similar to: Pots Extensions

Hi All: I'm a newbee to Asterisk. I currently working on a project and want to know if Asterisk does support R2 Signaling. Thanks Begra8fl >From: asterisk-users-request@lists.digium.com >Reply-To: asterisk-users@lists.digium.com >To: asterisk-users@lists.digium.com >Subject: Asterisk-Users digest, Vol 1 #3647 - 9 msgs >Date: Tue, 04 May 2004 13:32:00 -0500 > >Send

I have: RedHat 9.0 TDM40B asterisk-0.9.0 compiled from sources zaptel-0.9.1 likewise /etc/zaptel.conf contains fxoks=1-4 loadzone = us defaultzone=us loaded modules zaptel and wcfxs /etc/askterisk/zapata.conf contains [channels] language = en signalling = fxo_ks context = phones channel => 1-4 /etc/askterisk/extensions.conf contains [general]

Hi, I recently purchased two X100Ps and a TMD40B. I have set everything up according to the instructions however I can't get asterisk to pick up an incoming call (It just keeps ringing). Also, when I pick up an internal extension I get dead air. I searched the mailing list for 3+ hours -- What am I missing? Thanks in advance for your help. Here are the installion steps that I used:

I have TDM40B, TDM04B cards, 4 analog and digital phones. First I want to use 4 analog phones with my TDM40B card. I would like to dial between 4 analog phones. The dialing numbers for 4 analog phone will be 800,801,802 and 803. These are my conf files. /etc/zaptel.conf fxsks=1-4 fxoks=5-8 loadzone = us defaultzone=us ;;;;;;;;;;; /etc/asterisk/zapata.conf [channels] relaxdtmf=yes

Hi, I have a running asterisk 1.2.1 (bristuffed) with a TDM400 Board. Connected to 1 port is am ordanary Fax Machine. Everything 'seems' to work, however receiving faxes is very unreliable. Sometimes I receive a normal page, without problems. Sometimes half of a page and the rest is scrambled, but most often, I receive nothing and the other site reports a Fax error... The Fax machine

I have a serious problem that repeats very often, after 30 - 50 calls and I can only solve it by stopped and restarting * :-( After a while, * seems to loose track of something. When an ISDN call from PBX needs to go to the Telco, I get 'Ring requested on unconfigured channel 255/255 span 2' It's always channel 255/255 ??, the 'span' number is random Setup: * between Local

Firstly, the problem... Ever since I installed and setup asterisk, I have had various problems, initially it was echo caused by the ISDN (isdn4linux) card I was using. So, I upgraded to the X101P from digium. I still had echo, so I figured it was also caused by the ATA186 (cisco) I was using. So, I upgraded again to the TDM40B quad FXS card. This solved pretty much all my problems, except

Hi all, I've been trying to wrap my mind around this one for several days now. How can I 'debug' the CallerID reception on a Zap/POTS channel? I have a POTS line with CallerID and a Digium TDM11B card right now. I have my signalling set to ks for both sides, can make and receive calls just fine. But I never get CallerID on incoming calls. I get the following messages: Aug 11

Hello. New to the list. We're in the process of deploying Asterisk. Actually, we're going live tomorrow, and I just found out that my Zaptel cards have been mis-configured. I'll preface this by saying that I have looked in the wiki, read through the samples, and attempted to call Digium (they're closed.) So I'm praying that someone on the list can help me out! I have two

Hi all, We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap modprobe wcfsx then the ztcfg output this: Zaptel

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi, I had ordered a TDM40B and developers kit a few months ago. I have everything installed and working, with one exception - sound quality. When placing a call it sounds like a very bad cordless phone - lots of hiss / static in the background. This even happens with the dialtone, though it is much worse one the call is connected. This does not occur when the phone is directly connected to the

Hi all, this time with the complete configuration files... We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap

Hi All, I'm attempting to use two X100P cards and one TDM400P card. What driver do I load for the TDM400P? Is their any documentation for this card yet? Also, I know this has come up before but I can't seem to find it in the archieve... how do I configure the second X100P card? Anyone have a working sample? Thanks in advance, Randy

I am having problems getting a Nicherons TDM400P wildcard clone to dial out. Everything appears to be configured correctly, but although I see call progress, it never seems to actually pick up the phone. (The following is a test of 911 emergency, where I substitute 811 [repair service] as the actual number dialed.) *CLI> -- Executing [911 at from-internal:1]

I got this nice TDM22B with two green modules left and two modules right /var/log/messages shows: Nov 26 23:47:48 dns kernel: Zapata Telephony Interface Registered on major 196 Nov 27 00:37:53 dns kernel: Freshmaker version: 71 Nov 27 00:37:56 dns kernel: Freshmaker passed register test Nov 27 00:37:56 dns kernel: Module 0: Installed -- AUTO FXS/DPO Nov 27 00:37:56 dns kernel: Module 1: Installed

Two problems, possibly related: Here's the configuration...my Asterisk box has a TDM844B in it; port 1-4 are FXS, 5-8 FXOs. Here are the config files: /etc/zaptel.conf: -------- fxoks=1 fxoks=2 fxoks=3 fxoks=4 fxsks=5 fxsks=6 fxsks=7 fxsks=8 loadzone = us defaultzone = us -------- /etc/asterisk/zapata.conf: -------- [channels] language=en usecallerid=yes hidecallerid=no

Hello all, Normally I just use pri's with our asterisk systems, but a request came in to add some normal pots lines to the setup. We have 3 lines, and they run into the fxs ports. They hit the dialplan just fine, and they always dial the "s" extension. However, my question would be... Is there a way to determine what number was dialed and have it forward to a specific phone? With a

This is, hopefully, just a case of brain fade. With zapata.conf and zaptel.conf in place, asterisk loaded, no dial plan and all LEDS on the card lit, I get no dial tone, plugging an analog phone into ports 1 or 2, only a buzz and click. zaptel.conf - defaultzone=us loadzone=us fxoks=1,2 fxsks=3,4 zapata.conf [channels] signalling=fxo_ks language=us context=phones-1 group=0

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1: