet.FreeDSL Ab sofort DSL-Tarif ohne Grundgebühr: http://www.gmx.net/dsl

I am having some problems with g729 with SIP and ZAP channels. 1) I have two g729 licences. Very frequetnly (I don?t know what triggers the error) I get the following warnings and error when I try to place a call via SIP to my X100P. The only way to get out of this is through a restart of *. When the error ocurrs there are no other calls in place. Any ideas? Error Opening channel:2 not

Hey all, Does anyone know what this means? I was running asterisk fine. Installed it on a new pc and I am using the g729b. codec that is optional. I ran the install for the codec it went ok but when I run askterisk via asterisk -vvvgc it gives me this error anyone know? I make sure I entered in the correct reg number. I followed the steps correctly. Too Registration error! Please try

Perhaps I was a little too hasty in my conclusions of dysfunctional fax on the SPA-2000. It turns out I have a one way audio problem on line one of my SPA-2000. I have all the correct settings according to the comments in the wiki, but the problem persists. However, if I do a hook flash out of and back in to the call that isn't transmitting audio, it works fine. My sip.conf entry for the

Hello, I have modified the VoiceMailMain application to satisfy the request of the "local users", i.e., my wife. She lost patience with too many options (we have one mailbox, so we don't need to forward messages, or reply to messages, or file them in 6 different folders...) So the modified app says "Message 1", reads the message, "Message 2", reads...

Hello list , I?d like to announce possible problems with migrating any version prior to 1.0.2 to 1.0.3. Pay attention : 1. Codecs Codecs names/description have been changed . For example : versions <= 1.0.2 voip*CLI> show codecs Disclaimer: this command is for informational purposes only. It does not indicate anything about your configuration. 1 (1 << 0)

Hi kind developers, I need select soon the best freeware VOIP codec, I see that all competitors are using iLBC because of the separate packets management. How speex behave in case of packets drop? Why other choice all iLBC? Thank you for any kind answer. Best regards. ------------------------------------- Roberto Della Pasqua Http: www.dellapasqua.com Email/Msn: roberto@dellapasqua.com

Hi! As the upstream of my DSL-connection is very slow, I'd like my sip-phones to use iLBC to connect to my *. My gateway provider only allows ulaw. Hence, I'd like to use the follwing setup: SIP-phone <--iLBC--> Asterisk <---ulaw----> PSTN-Gateway I get the following error: "Unable to find a codec translation path from ilbc to ulaw" Setup SIP-phone: disallow=all

I want use iLBC and have following in mind, please help me is it possible ? ISDN <-----(ALAW)-----> * <-----(ALAW)-----> SNOM SIP??<-----(iLBC)----->?*?<-----(ALAW)----->?SNOM 1. ISDN incoming codec is ALAW SNOM codec should be ALAW (can't be iLBC because a lack of codec). 2. SIP incoming codec should be iLBC (snom is ALAW). 3. SIP outgoing codec should be iLBC /snom

i tried asterisk ilbc codec against kphone. when the call got connected, i started to immediately get these kind of message to the console: WARNING[14350]: File codec_ilbc.c, Line 141 (ilbctolin_framein): Huh? An ilbc frame that isn't a multiple of 52 bytes long from RTP (50)? WARNING[14350]: File codec_ilbc.c, Line 141 (ilbctolin_framein): Huh? An ilbc frame that isn't a multiple of

Does anybody know if the updated licence on iLBC makes it safe to include in Asterisk when used in a commercial environment again? https://sites.google.com/site/webrtc/ilbc-freeware It seems to require that the Google iLBC licence document is on the box, but that otherwise it is free-to use by all in any way (BSD licence style). I believe that prior to that there was a requirement to register

Hello all, I've started implementing iLBC on some of the ATAs we have floating around clients' homes, but I'm coming against this error message with most of them: codec_ilbc.c: Huh? An ilbc frame that isn't a multiple of 50 bytes long from RTP (38)? The ATAs in question are various Grandstream models - the HT486 being the predominant one. Looking at the list archives, it's

Hi, I've been trying to get the G.729a beta codec running with my remote Asterisk box that talks IAX2 to my local Asterisk box. Digium fixed the problem I was having in registering the beta codec, so that now works fine. I've removed the old codec_g729b.so from /usr/lib/asterisk/modules and put in place the codec_g729a.so beta from digium FTP. My CVS build of Asterisk is about a

This seems to have been reported before, but I've seen no resolution: http://lists.digium.com/pipermail/asterisk-dev/2003-August/001470.html http://lists.digium.com/pipermail/asterisk-users/2003-August/019091.html http://lists.digium.com/pipermail/asterisk-users/2003-October/024472.html When forcing use of Speex, no sound comes out at all (Speex-1.0.3 on the Asterisk server) When forcing

Hello Folks, I noticed that all of the IaxClient based softphones with exception of Firefly only seem to have support for GSM but what about iLBC? The quality is excellent with iLBC even on a dialup connection! Meanwhile while the audio on GSM often sounds scratchy. Is anyone looking to implement iLBC in an IaxClient based softphone soon? Errol Biz4Web Solutions Limited

I already have ilbc installed on my system. The files are: /usr/include/ilbc/iLBC_decode.h /usr/include/ilbc/iLBC_define.h /usr/include/ilbc/iLBC_encode.h /usr/lib/libilbc.a /usr/lib/libilbc.la /usr/lib/libilbc.so -> libilbc.so.0.0.0 /usr/lib/libilbc.so.0 -> libilbc.so.0.0.0 /usr/lib/libilbc.so.0.0.0 However, if I do a "make" in asterisk-1.4.19, it will not detect that libilbc.a

Aloha, Are there any hard phones that support ILBC? I see lots of soft phones but not Cisco, Polycom etc. Aloha, Matt

I'm having trouble configuring these services the way I want. Basically I prefer using iLBC before GSM, however Iaxtel only want to talk GSM. It _seems_ that Voicepulse prefers GSM also, because even if I put ILBC before GSM in the "allow=" part of iax.conf, if GSM is mentioned, Voicepulse will use it. If I don't allow GSM Voicepulse will use ILBC. Does anyone know how to