similar to: need working loopstart config - t100p

Em (20:59:21), Asterisk Users Mailing List - Non-Commercial Discussion escreveu: >On Tue, Jun 21, 2005 at 08:09:52PM -0300, Alessandro wrote: >> >> Does Somebody know why no load modules to FXS? I used zaptel-1.0.7 >> version. > >What color are the modules? >Post your /etc/zaptel.conf > >-- >Mike Mike, The color is green, red ans bluw. Link

After speaking with several people, and even participating in a forum of several other people with echo issues, I thought I'd share what we've done (well actually what our chief R&D engineer, Brett Bourn has done...) First let me say that normal cheapy PC hardware couldn't be made to function with out echo. We tried on both the single port Digium T1 card and the 4 port Digium T1

zaptel compiles fine (make linux26) but when I modprobe ztdummy I get the follow error. [root@localhost zaptel]# modprobe ztdummy Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for ztdummy System info: Linux localhost.localdomain 2.6.9-5.0.5.ELsmp #1 SMP Thu May 19 19:24:44

Hi All I have problem with LIBMFCR2 for once Exchange I using Sangoma card, the firstly. my ssystem run successful with MFCR2, connected to E10 (Acatel Exchange), after that, i move connection connect to EWSD (Siemens), my system don't work. error protocol R2. my system: Asterisk CVS 1.1.X LibMFCR2 pre.005 and unicall-pre.005 this's my setting and my setting wanpipe1.conf

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not lit. Should I be seeing

I am setting up a box with a T100P. Everything is going well. The company I am working with has their one phone switch gear. They provisioned me a E&M Wink T1. Cannot do PRI unfortunately. We chose E&M so we could pass an unlimited number of DIDs to the trunk as apposed to FXS loopstart signaling. I can make outbound calls no problem, but I am having problems with the dial plan for inbound

I just purchased a T100p from digium and a Carrier Access Access Bank 1 channel bank (12fxs/12fxo). I have the setup partially working thanks to some help from IRC. However I still have the following issues I can't seem to resolve 1. When calling into the system from the PSTN call hangup is not detected. * leaves line in use until it is shutdown. 2. When calling an analog phone connected to

I am having a problem with Red Alarms on X100P cards. The most frustrating thing is I can not duplicate the alarms, therefore am not sure how to solve it. I have read after searching posts and the web that you can try different signaling methods which may help alleviate the problem. There is fxsks (Which I am currently using), fxsgs, and fxsls While reading the Digium site about these different

I need to create a couple of tie lines between a legacy system and an Asterisk system. I was told that the tie lines are E4 Superframe E&M. I have done E&M wink but have no idea about E4 Superframe E&M and Google is not helping me here. Does anyone know about this type of signaling and if Asterisk can handle it? Thanks, Steve

Hi ! I am connecting to Adit 600 thru a T100P card I have configured 1-16 FXS channels and 17-24 FXO. Everything looks fine on Asterisk side I get a tone on all FXS channels, but when I try to dialout thru one of the FXO channels 17-24 it doesn't connect to the POTS line and echoes back my voice. I use fxsls and fxols for the T1 channels and ls on Adit side. Whats wrong here ? here is my Adit

I have an nec electra elite 192 with a t1 card; and am looking for suggestions as to integrating them (can't throw out the system yet!). I have a fully working asterisk server -CVS-04/27/04-19:01:05- (found a hp d220 for $350.00!), 2 digium t100p cards, a plain t1 with loopstart signaling, and 2 working bt102 grandstream ip phones (thanks again Matt for your "start from scratch"

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf

I figured it out. The old system (Televantage 3 and 4 I think) has limited specifications on the T1. After setting up the system, I was able to send and recieve calls. I still have some work to do like figuring out faxing and a floating receptionist, but this is a nice start. ----------------------------------------------------Televantage T1 Requirements: Framing: D4 Superframe or Extended

I have a problem which I need to resolve. We are trying to put an asterisk between a Mitel PBX and the world. We are adding Voip service via Asterisk. Here is are config files for the settings but our problem is the following. We are able to send calls to the Mitel pbx and it's the T1 connections is green saying it's ok. The support department from Mitel said that they use e&M and

Hi, I've connected a two T100P from digium with a 2 Rhino channelBank. Everything is working as expected. but I have occasional Falls, asterisk take 99% of CPU resources, with the following report May 24 14:52:41 WARNING[11441]: We're Zap/1-1, not H8?F??n** May 24 14:52:41 WARNING[11441]: We're Zap/1-1, not H8?F??n** May 24 14:52:41 WARNING[11441]: We're Zap/1-1, not H8?F??n**

I could only get *ANI*DNIS* working one way and that was setting my signalling type on the Asterisk side to 'featd' The Definity won't send *ANI*DNIS* information back to the asterisk as far as I can tell. Other than that, I've been running it with wink/wink E&M for a while now. TN464 circuit pack on the definity side, te110p on the asterisk side. Just a crossover cable

Hello I have installed my new E100P card in the same machin with two TDM04B cards. I have followthe instructions on http://www.digium.com/index.php?menu=configuration#T_E100P_PRI This is my zapata.conf span=1,0,0,cas,ami fxsls=1-15,17-31 dchan=16 fxsks=32-39 loadzone = us defaultzone=us I do *modprobe zaptel wct1xxp wcfxs ans seems to work ok. * But when i do ztcfg -vvv i got Zaptel

Sorry to post such a newb set of questions but I have been hammering about trying to get Asterisk running on FC2 machine reading everything available (I think that is what stuffed me, shouldn't have read it all :-) ). Config FC2 running Asterisk 1.0.0, with the h323 compiled in and installed correctly. Amazingly enough I have everything compiled correctly and installed. I am running a