similar to: * & ISDN-BRI-PTP & DID & ISDN4Linux does not show incoming number

Hello, I just got my isdn-card working together with i4l and asterisk. Everything seems to be working fine: I can accept calls coming from the outside and I can dial out. Even setting the msn works like charm but my problem is that I cannot hear a word. There's complete silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network

Hi to everyone! I am new to this list and i want to greet you all! I am trying to install Asterisk on a Fedora Core 3 Distribution with a Digi Datafire Micro V ISDN Card. I know that I have to use the ISDN4Linux so in modem.conf I set the I4l driver ,the msn and device. Modem.conf [interfaces] context=remote ;driver=aopen ; modem by AOpen driver=i4l ; isdn4linux - an

Hi all, Here another guy working with ztdummy and having problems with music. MP3Player does not work for me both from a telephone entering through a passive ISDN-adapter as well as a SIP-client in the LAN. Ztdummy works with conferences. Here are my messages. I have seen several discussion threads in the mail-archive regarding this subject, but could not find an answer. Is this something I

G'day, New to Asterisk alert! I have a Netjet card running on linux 2.4.27 kernel using the HiSax module, and trying to use it for incoming/outgoing calls from *. I've tried playing with modem.conf and extensions.conf every which way I can think of, using samples and whatever I can find off the net, and I get the same message everytime I try to dial in. The complete message is:

Hello, I am trying to use 2 netjet cards under asterisk and isdn4linux. I am having a hard time trying to get them to work in terms of dial out. Does anyone have a working config I could look at for even one card (tried that, not much luck either). When i dial out: -- Accepting AUTHENTICATED call from 172.16.11.2, requested format = 2, actual format = 2 -- Executing

hi, i installed asterisk and works very well, the only problem is that when i try to call a direct number of a company that has a normal PBX i got this error: to 10.8.210.153:5060 == Accepting call on 'SIP/a.sampietro-f7be' (a.sampietro) -- Executing Goto("SIP/a.sampietro-f7be", "doisdn|BYEXTENSION|1") in new stack -- Goto (doisdn,00115601992,1) --

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

Hi all, this is a rather "newbie-oriented" question, so please bear with me... The system running Asterisk has been provided with an AVM FRITZ!Card PnP. SuSE Linux 9.0 recognizes it right after booting the system and it seems to be configured (MSN) correctly... The hwinfo looks like this: --- pbx:/etc/asterisk # hwinfo --isapnp 11: ISA(PnP) 01.0: 10300 ISDN Adapter [Created at

Hi, my setup is quite simple: an asterix CVS of 2003-11-15 on a 2.4.21-debian-5 GNU/Linux box in an internal network (192.168.1.0/24, asterisk is 192.168.1.10). - with a SIP phone configured as 192.168.1.190, and with its SIP server being 192.168.1.190 - with an ISDN AVM c4 i4l card on an ISDN connection with 2 channels. I try to: - dial-in from ISDN, then transfer to the SIP

hi I have a passive isdn port configured in modem.conf in extention.conf i use this two channel (ttyI0 and ttyI1) with the string: exten => _NXXXXXXXXX,1,Dial,Modem/g1:${EXTEN}|60|r how can i hide my msn? is it possible to activate the clir with the @ before the ${EXTEN}? thanks Cristian

I'm trying to use an hfc based pci card with asterisk but every call fails falling in the congestion extension. exten => _0.,1,Dial(${TRUNK}:${EXTEN:${TRUNKMSD}}||tr) exten => _0.,2,Congestion Looking in the syslog i can see: isdn: HiSax,ch0 cause: E001B it seems that this is a terrible error when arrives... hard to tell what is the cause. Also terrible is finding a lot of material

hello, does anybody know how to setup avm fritz pci card in p2p mode ? regards marian -- SUNTEQ s. r. o. Hviezdoslavova 9 # Prievidza # 971 04 # Slovak republic Tel: +421-46-5430 754 # Fax: +421-46-5439 144 http://www.sunteq.sk/ ------------------------------------------------------------ A mind is like a parachute... it only works when it's open.

Hi, Apologies in advance for the lengthy email. I'm new to asterisk and have trouble with isdn4linux. The setup is very basic like this: winxp ------- asterisk -------- winxp x-lite | x-lite | pstn The hardware involved is: Compaq EVO with RH9/kernel 2.4.20-30.9. Fritz!Card PCI v2 Asterisk CVS-04/17/04-21:36:18 Basically

I have a North American BRI configured as National ISDN (NI-1) on an SBC (Nortel?) switch. SBC calls this "FastTrak ISDN", and it's surprisingly inexpensive -- less than two POTS lines. I've been trying to find an inexpensive PCI interface solution to connect this to Asterisk as voice lines. I prefer ISDN BRI over POTS lines because of the improved signalling, fast dialing,

Hello all, This afternoon I had a BRI line installed by Telstra (our telco in Australia). I'm using an Eicon Diva 2.02 PCI ISDN card with the isdn4linux driver. Incoming and outgoing calls with Asterisk work fine (and with no echo - my main reason for getting ISDN). However, I can't seem to get outgoing DTMF working (incoming works fine). I made a call from my desk phone (Cisco 7940G)

Is any way to limit music on hold (or ringtones) to specified time ? I need it to play it ~ for 7 seconds . How to do this ? in dial plan i have: exten => _021XXXXXX,4,Dial,Zap/1/BYEXTENSION||r when go to this extension it rings once! and then asterisk say : -- Zap/1-1 answered Modem[i4l]/ttyI0 and it stop ringing ;) becouse mean that other end is ringing :) .. BUT when the other

I have asterisk loaded and seemingly working with 4 snom 200 phones. I cannot dial in or out using a DIVA isdn card When I dial out i get "not found xxxxxxx" on the handset. When I dial in i see in /var/log/message isdn_net: Incoming call without OAD, assuming '0' isdn_net: call from 0 -> 0 1856 ignored isdn_tty: Incoming call without OAD, assuming '0' isdn_tty:

Hello, I try to use Asterisk with an Eicon-card called "DIVA Server 4BRI-8M PCI" but I don?t get it to work. I?m running on RH8.0. The Eicon-card supports isdn4linux. In the modem.conf file i have put following: ----------- [interfaces] ; By default, incoming calls should come in on the "remote" context context=remote ; Modem Drivers to load driver=i4l ; Type of dialing

Hi, I have a problem that I just can't figure out how to solve. I start *, dial it using a ISDN phone over PSTM, to a Hisax card installed in * I get the demo-greeting, listen for a few seconds and hang up. I dial it again, but this time the first second is sound from where the previous call ended, then the greeting starts as it should. Right now I have removed all codecs but codec_gsm.so

Hello, Does anyone know what driver to use with an "Eicon Diva Server 4BRI" card? My modem.conf: -------------- [interfaces] context=remote driver=i4l msn=16453 device => /dev/ttyds01 -------------- I get the following error: -------------------------- == Loading modem driver chan_modem_i4l.so => (ISDN4Linux Emulated Modem Driver) WARNING[8192]: File chan_modem.c, Line 383