similar to: VoiceTronix V4PCI and Digium TDM40B together

Ron, VoiceTronix worked with me last week and backported the new chan_vpb that's in the current HEAD CVS tree to the 1.0 stable branch. So if you are using 0.7.2 or 0.9.0 you can go to the VoiceTronix website now (note that this is very new) and download an Asterisk package. When you download it there is an new chan_vpb.c that needs to be put in your asterisk source code tree. Also there

Is anyone using the VoiceTronic Openline4 PCI (fxo) card? I am trying to setup Asterisk using a Digium 40B (4 port fxs) and an OpenLine4 (4 port fxo), however I can't find any examples or post that utilize this card. I have my stations (Sayson 390) ringing each other, but haven't had any success ringing out. I have the OpenLine4 loaded and all of the new drivers working good, just

I am wandering if anyone can explain this unusual scenario. I am running Asterisk on Fedora. After the box boots, I run insmod wcfxs at a command line. The phones keep the red message light on and are in a state like they are not recognized yet. If I then run the command ztcfg, I don't get anything after the command, meaning that everything should be OK in zapata and zaptel confs and the

Owias, The 537 is, for the most part, a drop-in replacement for the Digium card. Please search the archive and the Wiki, as there have recently been several discussions about this exact subject. To my knowledge that is about the only modem that works, but keep in mind it is _not_ supported. That being said, follow the instructions on Digium's site for installing the X100P and you should be

Hi. I need help with my brand new Voicetronix OpenLine4 board that I installed into Asterisk. After building the Linux device driver and inserting the module, I modified the /usr/src/asterisk/channels/chan_vpb.c file to uncomment the US settings and comment out the Austrailian ones. I made the appropriate entries for routing in vpb.conf and extensions.conf.... All appears to be well, except

Hi all, I think I've got the V4PCI card working with asterisk (can't tell for sure, can't dial out since the card doesn't appear to understand 2 or 3 dtmf codes, if you've seen that before, let me know). Has anyone else had problems/successes with those cards before though? Thanks, Andrew Griffiths

Hi we've got Asterisk CVS-HEAD 18-Aug-04 (modified by Voicetronix as available on their site for use with the vpb driver) and an OpenLine4 (4xFXO). The same server also has two X100P. Calls on the Voicetronix card drop instantly when the called party picks up. The vpb driver reports that it detected a hangup (loop drop) yet there is no hangup when connecting the X100Ps or analog phones to

dear Hackers, i have a voicetronix Openswitch card, and i have been finding it very dificult to get it to work with asterisk. i intend to connect 8 ports to the PSTN and 4 as station ports. problem 1: On running asterisk all i get at first i get : event[9=>[11] station OFF hook] on vpb/1-12 even [12=>[11] loop drop on vpb/1-12 event [12=>[11] Tone detect:GRUNT event [2=>[11] Dial

hi there, i've been able to successfully run asterisk with the Voicetronix OpenLine4 card, it can accept calls and function normally. The only problem I'm experiencing so far is getting the card to outdial to a third party. What I'm trying to achieve is basically call bridging, where the caller dials in to asterisk, some IVR plays and then attempts to perform a "transfer"

Has anyone gotten the voicetronix boards to work with Asterisk, what would it take? Or does anyone know where I can get 4 ports or more fxs PCI cards that do work with asterisk? Brian J. Schrock Network Engineer, RHCE, CCNA Anistone Technologies Phone: 614-798-9106 FAX: 614-573-7165 6926 Avery Rd. Dublin, OH 43017

http://www.eweek.com/article2/0,1759,1591131,00.asp bkw -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040514/165456d3/attachment.htm

Hi all, Trying to get fax reception going using a voicetronix openline4 card, however, there are two issues (as far as I can see) (1) Currently the voicetronix world (cards, firmware, drivers, channel prog etc.) does not do fax tone detection. I have spoken to the voicetronix guys , understand what has to happen there and may do some hacking if I can resolve the second issue. Meanwhile, I

Any guidance on how to get my openline4 to get recognized by asterisk@home? I've got my vpb drivers running, but not sure how to add it as a trunk, should it be via zap? or is there another way? Thanks, Chuck

Hello all - I'm trying to get Asterisk working with an Openswitch/6 card with all ports set to FXO for PSTN in/out, and 10 SIP phones on the LAN with the Asterisk server. The SIP phones are working properly to dial one another, but I can't seem to get a call to go out to the PSTN through the voicetronix, and I similarly can't get incoming calls to the lines hooked up to the

Hi All, Just a quick question, but I could really use some help on this one. I've got the CVS-Head of * installed and running, and am using a VoiceTronix OpenSwitch12 to connect to 12 analouge lines. I've got callerid activated by the Telco, and can get callerid using a std phone. However, using *, I always get an error 'Cannot decode callerid'. Does anyone know if I need to

Hi all, I used to have an OpenLine4 card, but decided against using it due to some problems with hangup detect. Does anyone on the list actively use Voicetronix's OpenSwitch12? What are your opinions on the card? Cheers, Flynn

>From what i've read i think that asterisk is suppose to generate the dialtone. But when i pickup my analog phone it seems that the Openswitch12 card is the one playng the dialtone. Im almost positive the card is playing the dialtone, can anyone confirm this? And if so how can i change the dialtone?

Hello all, I hope this is not off-topic, if it is please let me know. I'm currently playing with an Asterisk at home, in order to get to know it's ins and outs. Very very impressive indeed. I've got it hooked up to my home phone line via a Wildcard clone board (Intel modem with Ambient chipset), and it works like a charm. Zaptel picks up the card as a generic clone, and works with it

Hi All, I recently installed and compiled Asterisk in a Red Had (enterprise) box with digium TDM400P card installed in it. Thanks to the good documentation available, I was able to install and configure the hardware as well as software. As specified in the Getting Started with Asterisk Guide, I first installed zaptel driver, then libpri and finally Asterisk. All of them successfully compiled, but