similar to: ZT_CHANCONFIG - function not implemented (38)

Hello all, My set up is a fractionated t1, with 1-6 voice channels, 21-24 data channels. I have a t100P installed in a amd 1500 with 512meg. Question: In order to set up the data channels, is the following correct? 1) compile new kernel with generic hdlc support 2) compile hdlc from hq.pm.waw.pl/hdlc 3) uncomment KFLAGS+=DConfig_ZAPATA_NET in zaptel makefile 4) compile zaptel, 5 compile rest

I realize why leaving email addresses in the archives would definitely _not_ be a good thing. However, is there a way to reply off list to an archived message? I would like to contact 'ulexus' about his asterisk/hdlc setup. Would anyone have his email address? Sorry for the interruption, -- Michael Welter Introspect Telephony Corp. Denver, Colorado +1 303 674 2575

I am running RedHat Fedora Core 3 with their "kernel-2.6.10-1.741_FC3" kernel, and if I use nethdlc in zaptel.conf, when I run ztcfg I get the message: ZT_CHANCONFIG failed on channel 11: Function not implemented (38) Does anyone have ideas on how I can work around this issue? T1 channels 1-10 are voice, 11-24 are data (second board isn't used at the moment). Here is my

Is there a Linux tool that will splice several gsm sound clips together into one clip? In my agi script, I would like to use 'get_data' with one clip instead of multiple 'stream_file' so the user doesn't have to listen to the entire spiel before responding. Thanks, -- Michael Welter Introspect Telephony Corp. Denver, Colorado +1 303 674 2575 mike@introspect.com

Does anyone know of a 24 port ATA device that could be installed in a phone closet? Like a channel bank, but, instead of multiplexing onto a T-1 circuit, it would convert to SIP/RTP on a LAN connection. Thanks, -- Michael Welter Introspect Telephony Corp. Denver, Colorado +1 303 674 2575 mike@introspect.com www.introspect.com

I finally got my ASUSCOM (Cologne chip) ISDNLink card working here in the US. When a call arrives, I get "Unknown IE 42 (Unknown Information Element)" and "Unknown IE 21 (Unknown Information Element)". IE 21 (0x15) is defined as Q931_CALL_STATE_SUSPEND_REQUEST. IE 42 (0x2a) is not defined in the code and I couldn't google it. Is this something perculiar with ISDN in

I need to connect a bunch of analog telephone sets. Does anyone have any comments about this channel bank? Disconnect supervision? Echo? ADSI problems? The price is right @ $995 new and $695 refurbished. Thanks, -- Michael Welter Introspect Telephony Corp. Denver, Colorado +1 303 674 2575 mike@introspect.com www.introspect.com

Has anyone implemented HOBIC SMDR output from *? Can someone point me to the Bell HOBIC specification? Thanks, -- Michael Welter Introspect Telephony Corp. Denver, Colorado +1 303 674 2575 mike@introspect.com www.introspect.com

Occasionally my /etc/hosts file gets corrupted. The IP address and the host name switch positions with the host name to the left. What this happens, my 7940 phones won't register. Fixing /etc/hosts allows the phones to register. Do any of you Linux gurus know who is corrupting the hosts file? Thanks, -- Michael Welter Introspect Telephony Corp. Denver, Colorado +1 303 674 2575

I'm having problems with the voicemail prompts. The beginning of each prompt is garbled. Prompts "edian mail" and "assword" can be recognized, but when it starts on the short phrases it is completely garbled. It is almost like the subsequent phrase starts before the current phrase finishes. I have isolated the LAN to the * box and the phones, so LAN congestion is

Does anyone have a recommendation for a 48 port LAN switch for a new * system? I'm not happy with NetGear's reliability. -- Michael Welter Introspect Telephony Corp. Denver, Colorado +1 303 674 2575 mike@introspect.com www.introspect.com

Hi All, I wish to connect * to a Cisco using a E100P board. When I load the driver I got this error message: -bash-2.05b# modprobe wct1xxp ZT_CHANCONFIG failed on channel 1: Function not implemented (38) /lib/modules/2.4.21-SAX/misc/wct1xxp.o: post-install wct1xxp failed /lib/modules/2.4.21-SAX/misc/wct1xxp.o: insmod wct1xxp failed Follows Cisco configuration: isdn switch-type primary-qsig

my target is to produce a linux router with T100p to Fract T1 24chan to ethernet and TDM 4channel FXO. I have not been able to get nethdlc to work, just get zaptel networking not configured if I set bchan and dchan the card comes to life, but I don't believe this is correct for what I want to accomplish. according to markster@ this is the way they do it. using (multiple distro versions

All, I am trying to configure hdlc support on T100P Digium card - everything seems ok... but it just does not work at all. I was able to compile all drivers, the light on the card becomes green when I plug T1 link.... but I even can't ping default router IP... there is no data coming back to me, so I am confused completely now. Also I tried both protocols - raw hdlc and cisco hdlc. The

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed

I went on a service call yesterday to find an asterisk system with a T100P card on a Qwest PRI and a TDM40B card connected to fax machines. The TDM40B LEDs were not lit, and the system did not respond to keyboard input. However, calls were being processed for the PRI and 7960 phones. I replaced the TDM40B card with a new one, and the system now seems to be ok. But I'm wondering, why

I believe it is not fiber, but I am not sure. I am going to take one of them home tonight and hook it to my POTS line there, which for sure is not fiber. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Michael Welter Sent:

Hello everyone, We have recently turned up a new T1 from McLeod (Midwestern CLEC). It is configured like so: /etc/zaptel.conf: loadzone=us defaultzone=us span=1,0,0,esf,b8zs ;(also tried 1,1,0,esf,b8zs) bchan=13-23 nethdlc=1-12 dchan=24 /etc/zapata.conf: switchtype=national context=pri-in signalling=pri_cpe group=1 channel => 13-23 I can get hdlc0 (and pvc0) up just fine after the

I've seen other posts about this problem, but I haven't found a solution. I'm dumping eight call files into the "outgoing" directory at one time. Three of the calls are successful while the other five are lost. Here is the call file: Channel: Zap/g2/3036701917 MaxRetries: 1000 RetryTime: 60 WaitTime: 45 Application: TxFAX Data: <filename>.tiff|caller Note: All

Just when I thought I couldn't be wrong, I was wrong. We have woodpeckers that drill into the arial telephone cables, and water seeps through the holes and partially grounds the tip and/or ring wires causing hum. I thought the hum/buz on my lines was a telco problem. The Qwest HQ noise team assures me that my lines are within spec. Sure enough, when I listen on the test set the lines