similar to: Reliable Provider

Anyone using asterisk with VoicePlus ? Looking for a new provider and wanted to get a little feedback

I've been trying to use net2phone's sip service at sip.net2phone.com with * but keep getting SIP/2.0 401 Unauthorized. Do you know if this should be possible? So far: I can use an ata186 to connected directly to n2p through sip.net2phone.com without any special settings. I can connect from * to iconnecthere, but, whatever I try from * to n2p produces "SIP/2.0 401 Unauthorized"

Hello, My server is Mandrake 10.1 eth0 is WAN with static IP connected to 512k DSL eth1 is LAN. I am using squid proxy for internet with NSCA auth. I am able to send and recieve mails. One of the client system wants to be able to make net2phone calls. As of now he is not able to. Howto allow net2phone calls ? Thanks Varun

Hi, I?m looking for settings to configure net2phone carrier in my asterisk. I found this configurations, but it?s not work. I don?t known if this configuration is for voice line or voice access account. Anybody can help me, with other configuration? Thanks. ---- *sip.conf* [general] useragent = X-Lite release 1103m register => PHONENUMBER:PASSWORD@sip.net2phone.com [net2phone] type = peer

FYI there is a way to do 911 its called E-911 enhanced 911 the user has to set it up with the local emergency services to it and you setup your pbx to xmit the data. Here is the fcc rule about it http://www.fcc.gov/911/enhanced/

I've had some serious issues with Teliax as of late with their "new" Denver server. DTMF issues, IAX2 connection issues, and major latency issues. They are blaming it on "1.2 vs 1.4 asterisk compatibility issues". I have had zero problems with their old servers. Voicepulse has been WAY better, but no flat charges, no 729. Frankly, even my broadvoice (yikes!)

Hi All, As Net2Phone don't permit more than one session per account, I configured about 10 sip trunks and configure multiple trunk routing but once the first trunk is used I cannot make additional calls, I also cofigure my dial plan in other way using the chanisavail command but still not working. The chanisavail command configuration is correct as I can make calls using other trunk than

Stealth Communications Announces Registry to Avoid Access Fees Posted on: 04/23/2004 Stealth Communications Inc. today announced the official launch of a registry that allows service providers routing calls over the Internet to avoid paying local phone companies access charges. The VPF ENUM Registry allows carriers to map telephone numbers to IP addresses for such things as SIP phones and

I can cut and paste the log file from a reload right now, and provide you with the other information when I get home after work: tmp*CLI> sip debug SIP Debugging Enabled tmp*CLI> reload Mar 21 14:52:42 NOTICE[23231]: indications.c:397 ast_unregister_indication_country: Removed default indication country 'us' 11 headers, 0 lines Reliably Transmitting: REGISTER

Hi! Net2Phone is getting a common SIP status code, "404 Not Found," when trying to place a call to our Asterisk server. We're hoping someone on the list can shed some light on why this is happening. We can process a call from Asterisk to Net2Phone without any problems. Net2Phone sends the INVITE but immediately gets the "404 Not Found." The "To:" field

Hi All, I am trying to use iconnecthere to make outbound calls. I am behind a linksys router. I keep getting this error 481 "Call Leg/Transaction Does Not Exist". Does anyone have any prior experience with this problem. Any leads will be much appreciated. Attached are the conf files and logs #SIP.CONF ; SIP Configuration for Asterisk [general] port = 5060 ; Port

Hi friends, I've noticed that first register message sent by * always get rejected by the destination sip server. Then * sends a second registration message ( with Autherization section, and that get accepted by the destination host). Why is this ? Isnt there a way to tell * to send with Autothorization message the first attempt ? Asterisk sends this first 9 headers, 0 lines 11 headers,

I know that the wiki has an extensive list of European VoIP providers out there....but there's so many that it's kind of hard to sort through. So I was wondering if anyone could recommend some reliable SIP/IAX termination providers in Europe? Something like VoicePulse Connect, NuFone, Vitelity, or Junction Networks based out of Europe. I really don't trust a US VoIP company for

Dear, I have this scenario: - PBX Asterisk 1.6.2.10 with private IP 192.168.0.10 - Behind a Cisco ASA firewall that connects to Internet - SIP trunk to Net2Phone with these parameters (nat=no): host=200.58.113.60 username=DOLLY secret=123456 port=5060 type=peer dtmfmode=rfc2833 disallow=all allow=alaw&ulaw nat=no canreinvite=no qualify=yes -Softphones Xlite The PBX can't register to

Hello All, I have gone thru all the resources I could find on google on asterisk + iconnect and managed to get outgoing calls working. However, I cannot get incoming calls to work at all. With the sip debug on, I can see that something is happening everytime a call is received from iconnecthere, but I get an invalid tone on the caller side. The call never rings anywhere on the asterisk. Would

Hi, I have a deltathree account and I can place calls but I can't receive calls. I use Grandstram sip phones. When I call my deltathree phone # the voicemail is answer :(( I need some help and solutions from the guys who allready are using deltathree. I search on Internet and I try all types of configurations... :( This is my configurations files: - sip.conf - [general] port = 5060

Hi, I wish to connect several ATA186 Phones to each other, to iconnecthere and to the PSTN using asterisk. Please tell the appropriate settings for firewall (ports to open etc.) sip.conf and extensions.conf(part relevant to iconnect). Also I would be glad to get a working example of your ATA186 configuration. I tried searching the mailing lists and several sites but did not find an answer.

This morning, I received a very strange error message on the Asterisk console. The error occurs when I try to access iconnect WARNING[196621]: File chan_sip.c, Line 386 (__sip_xmit): sip_xmit of 0x80d0854 (len 649) to 213.137.73.178 returned -1: Bad file descriptor I also get this error when I try to reload: WARNING[16384]: File chan_sip.c, Line 5355 (reload_config): Unable to get IP address for

Is anyone signed up with Vonage and using an asterisks box?? Also what VOIP providers would anyone recommend? -- James Moran Potential Technologies http://www.potentialtech.com

Quick question for the experts: I'm seeing stuck SIP channel(s) scheduled for destruction stay open. This appears to happen after (apparently successfully) registering with a SIP peer. Any ideas where to start digging into this? I'm running today's CVS, however the problem existed before and does persist. Thanks, Kai-Uwe Example: (registration with iconnecthere.com) ast1000*CLI>