similar to: 183 Session in Progress

Hi, does anybody made G723 or G729 to work with a GrandStream Phone ? I've a Cisco here and it works fine with G723, but not with my asterisk. The bandwitdh is very important, since we will have our extensions at home. I know that I have what I pay, but the phone works with cisco. Trying to use G723 or G729 Asterisk says no codec available. Does anybody have it working with any compression

i have been trying to get a newly liberated (from vonage) cisco ata-186 (sip ios v3.1) working properly with asterisk. my client is behind a linksys wrt-54g, which up to this point hasn't proven to be a problem (i have several sipura spa-2000's and polycom phones working just fine behind them). (i'm running cvs-head from yesterday). after looking at the various suggestions,

Hey all, I have an as5300 I use for dial in customers, we have 4 PRIs on it. We have a few free channels on it. I'm wondering if I setup SIP on the as5300 I can have asterisk use the free channels for dial out. I'd still have to use my TDM04B for incoming calls, but at least I can expand my outgoing. Anyone done anything like this before? I've never messed with VoIP on Cisco

Hello, I have 5 digium's g.729 codecs and succesfully register with asterisk, I have incomming call from my cisco AS5300 to Asterisk through IP. But Asterisk always use g711 ulaw instead of g.729. When I disable all other codecs other than g.729 in both cisco and asterisk, calls get dropped once connected. The codec list show on my cisco AS5300 for g.729 are: g729r8 g729br8 I suspect that

Hello, We are working on implementing a solution for a medium service provider. They were previously using a Cisco AS5300 gateway with some PRI trunks to receive modem calls, then route them out the Internet. The Telco they were buying the trunks to discovered this configuration and restricted them due to legal conventions, and stated that in order to continue doing this, they would have to talk

Greetings, I am attempting to configure an AS5300 to provide a SIP based gateway to the PSTN from Asterisk. I have been unable to identify through the docs how specifically this should be configured in Asterisk and have not been able to get things working through trial and error. I am sure I am missing something fairly obvious here but any guidance (or example cfgs) would be much appreciated.

All, I've found problems in my setup with the latest couple of revisions (1.135/1.136) of asterisk/channels/chan_sip.c In my setup I have a RH9 asterisk server, AS5300 (single E1 to PSTN) and a dozen 7940's, everything is in the same VLAN and only running SIP. Outbound calls work fine: 7940 -SIP-> Asterisk -SIP-> AS5300 But inbound calls fail, I see the initial INVITE from the

Is it possible to terminate calls via SIP on a Cisco AS5300? Did anyone do it? How? Do i need an special IOS version? Ive been trying to compile the OpenH323 channel for the last month, but errors still happens. Thanks in advance. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi Now, my Cisco AS5300 sent call to my asterisk, but two problems: When i call the phone number, i have: [Oct 28 06:01:16] NOTICE[12813]: chan_sip.c:18160 handle_request_invite: Call from '' to extension '0426000000' rejected because extension not found. [Oct 28 06:01:18] NOTICE[12813]: chan_sip.c:18160 handle_request_invite: Call from '' to extension

Guys. I need some advice on some h323 issues. I need to test connectivity from Asterisk to a Cisco AS5300 that has PSTN lines and to cisco 3600 voip routers. H323 needs to be used here but I was wondering if anybody has linked Asterisk to these Cisco routers before? Thank you for any pointers.

Hello all, When I generate an out-going call from *, the DTMF detection is not working ? ASTERISK --> GW AS5300 --> PSTN But the DTMF is working correctly when it's an incoming call. PSTN - -> GW AS5300 - -> ASTERISK Well, I tried with the 3 dtmfmode of asterisk inband, rfc2833 and info, no way !!! Is it normal that asterisk try to setup the outgoing-call using ULAW ? if I

Hi folks, The obligatory newbie disclaimer: "Hi, I'm new to Asterisk and I have a couple questions..." OK, now that that's over with: I've just started working for a small CLEC, and I'm trying to sell * to my boss as a replacement for some expensive/inflexible/closed-source software he's been using to provide residential dialtone with for a couple years now.

Hi everyone, I'm new to the list, so I apologize if this is a trite question. We're an ISP with a barely used PRI, and also currently use asterisk with POTS service on an audiocodes gateway. We have a notion that we want to take on a new revenue stream, with our model being as such: 1) Convert one of our PRIs into a two way voice/data bundle. 2) Plug this PRI into a piece

Hello all, I have a cisco AS5300 which is register with a gatekeeper and a Asterisk server also register with the gatekeeper. PSTN ---->AS5300 ---->Gatekeeper ---->Asterisk I set up a conference room on the Asterisk sever (Room No 1234). I try to call from PSTN to AS5300, The AS5300 will call the Asterisk server through the gatekeeper. I manage to get to the start of the conference

I'm confused a bit about the following and was hoping to get some answers on this group - What is exactly implied when we say asterisk can connect to a PSTN. Does it mean connecting to the PSTN via PRI/T1/E1? If yes, then I assume asterisk does not need to do any SS7 signaling and all it does (playing the role of a PBX) is to connect to a Class 5 Switch at the CO. Is this a correct statement?

Hello, I have a Cisco AS5300 connected to Asterisk (1.6.2.9) Between 15-16 minutes, the call is disconnected without reason. Here is what is displayed in the debug: Received an SDES from 10.4.0.10:17399 -- Got SIP response 420 "Bad Extension" back from 10.4.0.10 -- Stopped music on hold on SIP/as5300-1-0000004d == Spawn extension (dialin, 065939191, 2) exited non-zero on

Hi all, I realize this is OT. I just got a Cisco AS5300, and I need to configure it like such: Asterisk -----(H323/SIP)------> Cisco ----- (E1/PRI)------->Telco So calls originate from the Asterisk side (registered users on SIP or just ZAP phones), and they go out H323 or SIP to Cisco, where they go out PRI. I have the Asterisk side sorted :) (either H323 or SIP), I need help in the

Hi guys. We have currently Asterisk CVS-v1-0-08/15/05-15:53:48 connected in SIP with a Cisco AS5300 (IOS 12.3). One PRI is connected to the Cisco gateway. The problem we have is that on incoming PSTN calls to the AS5300, relayed in SIP to Asterisk, the callerID name is not being transmitted. We received the callerID number but no name. I know we are receiving the name from the PRI in

hi All Any body already setup asteriks call routing to Cisco AS5300 with SIP Server ? i need informations sample config for that, or can show how to route docs . thanks Dirgan --------------------------------- Meet your soulmate! Yahoo! Asia presents Meetic - where millions of singles gather -------------- next part -------------- An HTML attachment was scrubbed... URL:

I've done some reviewing of the archives for G729 and H323 experiences. The landscape of that query isn't pretty - lots of pleas for help, and nor do I see too many "answers." I have a pending bid that requires some data before I can implement * on this particular solution. My question is perhaps a slightly differently worded one than has been asked before, but it may be