similar to: Messengers calls dropped (SIP problem?)

Can someone help me what went wrong with this call? This call was initiated from dev/ttyI0 device on my asterisk server to mediatrix unit. Mediatrix unit user received the call and call started. I can hear them OK but they can not hear me correctly (cut-off sound, noise). Call was finally hunged up. Can anyone point out if there was something wrong? -*CLI> sip debug SIP Debugging Enabled

My Cisco 7905 can't register with Asterisk (1.0.7-BRIstuffed-0.2.0-RC7k on Debian stable). It could, however, register with another installation of Asterisk and the settings on the phone (apart from the SIP proxy address) haven't changed since then. On the new Asterisk box my sip.conf contains this: [jeremy] type=friend regexten=801 allow=g729 host=dynamic secret=PASSWORD nat=yes

I am interested to learn if I need to have ztdummy installed if I do not have any zaptel hardware in my machine? I have found a lot of references with RTP problems which were related to RTP timing (or lack of it). My problem is that voice coming from SIP hardware is OK, but voice going from asterisk to SIP hardware is choppy, full of noise or completely cut-off. Am I going to solve my problem

regarding my previous post about SIP outgoing calls dropping with an error 481 .. this is my output from a SIP debug. the call dropped occurs at the end. Asterisk is mine, Cisco-SIPGateway is the other end (remote) and not in my control. help :) please!! Dave Signal=0 Duration=250 (no NAT) to 216.52.153.207:5060 Sip read: SIP/2.0 200 OK Via: SIP/2.0/UDP

I have made bri-stuff.0.0.2rc19 to work (I think) but I can not achieve any in-dialing nor I can dial out; this is what I have from "pri intense debug span 1" command ---------- *CLI> pri intense debug span 1 Enabled EXTENSIVE debugging on span 1 -- Executing Playback("SIP/201-a862", "tt-weasels") in new stack -- Playing 'tt-weasels' (language

Few weeks back local telco introduced option of custom ring tones. I am not talking about your phone ring tones but about ring tones you hear in your headset while phone is ringing on the other end. If I understand correctly, ringing tone is generated localy on asterisk if you are connected to phone network with E1/T1 connection. Which means that instead of regular beep-beep tone we could send

Hello All, I have a media problem while using sip communicator user agent with asterisk behind NAT.I had enabled the debug mode in asterisk and capture the results.I have attached the results with this mail.Can any one help me to fix the problem? Thanks in advance, Partha __________________________________ Do you Yahoo!? Yahoo! Mail is new and improved - Check it out!

Hello, I've been racking my brain over this for much of the day so I thought the list would probably be more helpful. A few days ago I upgraded from Asterisk 1.2 to Asterisk 1.4.5. Everything appeared to be working properly. However, on the first business day, we realized that when transferring calls (not using call parking, using the built in transfer buttons on a Cisco 7960) would not

Hi, I have a client using Mitel 5212 phones in SIP mode with a 1.4.21.1 Asterisk server (and a couple of previous 1.4 versions). They're mostly happy with the combination except for this one issue. For incoming calls only, either originating from other local SIP phones or from a PRI, calls won't get bridged (remote party get's hung up) if the call is answer too quickly on the

Hi everyone, Sorry if I'm repeating the e-mail, but I'm having problems with the list. I'm currently trying to enable call transfer to different domains in asterisk box (Asterisk 1.2.13 running on Debian etch). I have a configuration that requires me to transfer call to separate domains like ext at 10.10.10.10:5050. My calls come from a R2 channels in a board installed in the machine.

Hello. I have a strange problem. Its not possible to pickup a call that was placed with a Siemens SL75 Wlan. When this phone calls an internal number and i try to pickup (*8) the call from my phone i get nothing. It seems i have the call for one second or so but after that the call is being cancelled. No problems with other phones (polycom, grandstream). Attached the complete sip debug log

Hello everyone. I can place outgoing calls no problem with my IP500 (using teliax as our provider). Thing is, when a call comes in, 90% of the time when I pick up the handset it drops the call immediately. I turned on SIP debug, and have listed my extension config from sip.conf. Any help is greatly appreciated.... sooo close.... TIA! -Ron [3004] type=friend username=3004 password=XXX

Hullo :) I'm using Debian's Asterisk 1.0.7 bristuffed (though I'm only using CAPI for ISDN, and not HFC-S cards) and trying to transfer an incoming SIP call from sipgate.co.uk to any other extension. My phones are AT-320s (PA168S 1.43 firmware) whose documentation says to blind transfer, simply dial the number you want to transfer to, and press 'FWD'... This is what

Hello. I'm trying to use Asterisk in combination with SER, to make the routing proccess to my PSTN-Gateways. I made a simple test defining some extension in my extension.conf, when i made a call my SER (SIP) Server forward the call to Asterisk, this proccess is ok, but when the call is answered i see an INVITE going out from Asterisk to my SER Server, this invite is then passed to my

Retrying, falling of the list some how :-( -------- Original Message -------- Subject: feeling n00b again Date: 2018-08-20 09:51 From: asterisk at a-domani.nl To: asterisk-users at lists.digium.com Hi all, Long time ago, I followed a Asterisk training, and both at work and at home, was able to deploy Asterisk, make all sorts of internal call (hard/soft voip-phones, incoming/outgoing,

hi i got iconnect to work, works pretty well now except calls sometimes (more often than not) hang up after a couple of minutes.. heres a bit of the debuging Record-Route: <sip:61892142222@213.137.73.178:5060;maddr=213.137.73.176> From: sip:61892142222@natrelay.deltathree.com;tag=3281050172-73809 To: "JUSTIN XLITE" <sip:2001@61.95.68.84>;tag=as09766a78 Call-ID:

REPOSTED with MORE Info and Modified Subject Line: -------------------------------------------------------- I am using one of the Minute Provider to dial out USA numbers. Now in one of my process, we need to Dial IVR and the enter DTMF digit and then it connects to the automated IVR. When I dial out the IVR directly using Xlite and VOIP Mins provider , it works perfectly. but when In try from

Here is the CS1000 log. Again, the CS1000 using SIP accepts incoming calls just fine. However, using outgoing call files the CS1000 is hanging up after I answer the call. I dont know why? Thanks, for any assistance. Jerry my sip.conf entry is: [Nortel] type=friend dtmfmode=rfc2833 username=XXXXXXXXX disallow=all allow=ulaw allow=alaw

Hello, I notice that Asterisk always sends Subscription-State: active, even when the SIP-peer is offline (IP-phone cut from power) : /[Jul 31 11:56:58] NOTICE[32273]: chan_sip.c:26194 sip_poke_noanswer: Peer 'testacc77000' is now UNREACHABLE! Last qualify: 49// //[Jul 31 11:56:58] Really destroying SIP dialog '78b0d1701d3694b1494a0c4b55344d57 at ip-sip-server:5060' Method:

Hi. We have an odd problem with incoming SIP calls. I have attached a SIP debug log, with some asterisk verbosity as well, demonstrating the problem, below. Is this a known bug? Vital stats: - Asterisk 1.2.3 - Sipura SPA-841, SPA-941 phones - Fedora core 3 The problem manifests itself with these symptoms: - an internal SIP extension receives a call from our PRI - the SIP phone answers the