similar to: Archive Post ISDN Q.931 disconnect cause codes

Hi all, using latest asterisk-svn I want to reflect an video call incoming via an PRI EuroISDN channel to another outgoing PRI channel, and I want the the outgoing channel to have the exact same bearer capability < Bearer Capability (len= 5) [ Ext: 1 Q.931 Std: 0 Info transfer capability: Unrestricted digital information (8) < Ext: 1 Trans mode/rate:

Hi all, I have to asterisk-1.0.9BRIstuffed-0.2.0n boxes each equipped with a TE410P. Box A is connected with pri1 to the PSTN. Box B is connected with pri1 (cpe) to the Box A at pri2 (net). Now I want Box B to dial out to the PSTN tunneled thru Box A and have it get all ISDN indications in case of call failure, eg. unallocated destination number etc. But currently Box B always gets only

I just downloaded the cvs version CVS-07/28/03-14:45:19 and now I cannot recieve the the calls from the zaptel interface which is a E100P with pri signaling. That is something with asterisk becouse rolling back to version from 06/23/03 using the new libpri and zaptel fixes the problem. Here is an exept from the config: [macro-stdexten]; ; ; Standard extension macro: ; ${ARG1} - Extension

Hey all. We have a DS3 circuit with GBLX split off into 7 systems with a 4 port sangoma card (A104D) in the first 2 systems, and digium T410P cards in the other 5. GBLX numbers their spans from 0 to 3 instead of 1-4 and we have a NFAS configuration with the d-channel on chan 96. All of our systems are running 1.0.7 for stability reasons (and no good time for maintaince, the entire platform

Hi! For demonstration purposes I try to bridge an incoming video call from a 3G mobile handset to another 3G mobile handset using asterisk as "switch". On the incoming call leg I see all expected bearer capabilities (Digital, 64k Transparent, G.7xx 384k video) but on the outgoing call leg the bearer capability G.7xx 384k video get lost and therefore the call is dropped from the mobile

Salve, I'm somewhat stuck on how to get DTMF working with my setup and googling didn't yield anything similar. My setup consists of one CAPI-capable board (AVM Fritz!DSL) connected to a BRI (T-ISDN), one HFC-S board running in NT-mode connected to an internal S0 bus with some ISDN devices (DECT stations, TA) and, of course, some ethernet interfaces. ISDN standard used is Euro-ISDN.

I am trying to put a call on a E1 ISDN : The configuration are simple: zapata.conf : [channels] context=inbound switchtype=euroisdn signalling=pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes ;echocancel=no echocancelwhenbridged=yes rxgain=0.0 txgain=0.0 ;immediate=yes immediate=no callerid => asreceived amaflags

Hi, I have this setup: E1 PRI PSTN -- Asterisk -- Alcatel PBX - analog phones Can someone tell me what's wrong with this call initiating from an analog phone connected to Alcatel PBX? It dies with NOANSWER but all works if I call other destination numbers. Dialplan is a simple Dial(zap/g1/0984465691) statement. At the end you'll find also zapata.conf.

Hi folks. My client is wanting to use call forwarding configured on their phones (Linksys SPA942), with a PRI from their provider. When we configure call forwarding, we invariably get a "The number you have dialed is not in service" message from the providers. Examining the detailed dial plan debugging as well as the PRI debugging, the number is dialed correctly. The only difference

Hey all, I am running a Asterisk 1.2.9.1 with Sangoma A101 card, newest firmware, configured with a help from Sangoma Tech Support, running fine. It is connected to a PRI circuit split from Cisco MC 3810, which in turn is connected to a Converged T from CTC Communications. While Asterisk works fine and I can call in/out on my BV account, I am only able to dial in through CTC. I have spent

I have this setup: (PSTN E1 PRI) -- Asterisk -- (crosscable) -- Alcatel PBX --- analog phones and a few of VoIP phones directly connected to Asterisk. Calling a number (just one!) - an automatic responder (IVR) - from VoIP phones works, from analog phones doesn't work: NOANSWER after a few seconds. I'm using no 'r' in dial options (this caused a problem with an IVR some time

Hi all, I'm debugging a PRI problem, i can see the calling number but i get a busy all the time. From the output below, I guess asterisk hangs up immediately. Can anyone point out what the problem is? Thanks in advance. *CLI> < Protocol Discriminator: Q.931 (8) len=32 < Call Ref: len= 2 (reference 4865/0x1301) (Originator) < Message type: SETUP (5) < [04 03 80 90 a3] <

Hi all, I tried to connect the bristuffed(0.3.0-PRE-1i) * to an Alcatel PBX via BRI (zaphfc) and Q.SIG. The Alcatel PBX is connected to the outside world and should forward our calls to the telco. This setup works correctly as far as I use euroisdn as the switchtype. The first problem was that it is only possible to run the * side in CPE-mode -- I wanted NET. Anyway, I configured * this way:

Hi all, I have an asterisk-server (cvs-head from august) connected to a carrier's switch (DMS/Euroisdn) via a te410p, and I am having problems with DDI (standard 'official pstn' number plus extra digits for 'internal' use) Basically, when the entire number (including the extra digits) is dialled via a redial or a programmed key, I see the entire called party number (including

We've got a EuroISDN (32 channels) with a TE405p, running cvs head as of 5 days ago. In the past couple of days, we've hit a scenario where incoming calls to the * pbx from the PSTN are being marked as busy, but outgoing calls work just fine. When we reboot *, the problem goes away. Has anyone else had this ? I've attached a PRI debug below. I've changed the phone numbers (x

Is there a setting somewhere in * to define whether I am receiving callerID or true ANI? Global Crossing claims they are sending ANI but I dont think so. My understanding of ANI is that it is always sent, regardless if callerID is blocked. If I dial *67 and my DID, I get "Presentation: Presentation prohibited of network provided number" and no number. Before I call GC on Monday

I there, I have some trouble to do working caller id name for outgoing calls on the PRI we just installed. Caller id name work on incoming calls only. Caller id number work on incoming and outgoing calls. The provider, Goup Telecom, said that's in what i'm sending. They said that I send the cid name in ascii code and to do it working, I need to send it in hex. So I take some traces

We are still having problems getting a Wildcard to work with a German E1 (PMX) interface. When starting asterisk it shows all B-channels starting up successfully (although our carrier told us only the first B-channel starts, if any at all). Incoming calls are not being signaled at all. (They seem to be intercepted by the carrier's switch, as no B-channel is up) Outgoing calls sometimes work,

Asterisk 1.8.4-rc2 (and 1.8.3) DAHDI Version: 2.4.1.2 libpri version: 1.4.12-beta3 We are having a problem with getting the nationalprefix option of chan_dahdi.conf to work. National calls do not have a "1" added to them when nationalprefix=1. The PRI debug shows the call coming in as a National Call, but the dialplan sees the call without a 1. chan_dahdi.conf: <snip>

Hi all, I have some problem to send a FAX to a given number. I use asterisk 1.2.18, on a openSUSE 10.2, i586 host. The FAX is sent out via an ISDN PRI interface, I'm in Germany, and the destination FAX devices are in Germany too, but in different areas, so I have to use a city prefix. I did set the pri device in debug mode, below are two calls, to two different FAX numbers, the first is