similar to: SIP Transfer problem

I have a Cisco 7960 & IpDialogs that I am not able to use the transfer button on it. What happens is that it puts the call on hold and then it gives you a dial tone. You can dial but it will not transfer the call. What we are trying to do is transfer to extension 700 for parking so another person can pick up the line. We can not use the # key to do this due to we have several IVR's

I just got 2 IpDialog phones for use with my Asterisk system. I have been able to get the phones to just dial local extensions but it is not able to register with my system correctly. I would like to know if someone has set these phones up before and how they did it! Is there any examples for use with Asterisk? They seem simple enough to config with there web interface. Thanks

I have about 5 snom 200 phones working fine with everything. Voicemail, Transfers and all. Except I can't seem to use them to pickup parked calls nor place a call on park. I also have sipura-2000 with analog phones that are able to pickup parked calls and to park them. Most of them are on firmware 2.04g I have upgraded one to 2.05c for testing but this did not fix the problem. I get no error

Ok here is another problem I have run into. I have a Sipura 2000 and I have been able to configure line 1 with only one small problem. But I can't get the line 2 working with asterisk. Here are samples of my sip.conf and extensions.conf. If I disable line 1 I can then get line 2 working. Is there a sample configuration for the Sipura to get both ports working with Asterisk. Sip.conf

I am trying to get the following phones for testing. Is there a distributor in the US that is able to sell me these Sip phone and ATA adapters? I can not afford the Cisco phones there too hard to configure and too expensive! 1 - Sipura SPA-2000 2 - Grandstream Sip phone BT-102 1 - Grandstream HT-286 1 - Snom 105 Sip phone. I have called and emailed chagres but they have not reply. Nor

I would like to know if anyone has come up with a script for 911 dialing rules that put correct information on our locations. We have our office in 3 different building one being our production & shipping dock. It is almost 2 blocks away. We are connected with Ethernet Wireless between the buildings and have Sip phones setup in the other 2 locations. All the phones are working just fine.

I have 2 Snom 200 and would like to get them to work properly with Asterisk. With the Firmware 2.02t I am able to use the phone. But only one line configured. With there newer firmware 2.03o it will not allow me to make calls. But I can get calls on the unit. Again the 2nd line is not able to be registered. Is this an issue with Asterisk or Snom? I could use some example configuration

I have a question on SIP devices that are setup and working but you change the login name and contents to them why does asterisk need to be shut down and restarted for them to work? I have reloaded extensions and done a reload command. But the updated sip phones do not work until I shut down and restart asterisk. Is there any other way to update them without restarting the system? Since the

I am trying to get a building that has 3 company's on one asterisk server. I need to make the IVR via DID take them to there right menu. So far I have everything working except when they goto via standard_marco to an extension and are sent to voicemail they are dropped off in the first menu and not the one they came from. In other word sent to another company's menu. If it happens to be

I have gotten the Cisco 7960 working with my Asterisk system under SIP. The version is 5.03 that I am using. Cisco Support said I should not upgrade to version 6 yet. My next question is the sound is patchy when people here me. But I can hear them just fine not patchy. I have the 188 page Admin manual and it seem not to say anything about improving the sound. All other phones like IPDialog work

I would like to prevent * from dialing 900 and 976 numbers. I setup the following settings in extensions.conf. But this does not seem to work! I don't know what I am doing wrong please help! exten => 1900XXXXXXX,1,Congestion exten => XXX976XXXX,1,Congestion exten => XXX976XXXX,1,Congestion exten => 1XXX976XXXX,1,Congestion exten => 91900XXXXXXX,1,Congestion exten =>

Anyone in need of some of these? Garrett Smith Sales Executive garrett.smith@b2llc.com B2 Technologies 454 Sonwil Drive Buffalo, NY 14225 (716) 250-3408 Direct (716) 630-1548 Fax (716) 903-9495 Cell AOL IM: B2sales Specializing in New and Used equipment from vendors including Cisco Systems, Juniper, Adtran, Dialogic, Lucent, Nortel, Sipura, Granstream, Snom, Mediatrix,

I've got a situation where I need to use a transfer to the parking lot as hold, but am not going to use BLF indicators on the phone to pick up the parked calls so I need to hear the 3-digit extension after the transfer. I'm using Snom 300 phones and have tried setting a programmable button to Key Event F_TRANSFER 700, which successfully does the transfer but cuts off audio so you

I have a problem that sometimes lines will go into what I call never never land. The Asterisk system will put a line with <Zombi> on it when you type show channels it will make the analog phone line dead. And on the CLI it says: astsvr*CLI>Zap/1-2<ZOMBIE>(macro-twoline-exten,s,1)Up Dial Zap/1-2|20|r I have tried to release it with soft hangup Zap/1 & also soft hangup

Having spent the better part of an hour searching the archives and voip-info I hesitantly ask what appears to be an obvious question but one I cannot find an answer for. Using Grandstream phones it seems that the only way to support Call Parking is to enable # transfers (i.e. use T in the dial command) since pressing the TRANSFER button on the BT phone is blind and one does not hear the call

Hi all, DIAX 0.9.3 is available for download from the same place: http://www.laser.com/dante or http://www.geocities.com/tdanro The new DLL contain the latest updates made by Steve in the iaxclient library. Still just IAX1 is supported (for the moment). What's new in 0.9.3? - accept blank passwords; - accept for registration/calls host names, not only IP Address; - password no

I have a Mediatrix 1204 FXO gateway setup for SIP. I would like to know if anyone has gotten this item to work with Asterisk. I need to get a 2 or 4 port FX0 gateway working with asterisk. The Idea is the following. PBX at lets say any Hotel(Analog lines FXS) - FX0 Gateway(1204) -- {Internet} -- Asterisk - local IVR system. (IVR is not at present running Asterisk old dialogic system has FX0

Yes folks it's me a Newbie. Remember I am also a non-Linux person trying to learn. I have a production Server running Asterisk .5 12/02/03 CVS, and would like to upgrade it to the new .71. Has anyone come up with instructions (Documentation for us newbie) on how to do this? My server is running Mandrake 9.0 which I know nothing about! Sorry if this sounds stupid but all the instructions I

Hi, I am using a number of snom190 phones, and an asterisk "gateway" server, and recently started experimenting with call transfers. The snom phones provide support for attended and un-attended call transfer, so I would rather use that than call-parking. I have found that un-attended transfer works fine, and that attended transfer works fine if the originating phone call is NON-SIP

I am new to this forum. As well as a new user of Asterisk. My vendor installed the system and we are still trying to get all the bugs out of it! I have a few questions about configuration and a program to view who is on what extensions. I am looking for a program that will work on my Receptionist work station. She is running Windows 2000 pro. We have not plans on upgrading to XP pro so