similar to: G.729 and h323.conf

Hello, I managed to terminate calls from cisco: as5300 and 7206 to asterisk over h323. I tested both oh323 from inaccessnetwork and JerJers chan_h323. I used 1.12.2 version of oh323 and 1.5.2 version of pwlib. After latest changes from JerJer chan_h323.c works ok when receiving traffic from ciscos. I havnt found any audio problems although I didnt send much traffic. Latest oh323 has some

I've previously been using G711alaw on both the AS5300 and the phones but feel the need for a less bandwidth hungry codec for those users that are connected behind ADSL and so was investigating G.729 but .. Firstly I found that on my AS5300 I have either G.729r8 or G.729br8 and on the 7940 phones I have G.729a, I'm not sure which interoperate the best with each other and so was wondering

Hello, I have 5 digium's g.729 codecs and succesfully register with asterisk, I have incomming call from my cisco AS5300 to Asterisk through IP. But Asterisk always use g711 ulaw instead of g.729. When I disable all other codecs other than g.729 in both cisco and asterisk, calls get dropped once connected. The codec list show on my cisco AS5300 for g.729 are: g729r8 g729br8 I suspect that

Hi Users, Administrators and Pavel Jezek, You prefer chan_h323 from asterisk tree and it's of course that use channels by tree is very good. But in 1.2.x, the chan_h323 is very simple and the chan_oh323 is so bad. And I work with chan_ooh323, that it's too from Digium and work good! And I am Studing one possible change to Asterisk 1.4.x , but in 1.4.x the oh323 channel don't have more,

Hi, what's the difference between h323 and oh323 modules? which one should I use? Regards. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030722/3d3edb73/attachment.htm

Is H323 built into the current CVS? If so, could someone give me an idea of a simple config? thanks, darran -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030429/fffec1d1/attachment.htm

Hello, I have a strange h323 issue. After executing command "Dial("SIP/333-0d1dfe00", "H323/361737052390920 at ccg|5|tT")" at Oct 18 22:32:23. Meanwile I have sniffing traffic on port 1720. The call was established just at Oct 18 22:33:03 (New H.323 Connection created.) and also packet sniffer grabs the h323 invites at this time also. So my question is what

Dear friends, I have compiled and installed h.323 in my asterisk. And I have a service from a H.323 VoIP provider who give me user, password and gatekeeper IP address. All configured. But when I start my asterisk i receive the following error and h.323 calls can not be making and/or receiving. [chan_h323.so]=> (The NuFone Network's Open H.323 Channel Driver) == Parsing

Hi All. I'm using RedHat 9 I configured the chan_h323 and asterisk from CVS. This is the scenario SJ_lab_phone(sip) ---------------> Asterisk -------------> H323 GK --------------> PSTN I have tried all codec's and always the same result, the called phone will ring without dropping for how ever I allow it to but as soon as it is answered it immediately gets disconnected.

I receive the following error when I try to call another H323 extension from another H323 when going through *. NOTICE[27669]: File channel.c, Line 1325 (ast_set_read_format): Unable to find a path from 1 to 8 NOTICE[27669]: File channel.c, Line 1296 (ast_set_write_format): Unable to find a path from 8 to 1 WARNING[27669]: File chan_h323.c, Line 528 (oh323_write): Asked to transmit frame type 1,

Rafael J. Risco G.V. wrote: > > On Sat, 11 Dec 2004 16:49:12 +0000, Corvin <corvin.dun@wp.pl> wrote: >> Dnia sobota, 11 grudnia 2004 15:32, Rodolfo Grave napisa?: >> > Hi. >> > >> > I need to set up H323 on an Asterisk box. I've succesfuly compiled the >> > asterisk oh323 (including of course all the dependencies: PWlib and >> >

Hi everyone, Installed asterisk from yum repository but I think H.323 is not supported as I tried commands like this and they don't work: - *h.323 debug*: Enable chan_h323 debug - *h.323 gk cycle*: Manually re-register with the Gatekeper - *h.323 hangup*: Manually try to hang up a call - *h.323 no debug*: Disable chan_h323 debug - *h.323 no trace*: Disable H.323 Stack Tracing

Hi, I have licensed the digium G.729A codec. But for some reason incoming and outgoing calls will ALWAYS use G.711a. When I force my phone to only accept G.729 then an incoming call from ZAP goes straight to my voicemailbox as the phone doesn't accept the codec Asterisk wants, even if I force it in sip.conf. Is there anywhere else I need to look to tell ZAP to use G.729 preferrably ? The

Hi, I am trying to replace my Cisco 5300 gateway with my new Zap TE405P card. Incoming calls and outgoing calls between my cisco and my SIP phone works fine on G.729. Recording messages in the asterisk voice-mailbox also works fine from both my SIP phone as well as PSTN -> Cisco -> Asterisk. I have licensed the digium G.729A codec. When I connect my ISDN PRI to my Zap card and I call

Hi All, I have set up a box that will be used as follows: SIP Phone ----> Asterisk ----> Cisco H323 VoIP Server 192.168.1.5 192.168.1.50 192.168.1.80 Asterisk is running the latest CVS and oh323 driver. The SIP phone is a Grandstream Budgetone 100. I have everything setup and running with G.711 ALAW and ULAW and i'm able to make calls through

Hi, I use with asterisk gnugk a gatekeeper for h323 client. I don't understand why asterisk can't have the H323-ID (callerID). In the gatekeeper's monitor I have this H323-ID but not in asterisk. Does anyone know something about it, or how can I send a caller ID to asterisk ? Rattana -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm really struggling with an Asterisk 1.6.2.7 install (on centos 5.4) The pwlib + opal packages don't satisfy Asterisk's configure script (to let H323 compile), so I removed those and added the latest ptlib + h323plus (from h323plus.org) I can compile ptlib and h323, but when I load chan_h323 in asterisk I get a segfault. I had to point LD_LIBRARY_PATH to /usr/local/lib with the

Hi all, i have purchased the g.729 codec from digium. The registration was successful. (with the "old" binary) But there're a few questions: - should not the codec listed in the codec list when i enter "show codecs" ? - the codec is named with g729b but if i enter show codecs there is a codec g729a listed also the g729b is not installed. what is the difference between

Hello All, I am trying to setup a SIP to H323 system using SER, Asterisk And GnuGK. Following is the configuration: CISCO ATA (NAT) -> SER -> ASTERISK -> GNUGK My Cisco ATA is registered with SER and When I dial a number, SER forwards the call to Asterisk, and Asterisk forwards the call to the GateKeper. This is ok, call reaches the gatekeeper, however the gatekeeper drops the call

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/jpeg Size: 2593 bytes Desc: not available Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20050516/734618ce/attachment.jpeg