similar to: *** MGCP on the menu? Check today's special!

Displaying 20 results from an estimated 7000 matches similar to: "*** MGCP on the menu? Check today's special!"

2004 Oct 15
1
Asterisk crashes on special Transfer with MGCP/ATA 186
Hi all, i am using CVS-HEAD-08/13/04-12:00:00-BRI-stuffed-0.1.0-RC4a with Cisco ATA-186 3.1.1 atamgcp We are used to make an special ;) blind transfer like (Flash)Number(Hangup before anyone answers or ring). Then * crashes (see below) if the man in the middle is an cisco-ata-186-mgcp If one waits until the last one rings, then hangup, everything is fine. If one waits until the last one
2005 Aug 04
1
Asterisk and the IAD2431 via MGCP
I have the following upcoming install and I'm trying to do it without having to resort to Digium t1 cards. I have a Cisco IAD2431 being installed by our Carrier. That Carrier will be providing 2 IP Trunks via ethernet handoff into the Cisco IAD2431. The CIsco IAD2431 has Two T1 ports installed and we would have to install a digium card to support those two t1's. What I'd like to do
2003 May 07
2
MGCP broken
hi all I'm being spammed by these messages in the console (see below) and sound doesn't work with today's cvs. I rolled back a week, and it works fine. In addition to the sound problems, I had to enable inband dtmf squelch on the dilnk mgcp phones. if not, each pressed key was counted twice NOTICE[245776]: File chan_mgcp.c, Line 710 (mgcp_rtp_read): MGCP ast_dsp_process
2005 May 10
3
MGCP : chan_mgcp.c:1509 find_subchannel
When I try to connect to * using a Cisco ATA 188 configured with a MGPC firmware (v3.1.1), I just keep getting this message every 30 seconds or so : May 10 10:08:21 NOTICE[7913]: chan_mgcp.c:1509 find_subchannel: Gateway '192.168.1.27' (and thus its endpoint '*') does not exist Using tcpdump, I have checked that the ATA188 (with IP 192.168.1.27 and port 2427) sends UDP packets to
2003 May 22
0
MGCP NOTICE message and WARNING messsage
> Hello all, > Can someone help me on the problem which I have on MGCP phone test . I test mgcp - asterisk- zap. But I got several NOTICE message from rtp.c. > NOTICE[20501]: File rtp.c, Line 221 (process_rfc3389): RFC3389 support > incomplete. Turn off on client if possible > > -- Endpoint 'aaln/1@VG101-1-1' observed '9' > NOTICE[20501]: File rtp.c,
2009 Dec 17
2
Integrate a CPE with Asterisk in MGCP
Hello all, I'm looking for some help to try to understand why my CPE doesn't work good with Asterisk in MGCP. Here is what I want to do : - Register a TECOM AH4021 on Asterisk in MGCP with the following profile in mgcp.Conf : [general] port = 2727 bindaddr = 10.95.20.1 disallow=all allow=g729 allow=alaw 020202020202] context=mgcp host=dynamic canreinvite=no dtmfmode=rfc2833 nat=yes
2003 Oct 20
1
mgcp transfer takeback with ata186 (logs with comments - long post)
Hi, in following of a recent discussion I got to work on MGCP with the Cisco ATA186 again, and got it to work very nicely. However, there is a little thing with transfers I would like to get comments on: Call comes in from PSTN and goes to an ATA186 (MGCP) Call is answered and then, using flash, transferred to another extension If the extension is available, there can be an announcement and
2004 Jul 31
3
MGCP & Cisco ATA 186 Help
Does anybody has the expirience configuring Asterisk with Cisco ATA 186 MGCP firmware ? I have Cisco software v3.1.1 atamgcp (Build 040629A) Asterisk 1.0-RC1 On ATA i only put domain test. mgcp.conf looks like this [test] host = 192.168.195.55 context = default line => aaln/2 line => aaln/1 Asterisk CLI shows this: Jul 31 16:05:40 WARNING[135449600]: chan_mgcp.c:485
2004 Jan 22
3
MGCP w/8x8 DTA-310 and as5300 pstn gateway
Hello folks, I'm trying to get an 8x8 DTA-310 running mgcp to work. I get no dialtone & can't get it to ring. My mgcp.conf says: ; ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 0.0.0.0 [172.16.2.25] host = 172.16.2.25 context = default line => aaln/1 And here's the interesting bits of extensions.conf: [globals] ... TRUNK=H323/BYEXTENSION@pstn_gw ...
