similar to: Asterisk <--> Cisco router

Hello, We have a sip trunk end point with cisco media gateway. VoIP works fine. But when we try to send faxes thru this trunk, we simply can not. Is there anybody experienced such problem and solved? How should i set sip.conf and udptl.conf. I already have t38pt_udptl=yes in sip.conf Thank you.

I see a lot of comments but no actual show runs. Can someone post a 7206 config. I am having a dickens of a time getting calls to pass. I currently have the following loaded. Cisco IOS Software, 7200 Software (C7200-IK9O3S-M), Version 12.3(8)T6, RELEASE SOFTWARE (fc2) Thanks !!! Jerry -- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.344 /

Hello, I've got an ISDN PRI circuit terminating in a Cisco AS5350, which in turn is talking to an Asterisk server via SIP for call origination and termination. Seems simple enough, and it works for the most part, but: 1) Caller ID name data comes in on the PRI, but doesn't appear to get handed off to the Asterisk server via SIP, at least not in any format that Asterisk

We're having an issue with connecting a Cisco ITS installation to * such that DTMF tones are passed to *. DTMF tones aren't passed to voicemail or to any of the interfaces behind *. On the Cisco Side: dial-peer voice 8 voip destination-pattern 9999$ session protocol sipv2 session target ipv4:172.16.1.249 session transport udp dtmf-relay rtp-nte codec g711ulaw no vad We have also

I have the following configuration and am obviously missing something small that is causing * not to work as expected. I have the following defined in sip.conf [ccme-in] type=peer host=10.0.9.1 context=devel_in disallow=all allow=alaw nat=no canreinvite=yes qualify=yes and [devel_in] is defined in extentions.conf However when I try to call via the dial peer I have configured on the cisco

Hi i test a new equipment on my backbone: a Cisco AS5300 with voice dsp ressource connected at a E1 Voice Link. I want that all call incoming on the cisco 5300 are sent to Asterisk and all Asterisk outgoing call are sent to Cisco AS5300. Actually, i configure the AS5300: isdn switch-type primary-net5 ! voice service voip sip ! voice class codec 400 codec preference 1 g711alaw codec

Hello, I'm trying to receive faxes with asterisk. My configuration is like this: PSTN fax -> ISDN -> Cisco router with VoIP module -> Asterisk When I try to send a fax from PSTN fax I got the standard fax signal, Asterisk starts rxfax application and then call ends and there is no tif anywhere. On the fax display there is still one message: Calling... Part of my extensions.conf:

Hi All: I have a Cisco3620 with a proper T1/PRI card installed with asterisk running on the same LAN. Since I have lit up the line, I can dial out and make calls to regular lands lines. However when a call comes back in it rings the destination phone once and disconnects. Here is an error from my router 15:40:45: ISDN Se1/0:23 SERROR: L3_GetUser_NLCB: EVENT 0X45 No NLCB 2 15:40:45: ISDN

Hi all, In my Asterisk setup, incoming calls through Cisco PSTN gateway to Asterisk extensions sounds work fine. All calls can be terminated properly after hangup. However, when calls were forwarded to voicemail, after recording & hangup the PSTN calls and cisco FXO port remained connected unless cisco port was manually shut/no shut. # key used to hang up the call did NOT help. Did anyone

If you have a PRI terminated in a Cisco router talking SIP to * and would be willing to share your Cisco config, please respond. Also, I would be interested in knowing what version of IOS you are using. We are using an NM-HDV in a 3640. TIA Bruce Komito High Sierra Networks, Inc. www.servers-r-us.com (775) 236-5815

Guys. I need some advice on some h323 issues. I need to test connectivity from Asterisk to a Cisco AS5300 that has PSTN lines and to cisco 3600 voip routers. H323 needs to be used here but I was wondering if anybody has linked Asterisk to these Cisco routers before? Thank you for any pointers.

I would think I could do this but for some reason I am stymied. I have a PRI from RCN connected to a cisco 3640 (in my day "cisco" is all lower case :-)). My config looks something like this on the cisco... --------------------------------------------------------- voice-card 3 dsp services dspfarm ! ip cef ! isdn switch-type primary-5ess ! controller T1 3/0 framing esf linecode

List users, It's been a while since I've posted here, but I've been hard at work pushing toward our large scale Asterisk goal and keeping up with this list can be a full time job by itself (I have19,543 unread list messages!!). This Friday, September 16th 2005, my team will be at the MCI Development Lab in Richardson, Texas testing our setup. We have a three server system

Hi i am search a sample config (for asterisk and for cisco) for connect a cisco 1760 with a FXO card to my asterisk. Thanks for your help Jerome

HI, I have been pulling my hair out trying to get a Cisco MC3810 to interface my Asterisk box with a T1. I am able to make outgoing calls but incoing calls never reach my Asterisk box. The cisco give a fast busy when I try to call one of the DID's. When playing around with the dial-peers I can get the cisco to pick up the call, but then it forwards the call back to the ANI that is dialing.

I have 2610 XM with 1 Fastethernet and VIC2-2BRI. Dialin and dialout over pots is ok. Also inbound pots calls get redirected to Asterisk y.y.y.y So far so good. But I want to setup VOIP sessions with local carrier. I added dial-peer 40 for this. Session target x.x.x.x But calls will always get routed to the pstn peers 50 and 60. Peer x.x.x.x is never contacted or tried. My situation: PSTN

Hello, Could somebody tell me if I can connect CISCO 2600 router with support of H.323 to Asterisk ? If it is possible could somebody tell me how to do it. I would like to document it and put on some website so everyone can see it. Regards, -- bart -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, everyone. Right now, we are trying launch our own PBX system based on Asterisk(Fedora) with Cisco 2611. Cisco has 2 port FXO card installed on it. For testing, I have 2611 hooked into phone line with number of xxx-xxx-xxxx fine. (I'll call it F). Using softphone, I can dial in extension 1001 on asterisk, which should talk to cisco. After initial connection to Asterisk, I have try to

Hi. If I use a Cisco as a PSTN termination GW and need to route all incoming isdn calls to my asterisk and all outgoing calls from asterisk via the cisco out to pstn, how do I do that ? in the cisco I have this: dial-peer voice 1 pots destination-pattern [0-9]T no digit-strip direct-inward-dial port 3/0:D ! dial-peer voice 50 voip destination-pattern [0-9] voice-class codec 1 session

Ok here is a question that has gotten me stumped. I have an Asterisk system up and running. I need to connect it via the Internet to a Sip Cisco system. This is what they have. I have there IP address's and login. X-lite is able to connect to them and make a call! So I have the name right! CISCO router model: 2621 VoIP module: NM-HDA-4FXS I have done Google lookup and at the Wiki about