2004 May 19
2
MGCP error dialing
I am trying to dial a mgcp extention from my sip phone and i am getting this error message. anyone got any idea? error I> -- Executing Dial("SIP/2204-5dc2", "MGCP/aaln/1@10.0.1.150") in new stack May 19 22:30:01 NOTICE[1251156800]: chan_mgcp.c:1104 find_subchannel: Gateway '10.0.1.150' (and thus its endpoint 'aaln/1') does not exist May 19 22:30:01
2004 Aug 23
0
Swissvoice MGCP Error 502
I have 1 IP phone (Swissvoice IP10S) and 1 POTS phone. When I dial the number for the IP phone off the POTS phone, the IP phone rings. But when I pick up the handset on the IP phone, I get a busy signal and this message on *: Aug 23 09:38:57 NOTICE[1142106560]: chan_mgcp.c:2243 handle_response: Terminating on result 502 from svip10@00059002042b-1 Here is the entire session. svip10 is the 1 and
2005 Mar 16
1
MGCP Channel Lockup and other probelms
Hi All, I'm trying to hook up asterisk (CVS-HEAD-02/09/05-13:44:11 ) to a ADIT 600 via MGCP. Got it working really nice but now have a pretty bad problem: 1. When I perform a flash on the telephone, I usually get a second dialtone, but when I dial, dialtone doesn't break. If I flash back and forth a few times, it will eventually give me no dialtone.. here if I dial, it successfully
2010 Mar 05
0
MGCP FXO endpoint
I have a fxo endpoint installed in a Cisco router. I would like in my dialplan to get an extension call a telephone number through that fxo endpoint. Since with zaptel channels it is done like: exten => 0999,1,Dial(DAHDI/2-1/111) --> being 111 the phone number I want to call. I thought that for mgcp it would be the same, and I did: exten => 5200,1,Dial(MGCP/aaln/S0/SU3/0 at
2004 Jan 22
2
MGCP Problem.
Hi. I'm new in Asterisk with MGCP. I set up a MGCP user agent and start asterisk with the next configuration files. '--------------- extensions.conf ---------------------------------------------------- [general] static=yes writeprotect=yes [globals] ap1 => mgcp/aaln/ap200@64.76.148.186 [macro-apl1] exten => s,1,Dial(${ARG1},30,Ttmr) ;exten => s,2,Voicemail(u${MACRO_EXTEN})
2005 Jun 20
0
MGCP and SIP clients
Hi folks I seted up the asterisk with an active ISDN B1 AVM Card (german vendor) and it works fine, various SIP clients (IP fon snom, xlite under MacOSX) and also incoming and outgoing connectins. Ok. No problem. After that I configured a CP7940G with a MGCP IOS. It's connected to the asterisk too via switch. No NAT deivce between. And of course, I can call out to PSTN and also to one of the
2003 Dec 03
2
Cisco IAD with MGCP
I repost a message I put a week ago: I have a Cisco IAD 2431 which has MGCP protocol; I cannot make it to work againts Asterisk; at least there is some MGCP conversation between them but when I offhook a phone attached to IAD I get no tone at all. As anybody managed to get working Asterisk against an MGCP Cisco gateway ? Which MGCP version should I use ? Also I recently
2003 Oct 22
0
MGCP error for Cisco 7750 FXO card
Can anyone tell me what MGCP error that I'm getting means? The hardware is a MRP200 in a Cisco 7750 PBX. (Its a FXO blade with 2 slots, first one has a 4 port FXO card and the second has 2 port FXO card. It recognises those correctly, at least to the point of this error.) MGCP Debugging Enabled MGCP read: NTFY 13 aaln/S0/SU0/0@MRP200-S1 MGCP 0.1 X: 1adace42 O: L/hd from
2010 Sep 02
0
NCS - Cablemodem
Hi all, I am configuring asterisk in a cable modem network, using a motorola TM401A. I can make calls from the MTA but I can receive, display the following error: -- Executing [1500 at alberti:1] Dial("OSS/dsp", "MGCP/aaln/1 at 0-13-11-82-bd-a.ssw.intercal.net|30") in new stack [Sep 2 00:10:53] NOTICE[28062]: chan_mgcp.c:3572 mgcp_request: Asked to get a channel of
2004 May 03
1
Asterisk & MGCP / NCS
Hi everybody, I have a MTA from Terayon that I try to make run with Asterisk using MGCP channel. The device is running with MGCP 1.0 NCS 1.0 Each time Asterisk try to send a Request (Request Notify, Audit Endpoint....) the device returns error 510 "Protocol Error" Does anybody have already meet this problem and provide me support to make run it ?! (I have already try to change
2004 May 04
1
MGCP: Current CVS works for you?
Hi there, I have serious problems with MGCP and Swissvoice ip10s, and it appears that recent CVS also introduced trouble for other MGCP users. Please check and add comments in the bugtracker so that we can get a clearer picture - thanks! Also comment if things are working fine for you. http://bugs.digium.com/bug_view_page.php?bug_id=0001542